-- ******************************************************************* -- Airespace Switching MIB -- Copyright 2001 Airespace, Inc. All rights reserved. -- This SNMP Management Information Specification -- embodies Airespace's confidential and proprietary -- intellectual property. LVL7 Systems retains all title -- and ownership in the Specification including any revisions. -- This Specification is supplied "AS IS", Airespace -- makes no warranty, either expressed or implied, -- as to the use, operation, condition, or performance of the -- Specification. -- Status: Release -- Version: 3.2 -- Internal Source Code Version:1.75 -- Date: 19 Dec 2005 -- ******************************************************************* AIRESPACE-SWITCHING-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, IpAddress, Counter32, Integer32, Unsigned32, TimeTicks FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF DisplayString, PhysAddress, RowStatus, MacAddress, TruthValue FROM SNMPv2-TC airespace FROM AIRESPACE-REF-MIB dot1qVlanIndex, dot1qFdbId FROM Q-BRIDGE-MIB IANAifType FROM IANAifType-MIB; --******************************************************************** --* MODULE IDENTITY --******************************************************************** bsnSwitching MODULE-IDENTITY LAST-UPDATED "200604100000Z" ORGANIZATION "Airespace, Inc." CONTACT-INFO " Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-wnbu-snmp@cisco.com" DESCRIPTION "This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration, statistics and status information about the controller. This includes controller statistics and provides information such as Inventory, Trap logs, memory and CPU. This MIB also provides configuration of CLI, SNMP, LAG, DHCP, Spanning Tree, etc. The relationship between controller and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol. " REVISION "200604100000Z" DESCRIPTION "Updated MIB with description and format" ::= { airespace 1 } --******************************************************************** -- Major sections --******************************************************************** agentInfoGroup OBJECT IDENTIFIER ::= { bsnSwitching 1 } agentConfigGroup OBJECT IDENTIFIER ::= { bsnSwitching 2 } agentSystemGroup OBJECT IDENTIFIER ::= { bsnSwitching 3 } stats OBJECT IDENTIFIER ::= { bsnSwitching 4 } switchingTraps OBJECT IDENTIFIER ::= { bsnSwitching 50 } bsnSwitchingGroups OBJECT IDENTIFIER ::= { bsnSwitching 51 } bsnSwitchingCompliances OBJECT IDENTIFIER ::= { bsnSwitching 52 } --******************************************************************** -- agentInventoryGroup --******************************************************************** agentInventoryGroup OBJECT IDENTIFIER ::= { agentInfoGroup 1 } agentInventorySysDescription OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Inventory system description." ::= { agentInventoryGroup 1 } agentInventoryMachineType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the Machine used in the Switch." ::= { agentInventoryGroup 2 } agentInventoryMachineModel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Machine Model. " ::= { agentInventoryGroup 3 } agentInventorySerialNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Serial number of the switch." ::= { agentInventoryGroup 4 } agentInventoryMaintenanceLevel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Inventory Maintenance Level" ::= { agentInventoryGroup 6 } agentInventoryBurnedInMacAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Burned-In MAC Address" ::= { agentInventoryGroup 9 } agentInventoryOperatingSystem OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Operating System running on this unit" ::= { agentInventoryGroup 10 } agentInventoryManufacturerName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the switch manufacturer." ::= { agentInventoryGroup 12 } agentInventoryProductName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the product." ::= { agentInventoryGroup 13 } agentInventoryProductVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Version of the product." ::= { agentInventoryGroup 14 } agentInventoryIsGigECardPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the Switch contains a Gigabit ethernet card ." ::= { agentInventoryGroup 15 } agentInventoryIsCryptoCardPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the switch is carrying a Crypto card." ::= { agentInventoryGroup 16 } agentInventoryIsForeignAPSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "States whether the switch supports third party Access Points." ::= { agentInventoryGroup 17 } agentInventoryMaxNumberOfAPsSupported OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of APs supported with this Controller." ::= { agentInventoryGroup 18 } agentInventoryIsCryptoCard2Present OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the switch is carrying second Crypto card for 4400 controller." ::= { agentInventoryGroup 19 } agentInventoryFipsModeEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if FIPS (Federal Information Processing Standards) mode has been enabled on the controller.False if FIPS mode has not been enabled. FIPS mode can only be enabled through console." DEFVAL {false} ::= { agentInventoryGroup 20 } --******************************************************************** -- agentTrapLogGroup --******************************************************************** agentTrapLogGroup OBJECT IDENTIFIER ::= { agentInfoGroup 2} agentTrapLogTotal OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of traps sent since last reset." ::= { agentTrapLogGroup 1 } agentTrapLogTotalSinceLastViewed OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of traps sent since last viewed." ::= { agentTrapLogGroup 3 } agentRadioUpDownTrapCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of AP Up/Down traps sent since last reset." ::= { agentTrapLogGroup 5 } agentApAssociateDisassociateTrapCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of AP Associate/Disassociate traps sent since last reset." ::= { agentTrapLogGroup 6 } agentApLoadProfileFailTrapCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of AP Load Profile Failure traps sent since last reset." ::= { agentTrapLogGroup 7 } agentApNoiseProfileFailTrapCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of AP Noise Profile Failure traps sent since last reset." ::= { agentTrapLogGroup 8 } agentApInterferenceProfileFailTrapCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of AP Interference Profile Failure traps sent since last reset." ::= { agentTrapLogGroup 9 } agentApCoverageProfileFailTrapCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of AP Coverge Profile Failure traps sent since last reset." ::= { agentTrapLogGroup 10 } --******************************************************************** -- agentTrapLogTable --******************************************************************** agentTrapLogTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentTrapLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Agent Trap Log" ::= { agentTrapLogGroup 4 } agentTrapLogEntry OBJECT-TYPE SYNTAX AgentTrapLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Agent trap log entry" INDEX { agentTrapLogIndex } ::= { agentTrapLogTable 1 } AgentTrapLogEntry ::= SEQUENCE { agentTrapLogIndex Integer32, agentTrapLogSystemTime DisplayString, agentTrapLogTrap OCTET STRING } agentTrapLogIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Unique index of trap entry" ::= { agentTrapLogEntry 1 } agentTrapLogSystemTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred." ::= { agentTrapLogEntry 2 } agentTrapLogTrap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "Description of the trap sent." ::= { agentTrapLogEntry 22 } --******************************************************************** -- agentSwitchInfoGroup --******************************************************************** agentSwitchInfoGroup OBJECT IDENTIFIER ::= { agentInfoGroup 3 } agentSwitchInfoLwappTransportMode OBJECT-TYPE SYNTAX INTEGER { layer2(1), layer3(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The LWAPP transport mode specifies if the switch is operating in Layer2 or Layer3 mode. This attribute gives the current mode the switch is operating on." ::= { agentSwitchInfoGroup 1 } agentSwitchInfoPowerSupply1Present OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is to indicate if the switch has Power Supply 1 present on it. This is applicable to the 4200 series and will always return true for the earlier device versions." ::= { agentSwitchInfoGroup 2 } agentSwitchInfoPowerSupply1Operational OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is to indicate if the switch's Power Supply 1 is operational. This is applicable to the 4200 series and will always return true for the earlier device versions." ::= { agentSwitchInfoGroup 3 } agentSwitchInfoPowerSupply2Present OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is to indicate if the switch has Power Supply 2 present on it. This is applicable to the 4200 series and will always return false for the earlier device versions." ::= { agentSwitchInfoGroup 4 } agentSwitchInfoPowerSupply2Operational OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is to indicate if the switch's Power Supply 2 is operational.This is applicable to the 4200 series and will always return false for the earlier device versions." ::= { agentSwitchInfoGroup 5 } --******************************************************************** -- agentResourceInfoGroup --******************************************************************** agentResourceInfoGroup OBJECT IDENTIFIER ::= { agentInfoGroup 5 } agentCurrentCPUUtilization OBJECT-TYPE SYNTAX INTEGER(0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Current CPU Load of the switch in percentage." ::= { agentResourceInfoGroup 1 } agentTotalMemory OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total RAM of the switch in Kbytes." ::= { agentResourceInfoGroup 2 } agentFreeMemory OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Free RAM of the switch in Kbytes." ::= { agentResourceInfoGroup 3 } --******************************************************************** -- agentWcpInfoGroup --******************************************************************** agentWcpInfoGroup OBJECT IDENTIFIER ::= { agentInfoGroup 6 } agentWcpDeviceName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the name of the device this controller is residing on." ::= { agentWcpInfoGroup 1 } agentWcpSlotNumber OBJECT-TYPE SYNTAX Unsigned32(1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The slot number on the Wcp Device that this controller is residing on." ::= { agentWcpInfoGroup 2 } agentWcpPortNumber OBJECT-TYPE SYNTAX Unsigned32(1..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number on the Wcp Device that this controller is residing on." ::= { agentWcpInfoGroup 3 } agentWcpPeerPortNumber OBJECT-TYPE SYNTAX Unsigned32(1..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of this controller's peer on the same slot on Wcp Device that this controller is residing on." ::= { agentWcpInfoGroup 4 } agentWcpPeerIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of this controller's peer on the same slot on Wcp Device that this controller is residing on." ::= { agentWcpInfoGroup 5 } agentWcpControllerTableChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the checksum that tracks the changes in the agentWcpControllerInfoTable. If there is any change in the information on this table, the checksum changes." ::= { agentWcpInfoGroup 6 } agentWcpControllerInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentWcpControllerInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the wireless controllers on a WCP device." ::= { agentWcpInfoGroup 7 } agentWcpControllerInfoEntry OBJECT-TYPE SYNTAX AgentWcpControllerInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for a wireless controller on a WCP device." INDEX { agentWcpControllerInfoSlotNumber, agentWcpControllerInfoPortNumber } ::= { agentWcpControllerInfoTable 1 } AgentWcpControllerInfoEntry ::= SEQUENCE { agentWcpControllerInfoSlotNumber Unsigned32, agentWcpControllerInfoPortNumber Unsigned32, agentWcpControllerInfoIpAddress IpAddress } agentWcpControllerInfoSlotNumber OBJECT-TYPE SYNTAX Unsigned32(1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The slot number on the Wcp device that a controller is residing on." ::= { agentWcpControllerInfoEntry 1 } agentWcpControllerInfoPortNumber OBJECT-TYPE SYNTAX Unsigned32(1..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number on the Wcp Device that a controller is residing on." ::= { agentWcpControllerInfoEntry 2 } agentWcpControllerInfoIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The management IP Address of a controller." ::= { agentWcpControllerInfoEntry 10 } --******************************************************************** -- agentProductGroup --******************************************************************** agentProductGroup OBJECT IDENTIFIER ::= { agentInfoGroup 4 } --******************************************************************** -- productGroup1. This includes the 4000 switch series: 4012, 4024 and -- the 4100 appliance series: 4101 and 4102 --******************************************************************** productGroup1 OBJECT IDENTIFIER ::= { agentProductGroup 1 } --******************************************************************** -- productGroup2. This includes the Branch Office Switch series --******************************************************************** productGroup2 OBJECT IDENTIFIER ::= { agentProductGroup 2 } --******************************************************************** -- productGroup3. This includes the 4200 switch series: 4202 and 4204 -- --******************************************************************** productGroup3 OBJECT IDENTIFIER ::= { agentProductGroup 3 } --******************************************************************** -- productGroup4. This includes the Catalyst 6k series with 2 -- 4204s on a single blade --******************************************************************** productGroup4 OBJECT IDENTIFIER ::= { agentProductGroup 4 } --******************************************************************** agentCLIConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 1 } --******************************************************************** -- agentLoginSessionTable --******************************************************************** agentLoginSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentLoginSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's login session" ::= { agentCLIConfigGroup 1 } agentLoginSessionEntry OBJECT-TYPE SYNTAX AgentLoginSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Login Session Entry" INDEX { agentLoginSessionIndex } ::= { agentLoginSessionTable 1 } AgentLoginSessionEntry ::= SEQUENCE { agentLoginSessionIndex Integer32, agentLoginSessionUserName DisplayString, agentLoginSessionIPAddress IpAddress, agentLoginSessionConnectionType INTEGER, agentLoginSessionIdleTime TimeTicks, agentLoginSessionSessionTime TimeTicks, agentLoginSessionStatus RowStatus } agentLoginSessionIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session Index of the switch" ::= { agentLoginSessionEntry 1 } agentLoginSessionUserName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session UserName of the switch" ::= { agentLoginSessionEntry 2 } agentLoginSessionIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session IP Address of the switch" ::= { agentLoginSessionEntry 3 } agentLoginSessionConnectionType OBJECT-TYPE SYNTAX INTEGER { serial(1), telnet(2), web(3), ssl(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session Connection Type of the switch" ::= { agentLoginSessionEntry 4 } agentLoginSessionIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session Idle Time of the switch" ::= { agentLoginSessionEntry 5 } agentLoginSessionSessionTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session Time of the switch" ::= { agentLoginSessionEntry 6 } agentLoginSessionStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user." ::= { agentLoginSessionEntry 26 } --******************************************************************** -- agentTelnetConfigGroup --******************************************************************** agentTelnetConfigGroup OBJECT IDENTIFIER ::= {agentCLIConfigGroup 2} agentTelnetLoginTimeout OBJECT-TYPE SYNTAX Integer32 (0..160) MAX-ACCESS read-write STATUS current DESCRIPTION "Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 0 to 160. A value of 0 indicates that a Telnet session remains active indefinitely. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration." ::= { agentTelnetConfigGroup 1 } agentTelnetMaxSessions OBJECT-TYPE SYNTAX Integer32 (0..5) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established." ::= { agentTelnetConfigGroup 2 } agentTelnetAllowNewMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it. " ::= { agentTelnetConfigGroup 3 } agentSSHAllowNewMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Allow new SSH sessions (enable or disable) Config SSH disable means that no new SSH sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it." ::= { agentTelnetConfigGroup 4 } --******************************************************************** -- agentSerialGroup --******************************************************************** agentSerialGroup OBJECT IDENTIFIER ::= { agentCLIConfigGroup 5 } agentSerialTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Agent Serial Timeout " ::= { agentSerialGroup 1 } agentSerialBaudrate OBJECT-TYPE SYNTAX INTEGER { baud1200(1), baud2400(2), baud4800(3), baud9600(4), baud19200(5), baud38400(6), baud57600(7), baud115200(8) } MAX-ACCESS read-write STATUS current DESCRIPTION " Agent Serial Baudrate" ::= { agentSerialGroup 2 } agentSerialCharacterSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Agent Serial Character Size" ::= { agentSerialGroup 3 } agentSerialHWFlowControlMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " Agent Serial Hardware Flow Control." ::= { agentSerialGroup 4 } agentSerialStopBits OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Agent Serial Stop Bits" ::= { agentSerialGroup 5 } agentSerialParityType OBJECT-TYPE SYNTAX INTEGER { even(1), odd(2), none(3) } MAX-ACCESS read-only STATUS current DESCRIPTION " Agent Serial Parity Type" ::= { agentSerialGroup 6 } --******************************************************************* -- agentLagConfigGroup --******************************************************************** agentLagConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 2 } agentLagConfigCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Agent Lag Create. When this object is set with a non-empty string, a new lag will be created.if possible with the entered string as it's name." ::= { agentLagConfigGroup 1 } agentLagSummaryConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentLagSummaryConfigEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A summary table of the switch's lag config entries" ::= { agentLagConfigGroup 2 } agentLagSummaryConfigEntry OBJECT-TYPE SYNTAX AgentLagSummaryConfigEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "Switch's lag config entry" INDEX { agentLagSummaryName } ::= { agentLagSummaryConfigTable 1 } AgentLagSummaryConfigEntry ::= SEQUENCE { agentLagSummaryName DisplayString, agentLagSummaryLagIndex Integer32, agentLagSummaryFlushTimer Integer32, agentLagSummaryLinkTrap INTEGER, agentLagSummaryAdminMode INTEGER, agentLagSummaryStpMode INTEGER, agentLagSummaryAddPort Integer32, agentLagSummaryDeletePort Integer32, agentLagSummaryPortsBitMask Unsigned32, agentLagSummaryStatus RowStatus } agentLagSummaryName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Agent Lag Name" ::= { agentLagSummaryConfigEntry 1 } agentLagSummaryLagIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Agent Lag If Index" ::= { agentLagSummaryConfigEntry 2 } agentLagSummaryFlushTimer OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Agent Lag Flush Timer" ::= { agentLagSummaryConfigEntry 3 } agentLagSummaryLinkTrap OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Agent Lag Link Trap" ::= { agentLagSummaryConfigEntry 4 } agentLagSummaryAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Agent Lag Admin Mode" ::= { agentLagSummaryConfigEntry 5 } agentLagSummaryStpMode OBJECT-TYPE SYNTAX INTEGER { dot1d(1), fast(2), off(3) } MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Agent Lag STP Mode" ::= { agentLagSummaryConfigEntry 6 } agentLagSummaryAddPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Agent Lag Add Port. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any." ::= { agentLagSummaryConfigEntry 7 } agentLagSummaryDeletePort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Agent Lag Delete Port" ::= { agentLagSummaryConfigEntry 8 } agentLagSummaryPortsBitMask OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Agent Lag Member Ports in bit mask representation" ::= { agentLagSummaryConfigEntry 9 } agentLagSummaryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Agent Lag Status. active(1) - This Lag is enabled. destroy(6) - Set to this value to remove the Lag." ::= { agentLagSummaryConfigEntry 30 } --******************************************************************* -- agentLagDetailedConfigTable --******************************************************************* agentLagDetailedConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentLagDetailedConfigEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A detailed table of the switch's lag config entries" ::= { agentLagConfigGroup 3 } agentLagDetailedConfigEntry OBJECT-TYPE SYNTAX AgentLagDetailedConfigEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "Switch's lag config entry" INDEX { agentLagDetailedLagIndex, agentLagDetailedIfIndex } ::= { agentLagDetailedConfigTable 1 } AgentLagDetailedConfigEntry ::= SEQUENCE { agentLagDetailedLagIndex Integer32, agentLagDetailedIfIndex Integer32, agentLagDetailedPortSpeed OBJECT IDENTIFIER } agentLagDetailedLagIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Lag index" ::= { agentLagDetailedConfigEntry 1 } agentLagDetailedIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Lag port index" ::= { agentLagDetailedConfigEntry 2 } agentLagDetailedPortSpeed OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Lag port speed. See agentPortType for description and list of valid values." ::= { agentLagDetailedConfigEntry 22 } agentLagConfigMode OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The Lag Mode on the 4400 series controller. When it is on, all the gigabit ports are bound to one aggregated link." ::= { agentLagConfigGroup 4 } --******************************************************************** -- agentNetworkConfigGroup --******************************************************************** agentNetworkConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 3 } agentNetworkIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network ip address" ::= { agentNetworkConfigGroup 1 } agentNetworkSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network subnet mask" ::= { agentNetworkConfigGroup 2 } agentNetworkDefaultGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network default gateway" ::= { agentNetworkConfigGroup 3 } agentNetworkBurnedInMacAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Burned-In MAC address" ::= { agentNetworkConfigGroup 4 } agentNetworkConfigProtocol OBJECT-TYPE SYNTAX INTEGER { none(1), bootp(2), dhcp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network config protocol" ::= { agentNetworkConfigGroup 7 } agentNetworkWebMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's web access mode." ::= { agentNetworkConfigGroup 8 } agentNetworkSecureWebMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "If https is enable or not provided web mode is enabled" ::= { agentNetworkConfigGroup 9 } agentNetworkMulticastMode OBJECT-TYPE SYNTAX INTEGER { disable(0), unicast(1), multicast(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Switch's ethernet multicast support. disable- multicast is disabled multicast - Multicast is enabled. unicast- Controller will convert multicast to unicast packet." ::= { agentNetworkConfigGroup 10 } agentNetworkDsPortNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's distribution port number." ::= { agentNetworkConfigGroup 11 } agentNetworkUserIdleTimeout OBJECT-TYPE SYNTAX Unsigned32(10..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the idle user timeout." ::= { agentNetworkConfigGroup 12 } agentNetworkArpTimeout OBJECT-TYPE SYNTAX Unsigned32(10..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the ARP entry timeout." ::= { agentNetworkConfigGroup 13 } agentNetworkManagementVlan OBJECT-TYPE SYNTAX Unsigned32(0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN ID of the network management interface." ::= { agentNetworkConfigGroup 14 } agentNetworkGvrpStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The state of GVRP operation on the Switch. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.(Attribute No longer supported)" DEFVAL { enabled } ::= { agentNetworkConfigGroup 15 } agentNetworkAllowMgmtViaWireless OBJECT-TYPE SYNTAX INTEGER {enable(1),disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "This states whether Management via wireless is allowed or not." ::= { agentNetworkConfigGroup 16 } agentNetworkBroadcastSsidMode OBJECT-TYPE SYNTAX INTEGER {enable(1),disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "This mode when enabled allows WLAN SSIDs to be broadcasted." ::= { agentNetworkConfigGroup 17 } agentNetworkSecureWebPassword OBJECT-TYPE SYNTAX OCTET STRING(SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SSL Certificate Password. This can be optionally set while downloading SSL certificates of type Web Admin and Web Authentication" ::= { agentNetworkConfigGroup 18 } agentNetworkWebAdminCertType OBJECT-TYPE SYNTAX DisplayString (SIZE(1..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "Type of currently existing Web Admin Certificate installed on the Switch. It could be 'Empty' if the certificate is not present, 'Locally Generated' if the certificate is locally generated or it could have a name if it is downloaded externally." ::= { agentNetworkConfigGroup 19 } agentNetworkWebAdminCertRegenerateCmdInvoke OBJECT-TYPE SYNTAX INTEGER { default (0), activate (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This command when set to 'activate' will regenerate a Web Administration Certificate Locally that will replace the existing certificate." ::= { agentNetworkConfigGroup 20 } agentNetworkWebAuthCertType OBJECT-TYPE SYNTAX DisplayString (SIZE(1..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "Type of currently exisitng Web Authentication Certificate installed on the Switch. It could be 'Empty' if the certificate is not present, 'Locally Generated' if the certificate is locally generated or it could have a name if it is downloaded externally." ::= { agentNetworkConfigGroup 21 } agentNetworkWebAuthCertRegenerateCmdInvoke OBJECT-TYPE SYNTAX INTEGER { default (0), activate (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This command when set to 'activate' will regenerate a Web Authentication Certificate Locally that will replace the existing certificate." ::= { agentNetworkConfigGroup 22 } agentNetworkPeerToPeerBlockingMode OBJECT-TYPE SYNTAX INTEGER {enable(1),disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Mobile Peer to Peer Blocking mode on the switch." ::= { agentNetworkConfigGroup 24 } agentNetworkMulticastGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Multicast group address for access points." ::= { agentNetworkConfigGroup 25 } --******************************************************************** -- agentNeworkRouteTable --******************************************************************** agentNetworkRouteConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentNetworkRouteConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's Network Route entries" ::= { agentNetworkConfigGroup 23 } agentNetworkRouteConfigEntry OBJECT-TYPE SYNTAX AgentNetworkRouteConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's Network Route entry" INDEX {agentNetworkRouteIPAddress } ::= { agentNetworkRouteConfigTable 1 } AgentNetworkRouteConfigEntry ::= SEQUENCE { agentNetworkRouteIPAddress IpAddress, agentNetworkRouteIPNetmask IpAddress, agentNetworkRouteGateway IpAddress, agentNetworkRouteStatus RowStatus } agentNetworkRouteIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Network Route IP Address." ::= { agentNetworkRouteConfigEntry 1 } agentNetworkRouteIPNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION " Network Route IP Netmask." ::= { agentNetworkRouteConfigEntry 2 } agentNetworkRouteGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION " Network Route IP Gateway." ::= { agentNetworkRouteConfigEntry 3 } agentNetworkRouteStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Network Route Row Status." ::= { agentNetworkRouteConfigEntry 23 } --******************************************************************** -- agentInterfaceConfigTable --******************************************************************** agentInterfaceConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentInterfaceConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's Interface Config entries Typically, it will contain entries for Service Port Interface, DS Port Interface and Virtual Gateway Interface apart from other entries." ::= { agentConfigGroup 13 } agentInterfaceConfigEntry OBJECT-TYPE SYNTAX AgentInterfaceConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's Interface Config entry" INDEX { agentInterfaceName } ::= { agentInterfaceConfigTable 1 } AgentInterfaceConfigEntry ::= SEQUENCE { agentInterfaceName OCTET STRING, agentInterfaceVlanId Integer32, agentInterfaceType INTEGER, agentInterfaceMacAddress MacAddress, agentInterfaceIPAddress IpAddress, agentInterfaceIPNetmask IpAddress, agentInterfaceIPGateway IpAddress, agentInterfacePortNo Integer32, agentInterfaceActivePortNo Integer32, agentInterfaceBackupPortNo Integer32, agentInterfacePrimaryDhcpAddress IpAddress, agentInterfaceSecondaryDhcpAddress IpAddress, agentInterfaceDhcpProtocol INTEGER, agentInterfaceDnsHostName DisplayString, agentInterfaceAclName DisplayString, agentInterfaceAPManagementFeature INTEGER, agentInterfaceRowStatus RowStatus, agentInterfaceVlanQuarantine TruthValue } agentInterfaceName OBJECT-TYPE SYNTAX OCTET STRING(SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "Interace Name. This values is 'management' for DS port, 'service-port' for service port and 'virtual' for virtual gateway. For other interfaces, the name can be anything. These interfaces are already created by default." ::= { agentInterfaceConfigEntry 1 } agentInterfaceVlanId OBJECT-TYPE SYNTAX Integer32(0..4094) MAX-ACCESS read-create STATUS current DESCRIPTION "Vlan ID configured for the Interface." DEFVAL{ 0 } ::= { agentInterfaceConfigEntry 2 } agentInterfaceType OBJECT-TYPE SYNTAX INTEGER { static(0), dynamic(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The interface's type. The static type is set for the interfaces that are created by default on the switch and these cannot be deleted. Any other interface that is created is of type dynamic which can be deleted." ::= { agentInterfaceConfigEntry 3 } agentInterfaceMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Interface MAC Address. This is only applicable in case of management and service-port interfaces." ::= { agentInterfaceConfigEntry 4 } agentInterfaceIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of the interface." ::= { agentInterfaceConfigEntry 5 } agentInterfaceIPNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Netmask of the interface. This is 0 for the virtual interface." ::= { agentInterfaceConfigEntry 6 } agentInterfaceIPGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Gateway of the interface. This is 0 for virtual and service-port interface." ::= { agentInterfaceConfigEntry 7 } agentInterfacePortNo OBJECT-TYPE SYNTAX Integer32(0..25) MAX-ACCESS read-create STATUS current DESCRIPTION "A value 0 means the port is not set. The valid value can be any one of the physical ports on the switch. This is the primary port configured on the interface." DEFVAL{ 0 } ::= { agentInterfaceConfigEntry 8 } agentInterfacePrimaryDhcpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Primary DHCP Server IP Address for the interface This applies to the management interface and other dynamic interfaces." ::= { agentInterfaceConfigEntry 9 } agentInterfaceSecondaryDhcpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Secondary DHCP Server IP Address for the interface. This applies to the management interface and other dynamic interfaces." ::= { agentInterfaceConfigEntry 10 } agentInterfaceDhcpProtocol OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "The interface's DHCP protocol. This applies only to the service port interface." ::= { agentInterfaceConfigEntry 11 } agentInterfaceDnsHostName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-create STATUS current DESCRIPTION "The DNS host name for the Virtual Interface. This attribute is not valid for other interfaces." ::= { agentInterfaceConfigEntry 12 } agentInterfaceAclName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "Name of the Access Control List applied to the interface. This attribute is applicable only to the management interface and other dynamic interfaces. If it is required to remove the ACL name for an interface, it should be set to an empty string." ::= { agentInterfaceConfigEntry 13 } agentInterfaceAPManagementFeature OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "When enabled, the dynamic interface can be used for AP management. SNMP support for AP management through dynamic interfaces has been introduced since '3.0.21.0' release. Only applicable to dynamic interfaces in 4200 series. In static interfaces, 'disable' value 0 is returned. In 4000/3500 series of switches, 'disable' value 0 is returned." ::= { agentInterfaceConfigEntry 14 } agentInterfaceActivePortNo OBJECT-TYPE SYNTAX Integer32(0..25) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the currently active port for this interface." DEFVAL{ 0 } ::= { agentInterfaceConfigEntry 15 } agentInterfaceBackupPortNo OBJECT-TYPE SYNTAX Integer32(0..4) MAX-ACCESS read-create STATUS current DESCRIPTION "This values is valid only for the 4200 series of switches. The backup port is the port this interface is moved to once the primary port fails. A value 0 means the port is not set. The valid value can be any one of the physical ports on the 4200 switch." DEFVAL{ 0 } ::= { agentInterfaceConfigEntry 16 } agentInterfaceVlanQuarantine OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the health of the interface identified by agentInterfaceName. A value of 'true' is used to indicate that this particular interface is unhealthy. In this case, the data packets of the clients, that are assigned the VLAN Id corresponding to this interface, must be tunneled to the Controller by the REAP AP. A value of 'false' indicates that the VLAN configured against the interface is healthy and that the REAP AP can switch the clients of this VLAN locally rather than tunneling them to the Controller. " DEFVAL { false } ::= { agentInterfaceConfigEntry 17 } agentInterfaceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The interface entry Row status." ::= { agentInterfaceConfigEntry 31 } --******************************************************************** -- agentNtpConfigGroup - Configuration of Switch Network Time Protocol --******************************************************************** agentNtpConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 14 } agentNtpPollingInterval OBJECT-TYPE SYNTAX Integer32(3600..604800) MAX-ACCESS read-write STATUS current DESCRIPTION "Network Time Protocol polling interval. Min value is one hour and maximum is a week." ::= { agentNtpConfigGroup 1 } --******************************************************************** -- agentNtpServerTable - Configuration of Network Time Protocol Server --******************************************************************** agentNtpServerTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentNtpServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A summary table for switch's lag config entries" ::= { agentNtpConfigGroup 2 } agentNtpServerEntry OBJECT-TYPE SYNTAX AgentNtpServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's NTP Server entry. Upto 4 entries may be added." INDEX { agentNtpServerIndex } ::= { agentNtpServerTable 1 } AgentNtpServerEntry ::= SEQUENCE { agentNtpServerIndex Integer32, agentNtpServerAddress IpAddress, agentNtpServerRowStatus RowStatus } agentNtpServerIndex OBJECT-TYPE SYNTAX Integer32(1..3) MAX-ACCESS read-create STATUS current DESCRIPTION "NTP Server priority index." ::= { agentNtpServerEntry 1 } agentNtpServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of the NTP Server" ::= { agentNtpServerEntry 2 } agentNtpServerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "NTP server entry row status." ::= { agentNtpServerEntry 20 } --******************************************************************** -- agentDhcpConfigGroup - Configuration of Switch DHCP Server and -- its Scopes --******************************************************************** agentDhcpConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 15 } agentDhcpScopeTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpScopeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing the Scopes defined on the switch's DHCP Server." ::= { agentDhcpConfigGroup 1 } agentDhcpScopeEntry OBJECT-TYPE SYNTAX AgentDhcpScopeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's DHCP Server Scope entry." INDEX { agentDhcpScopeIndex } ::= { agentDhcpScopeTable 1 } AgentDhcpScopeEntry ::= SEQUENCE { agentDhcpScopeIndex Unsigned32, agentDhcpScopeName DisplayString, agentDhcpScopeLeaseTime Integer32, agentDhcpScopeNetwork IpAddress, agentDhcpScopeNetmask IpAddress, agentDhcpScopePoolStartAddress IpAddress, agentDhcpScopePoolEndAddress IpAddress, agentDhcpScopeDefaultRouterAddress1 IpAddress, agentDhcpScopeDefaultRouterAddress2 IpAddress, agentDhcpScopeDefaultRouterAddress3 IpAddress, agentDhcpScopeDnsDomainName DisplayString, agentDhcpScopeDnsServerAddress1 IpAddress, agentDhcpScopeDnsServerAddress2 IpAddress, agentDhcpScopeDnsServerAddress3 IpAddress, agentDhcpScopeNetbiosNameServerAddress1 IpAddress, agentDhcpScopeNetbiosNameServerAddress2 IpAddress, agentDhcpScopeNetbiosNameServerAddress3 IpAddress, agentDhcpScopeState INTEGER, agentDhcpScopeRowStatus RowStatus } agentDhcpScopeIndex OBJECT-TYPE SYNTAX Unsigned32(0..15) MAX-ACCESS read-create STATUS current DESCRIPTION "DHCP Scope Identifier Index." ::= { agentDhcpScopeEntry 1 } agentDhcpScopeName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..79)) MAX-ACCESS read-create STATUS current DESCRIPTION "DHCP Scope Name." ::= { agentDhcpScopeEntry 2 } agentDhcpScopeLeaseTime OBJECT-TYPE SYNTAX Integer32(120..8640000) MAX-ACCESS read-create STATUS current DESCRIPTION "DHCP Scope Lease time in seconds." ::= { agentDhcpScopeEntry 3 } agentDhcpScopeNetwork OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of the DHCP Scope Network. This is the address which is used to determine the DHCP scope a remote Switch is attaching to." ::= { agentDhcpScopeEntry 4 } agentDhcpScopeNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The DHCP Scope Netmask. This the subnet mask for the address pool." ::= { agentDhcpScopeEntry 5 } agentDhcpScopePoolStartAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The DHCP Scope address pool start IP address." ::= { agentDhcpScopeEntry 6 } agentDhcpScopePoolEndAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The DHCP Scope address pool end IP address." ::= { agentDhcpScopeEntry 7 } agentDhcpScopeDefaultRouterAddress1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of the DHCP Scope's default Router 1." ::= { agentDhcpScopeEntry 8 } agentDhcpScopeDefaultRouterAddress2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of the DHCP Scope's default Router 2." ::= { agentDhcpScopeEntry 9 } agentDhcpScopeDefaultRouterAddress3 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of the DHCP Scope's default Router 3." ::= { agentDhcpScopeEntry 10 } agentDhcpScopeDnsDomainName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..79)) MAX-ACCESS read-create STATUS current DESCRIPTION "DNS Domain name for the DHCP Scope." ::= { agentDhcpScopeEntry 11 } agentDhcpScopeDnsServerAddress1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of the DHCP Scope's DNS Server 1." ::= { agentDhcpScopeEntry 12 } agentDhcpScopeDnsServerAddress2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of the DHCP Scope's DNS Server 2." ::= { agentDhcpScopeEntry 13 } agentDhcpScopeDnsServerAddress3 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of the DHCP Scope's DNS Server 3." ::= { agentDhcpScopeEntry 14 } agentDhcpScopeNetbiosNameServerAddress1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of DHCP Scope's Netbios Name Server 1." ::= { agentDhcpScopeEntry 15 } agentDhcpScopeNetbiosNameServerAddress2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of DHCP Scope's Netbios Name Server 2." ::= { agentDhcpScopeEntry 16 } agentDhcpScopeNetbiosNameServerAddress3 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP Address of DHCP Scope's Netbios Name Server 3." ::= { agentDhcpScopeEntry 17 } agentDhcpScopeState OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "DHCP Scope's State." ::= { agentDhcpScopeEntry 18 } agentDhcpScopeRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Dhcp Scope entry row status." ::= { agentDhcpScopeEntry 30 } --******************************************************************** -- agentServicePortConfigGroup -- (Interface of type service-port in agentInterfaceConfigTable -- use is recommended instead of this group.) --******************************************************************** agentServicePortConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 4 } agentServicePortIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The switch's Service Port IP address. (Service-port interface use is recommended instead of this group)" ::= { agentServicePortConfigGroup 1 } agentServicePortSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The switch's Service Port subnet mask. (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)" ::= { agentServicePortConfigGroup 2 } agentServicePortDefaultGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Not Supported for release 1.0. The switch's Service Port default gateway. (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)" ::= { agentServicePortConfigGroup 3 } agentServicePortBurnedInMacAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The switch's Service Port Burned-In MAC address (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)" ::= { agentServicePortConfigGroup 4 } agentServicePortConfigProtocol OBJECT-TYPE SYNTAX INTEGER { none(1), dhcp(3) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The switch's Service Port config protocol (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)" ::= { agentServicePortConfigGroup 5 } --******************************************************************** -- agentSnmpConfigGroup --******************************************************************** agentSnmpConfigGroup OBJECT IDENTIFIER ::= {agentConfigGroup 5} agentSnmpTrapPortNumber OBJECT-TYPE SYNTAX Unsigned32(1..65534) MAX-ACCESS read-write STATUS current DESCRIPTION "Snmp Trap Port Number" ::= { agentSnmpConfigGroup 1 } agentSnmpVersion1Status OBJECT-TYPE SYNTAX INTEGER{disable(0),enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Snmp Version 1 Status" ::= { agentSnmpConfigGroup 2 } agentSnmpVersion2cStatus OBJECT-TYPE SYNTAX INTEGER{disable(0),enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Snmp Version 2c Status" ::= { agentSnmpConfigGroup 3 } --******************************************************************** -- agentSnmpCommunityConfigTable --******************************************************************** agentSnmpCommunityConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSnmpCommunityConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's SNMP community Config entries" ::= { agentSnmpConfigGroup 5 } agentSnmpCommunityConfigEntry OBJECT-TYPE SYNTAX AgentSnmpCommunityConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's SNMP community Config entry" INDEX {agentSnmpCommunityName } ::= { agentSnmpCommunityConfigTable 1 } AgentSnmpCommunityConfigEntry ::= SEQUENCE { agentSnmpCommunityName DisplayString, agentSnmpCommunityIPAddress IpAddress, agentSnmpCommunityIPMask IpAddress, agentSnmpCommunityAccessMode INTEGER, agentSnmpCommunityEnabled INTEGER, agentSnmpCommunityStatus RowStatus } agentSnmpCommunityName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored. " ::= { agentSnmpCommunityConfigEntry 1 } agentSnmpCommunityIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses." ::= { agentSnmpCommunityConfigEntry 2 } agentSnmpCommunityIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255." ::= { agentSnmpCommunityConfigEntry 3 } agentSnmpCommunityAccessMode OBJECT-TYPE SYNTAX INTEGER { readOnly(1), readWrite(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The switch's Snmp Community Access Mode Access Mode - This value can be readOnly or readWrite. A community with a read-only access allows for switch information to be displayed. A community with a readWrite access allows for configuration changes to be made and for information to be displayed. " DEFVAL {readOnly} ::= { agentSnmpCommunityConfigEntry 4 } agentSnmpCommunityEnabled OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "If community is Enabled " DEFVAL { no } ::= { agentSnmpCommunityConfigEntry 5 } agentSnmpCommunityStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP manager associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent." ::= { agentSnmpCommunityConfigEntry 25 } --******************************************************************** -- agentSnmpTrapReceiverConfigTable --******************************************************************** agentSnmpTrapReceiverConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSnmpTrapReceiverConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported." ::= { agentSnmpConfigGroup 6 } agentSnmpTrapReceiverConfigEntry OBJECT-TYPE SYNTAX AgentSnmpTrapReceiverConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's Snmp Trap Receiver Config entry" INDEX { agentSnmpTrapReceiverName } ::= { agentSnmpTrapReceiverConfigTable 1 } AgentSnmpTrapReceiverConfigEntry ::= SEQUENCE { agentSnmpTrapReceiverName OCTET STRING, agentSnmpTrapReceiverIPAddress IpAddress, agentSnmpTrapReceiverEnabled INTEGER, agentSnmpTrapReceiverStatus RowStatus } agentSnmpTrapReceiverName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The switch's Snmp Trap Receiver Name. This is the name of the remote network manager. the name can be up to 16 characters, and is case-sensitive." ::= { agentSnmpTrapReceiverConfigEntry 1 } agentSnmpTrapReceiverIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "SNMP network Manager IP Address. The IP Address traps will be sent to. Each IP address parameter is four integer numbers. The numbers range from 0 to 255. After creation of entry IP Address cannot be changed." ::= { agentSnmpTrapReceiverConfigEntry 2 } agentSnmpTrapReceiverEnabled OBJECT-TYPE SYNTAX INTEGER{no(0),yes(1)} MAX-ACCESS read-create STATUS current DESCRIPTION "The flag to enable the trap receiver. If disabled, no traps are sent to this receiver's IP Address. " DEFVAL{ no } ::= { agentSnmpTrapReceiverConfigEntry 3 } agentSnmpTrapReceiverStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create and delete instances of this table. The row, when created with the row status value of 'createAndGo' or 'createAndWait' is moved to the 'active' state automatically by the agent and remains in that state till the time the row is removed through the 'destroy' option." ::= { agentSnmpTrapReceiverConfigEntry 23 } --******************************************************************** -- agentSnmpTrapFlagsConfigGroup --******************************************************************** agentSnmpTrapFlagsConfigGroup OBJECT IDENTIFIER ::= { agentSnmpConfigGroup 7 } agentSnmpAuthenticationTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication Flag - Enable/Disable authentication Flag." ::= { agentSnmpTrapFlagsConfigGroup 1 } agentSnmpLinkUpDownTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable." ::= { agentSnmpTrapFlagsConfigGroup 2 } agentSnmpMultipleUsersTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session" ::= { agentSnmpTrapFlagsConfigGroup 3 } agentSnmpSpanningTreeTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps." ::= { agentSnmpTrapFlagsConfigGroup 4 } agentSnmpBroadcastStormTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery." ::= { agentSnmpTrapFlagsConfigGroup 5 } --******************************************************************** -- agentSnmpV3ConfigGroup --******************************************************************** agentSnmpV3ConfigGroup OBJECT IDENTIFIER ::= {agentConfigGroup 6} agentSnmpVersion3Status OBJECT-TYPE SYNTAX INTEGER{disable(0),enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Snmp Version 3 Status" ::= { agentSnmpV3ConfigGroup 1 } --******************************************************************** -- agentSnmpV3UserConfigTable --******************************************************************** agentSnmpV3UserConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSnmpV3UserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Config Table. Only creation and deletion of users is supported. All individual updates are not supported." ::= { agentSnmpV3ConfigGroup 2 } agentSnmpV3UserConfigEntry OBJECT-TYPE SYNTAX AgentSnmpV3UserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Config Entry" INDEX { agentSnmpV3UserName } ::= { agentSnmpV3UserConfigTable 1 } AgentSnmpV3UserConfigEntry ::= SEQUENCE { agentSnmpV3UserName OCTET STRING, agentSnmpV3UserAccessMode INTEGER, agentSnmpV3UserAuthenticationType INTEGER, agentSnmpV3UserEncryptionType INTEGER, agentSnmpV3UserAuthenticationPassword OCTET STRING, agentSnmpV3UserEncryptionPassword OCTET STRING, agentSnmpV3UserStatus RowStatus } agentSnmpV3UserName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "Agent User Name." ::= { agentSnmpV3UserConfigEntry 1 } agentSnmpV3UserAccessMode OBJECT-TYPE SYNTAX INTEGER { readonly(1), readwrite(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Agent User Access Mode" ::= { agentSnmpV3UserConfigEntry 2 } agentSnmpV3UserAuthenticationType OBJECT-TYPE SYNTAX INTEGER { none(1), hmacmd5(2), hmacsha(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "SNMPv3 User Authentication none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication" ::= { agentSnmpV3UserConfigEntry 3 } agentSnmpV3UserEncryptionType OBJECT-TYPE SYNTAX INTEGER { none(1), des(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "SNMPv3 User Encryption Must be set to none(1) if agentSnmpV3UserAuthenticationType is set to none(1). Setting this object will set the encryption password to an empty string. none(1) - no encryption used des(1) - DES encryption used" ::= { agentSnmpV3UserConfigEntry 4 } agentSnmpV3UserAuthenticationPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "SNMPv3 User Encryption Password" ::= { agentSnmpV3UserConfigEntry 5 } agentSnmpV3UserEncryptionPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "SNMPv3 User Encryption Password" ::= { agentSnmpV3UserConfigEntry 6 } agentSnmpV3UserStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account." ::= { agentSnmpV3UserConfigEntry 26 } --******************************************************************** -- agentSpanningTreePortTable --******************************************************************** agentSpanningTreeConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 7 } agentSpanningTreeMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Spanning Tree Switch Status" ::= { agentSpanningTreeConfigGroup 1 } --******************************************************************** -- agentSwitchConfigGroup --******************************************************************** agentSwitchConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 8 } agentSwitchAddressAgingTimeoutTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchAddressAgingTimeoutEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch's address aging timeout table" ::= { agentSwitchConfigGroup 4 } agentSwitchAddressAgingTimeoutEntry OBJECT-TYPE SYNTAX AgentSwitchAddressAgingTimeoutEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Aging information about a specific Filtering Database." INDEX { dot1qFdbId } ::= { agentSwitchAddressAgingTimeoutTable 1 } AgentSwitchAddressAgingTimeoutEntry ::= SEQUENCE { agentSwitchAddressAgingTimeout Integer32 } agentSwitchAddressAgingTimeout OBJECT-TYPE SYNTAX Integer32 (10..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The FDB entry's address aging timeout(in seconds)" DEFVAL { 300 } ::= { agentSwitchAddressAgingTimeoutEntry 10 } agentSwitchBroadcastControlMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds 20 percent of the link speed, the switch blocks (discards) the broadcast traffic until the broadcast traffic returns to 10 percent or less.Upper limit for 10M link is 20% and lower limit is 10%. For 100M link Upper limit is 5% and lower limit is 2%" ::= { agentSwitchConfigGroup 2 } agentSwitchDot3FlowControlMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports. " ::= { agentSwitchConfigGroup 3 } agentSwitchLwappTransportMode OBJECT-TYPE SYNTAX INTEGER { layer2(1), layer3(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The LWAPP transport mode decides if the switch is operating in the Layer2 or Layer3 mode. The switch needs to be rebooted for the mode change to take effect." ::= { agentSwitchConfigGroup 5 } --******************************************************************** -- agentTransferConfigGroup --******************************************************************** agentTransferConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 9 } --******************************************************************* -- agentTransferUploadGroup --******************************************************************* agentTransferUploadGroup OBJECT IDENTIFIER ::= { agentTransferConfigGroup 1 } agentTransferUploadMode OBJECT-TYPE SYNTAX INTEGER { tftp(1), xmodem(2), ymodem(3), zmodem(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port." ::= { agentTransferUploadGroup 1 } agentTransferUploadServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload tftpserverip configures the IP address of the server where the file will be uploaded. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255." ::= { agentTransferUploadGroup 2 } agentTransferUploadPath OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload tftppath configures the directory path where the file is to be uploaded to. The switch remembers the last file path used." ::= { agentTransferUploadGroup 3 } agentTransferUploadFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload tftpfilename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP." ::= { agentTransferUploadGroup 4 } agentTransferUploadDataType OBJECT-TYPE SYNTAX INTEGER { config(2), errorlog(3), systemtrace(4), traplog(5), crashfile(6), signatures(7), unknown(99) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - System trace - Trap log - Crash File " ::= { agentTransferUploadGroup 5 } agentTransferUploadStart OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload start will start an upload transfer. The agentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP." ::= { agentTransferUploadGroup 6 } agentTransferUploadStatus OBJECT-TYPE SYNTAX INTEGER { notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13), unknown(99) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current status of an upload transfer." ::= { agentTransferUploadGroup 7 } agentTransferConfigurationFileEncryption OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The configuration file can be encrypted before tftp upload from the switch and then decrypted before downloading to the switch when this option is enabled." ::= { agentTransferConfigGroup 3 } agentTransferConfigurationFileEncryptionKey OBJECT-TYPE SYNTAX DisplayString(SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the key to be used when encrypting the configuration file while upload from the switch or while decrypting the file after download to the switch." ::= { agentTransferConfigGroup 4 } --******************************************************************** -- agentTransferDownloadGroup --******************************************************************** agentTransferDownloadGroup OBJECT IDENTIFIER ::= { agentTransferConfigGroup 2 } agentTransferDownloadMode OBJECT-TYPE SYNTAX INTEGER { tftp(1), xmodem(2), ymodem(3), zmodem(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port." ::= { agentTransferDownloadGroup 1 } agentTransferDownloadServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255." ::= { agentTransferDownloadGroup 2 } agentTransferDownloadPath OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download tftppath configures the directory path where the file is located. The switch remembers the last file path used." ::= { agentTransferDownloadGroup 3 } agentTransferDownloadFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download tftpfilename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP." ::= { agentTransferDownloadGroup 4 } agentTransferDownloadDataType OBJECT-TYPE SYNTAX INTEGER { code(2), config(3), webauthcert(4), webadmincert(5), signatures(6), customWebAuth(7), unknown(99) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download datatype configures the type of file to downloaded to the switch. The types for download are: - Code - Configuration - Certificates - Signatures - customWebauth- custom webauth tar ball" ::= { agentTransferDownloadGroup 5 } agentTransferDownloadStart OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP." ::= { agentTransferDownloadGroup 6 } agentTransferDownloadStatus OBJECT-TYPE SYNTAX INTEGER { notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13), bootBreakOff(14), invalidTarFile(15), unknown(99) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current status of an download transfer." ::= { agentTransferDownloadGroup 7 } agentTransferDownloadTftpMaxRetries OBJECT-TYPE SYNTAX Unsigned32(1..254) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of retries to be allowed for a TFTP message packet." DEFVAL{ 10 } ::= { agentTransferDownloadGroup 8 } agentTransferDownloadTftpTimeout OBJECT-TYPE SYNTAX Unsigned32(1..254) MAX-ACCESS read-write STATUS current DESCRIPTION "Timeout in seconds for a TFTP message packet." DEFVAL{ 6 } ::= { agentTransferDownloadGroup 9 } --******************************************************************** -- agentDot3adAggPortTable --******************************************************************** agentDot3adAggPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDot3adAggPortEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB." ::= { agentConfigGroup 11 } agentDot3adAggPortEntry OBJECT-TYPE SYNTAX AgentDot3adAggPortEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port." INDEX { agentDot3adAggPort } ::= { agentDot3adAggPortTable 1 } AgentDot3adAggPortEntry ::= SEQUENCE { agentDot3adAggPort Integer32, agentDot3adAggPortLACPMode INTEGER } agentDot3adAggPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "ifIndex of this physical port" ::= { agentDot3adAggPortEntry 1 } agentDot3adAggPortLACPMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Enable/disable 802.3ad LACP on this port" ::= { agentDot3adAggPortEntry 21 } --******************************************************************** -- agentPortConfigTable -- --******************************************************************** agentPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's physical port config entries" ::= { agentConfigGroup 12 } agentPortConfigEntry OBJECT-TYPE SYNTAX AgentPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's physical port config entry" INDEX { agentPortDot1dBasePort } ::= { agentPortConfigTable 1 } AgentPortConfigEntry ::= SEQUENCE { agentPortDot1dBasePort Integer32, agentPortIfIndex Integer32, agentPortIanaType IANAifType, agentPortSTPMode INTEGER, agentPortSTPState INTEGER, agentPortAdminMode INTEGER, agentPortPhysicalMode INTEGER, agentPortPhysicalStatus INTEGER, agentPortLinkTrapMode INTEGER, agentPortClearStats INTEGER, agentPortDefaultType OBJECT IDENTIFIER, agentPortType OBJECT IDENTIFIER, agentPortAutoNegAdminStatus INTEGER, agentPortDot3FlowControlMode INTEGER, agentPortPowerMode INTEGER, agentPortGvrpStatus INTEGER, agentPortGarpJoinTime Unsigned32, agentPortGarpLeaveTime Unsigned32, agentPortGarpLeaveAllTime Unsigned32, agentPortMirrorMode INTEGER, agentPortMulticastApplianceMode INTEGER, agentPortOperationalStatus INTEGER } agentPortDot1dBasePort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of this port." ::= { agentPortConfigEntry 1 } agentPortIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Port IfIndex" ::= { agentPortConfigEntry 2 } agentPortIanaType OBJECT-TYPE SYNTAX IANAifType MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Port Type" ::= { agentPortConfigEntry 3 } agentPortSTPMode OBJECT-TYPE SYNTAX INTEGER { dot1d(1), fast(2), off(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port" ::= { agentPortConfigEntry 4 } agentPortSTPState OBJECT-TYPE SYNTAX INTEGER { blocking(1), listening(2), learning(3), forwarding(4), disabled(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Port Spanning Tree Protocol State" ::= { agentPortConfigEntry 5 } agentPortAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Port Admin Mode" ::= { agentPortConfigEntry 6 } agentPortPhysicalMode OBJECT-TYPE SYNTAX INTEGER { autoNegotiate(1), half10(2), full10(3), half100(4), full100(5), full1000sx(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Port Speed Mode. This is the configured physical mode.This object is read-only for gigabit ports" ::= { agentPortConfigEntry 7 } agentPortPhysicalStatus OBJECT-TYPE SYNTAX INTEGER { autonegotiate(1), half10(2), full10(3), half100(4), full100(5), full1000sx(8), unknown(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Port Physical Speed Status.This is the current actual speed." ::= { agentPortConfigEntry 8 } agentPortLinkTrapMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "If enabled, link up and link down traps will be sent for this port." ::= { agentPortConfigEntry 9 } agentPortClearStats OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear stats for this port only" ::= { agentPortConfigEntry 10 } agentPortDefaultType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of possible values for this object is the same as the set defined for the agentPortType object. This object represents the administratively- configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD" REFERENCE "RFC 2668" ::= { agentPortConfigEntry 11 } agentPortType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object qbEnetDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object qbEnetPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD" REFERENCE "RFC 2668" ::= { agentPortConfigEntry 12 } agentPortAutoNegAdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the administration status of auto negotiation for this port." ::= { agentPortConfigEntry 13 } agentPortDot3FlowControlMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports." ::= { agentPortConfigEntry 14 } agentPortPowerMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0) } MAX-ACCESS read-write STATUS current DESCRIPTION " Enable/Disable the port's Power over ethernet. This doesn't apply to appliances that have no POE controller." ::= { agentPortConfigEntry 15 } agentPortGvrpStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.(Attribute no longer supported)" DEFVAL { enabled } ::= { agentPortConfigEntry 16 } agentPortGarpJoinTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The GARP Join time, in centiseconds.(Attribute no longer supported)" DEFVAL { 20 } ::= { agentPortConfigEntry 17 } agentPortGarpLeaveTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The GARP Leave time, in centiseconds.(Attribute no longer supported)" DEFVAL { 60 } ::= { agentPortConfigEntry 18 } agentPortGarpLeaveAllTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The GARP LeaveAll time, in centiseconds.(Attribute no longer supported)" DEFVAL { 1000 } ::= { agentPortConfigEntry 19 } agentPortMirrorMode OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Port Mirror Mode. If enabled, then this is the port that the packets are mirrored to." ::= { agentPortConfigEntry 20 } agentPortMulticastApplianceMode OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Port Multicast Appliance Mode. If enabled, then this port allows multicast streams through it. At a time, a maximum of four ports including the gigabit ethernet port can have this mode enabled on them. This is to limit the number of multicast streams allowed through the switch at a given time." ::= { agentPortConfigEntry 21 } agentPortOperationalStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of the port." ::= { agentPortConfigEntry 40 } --******************************************************************** -- agentSystemGroup --******************************************************************** agentSaveConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "save config to NVRAM" ::= { agentSystemGroup 1 } agentClearConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear config to factory defaults" ::= { agentSystemGroup 2 } agentClearLags OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear lag configuration" ::= { agentSystemGroup 3 } agentClearLoginSessions OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "close all telnet sessions" ::= { agentSystemGroup 4 } agentClearPortStats OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear all port statistics" ::= { agentSystemGroup 6 } agentClearSwitchStats OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear all switch statistics" ::= { agentSystemGroup 7 } agentClearTrapLog OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear trap log" ::= { agentSystemGroup 8 } agentResetSystem OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "reset the switch" ::= { agentSystemGroup 10 } --******************************************************************** -- portStatsTable -- Enterprise portion of Ethernet Statistics Group -- This augments the etherStatsTable of RMON group. --******************************************************************** portStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF PortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of additional thernet statistics entries." ::= { stats 1 } portStatsEntry OBJECT-TYPE SYNTAX PortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A collection of statistics kept for a particular Ethernet interface." INDEX { portStatsIndex } ::= { portStatsTable 1 } PortStatsEntry ::= SEQUENCE { portStatsIndex Integer32, portStatsPktsTx64Octets Counter32, portStatsPktsTx65to127Octets Counter32, portStatsPktsTx128to255Octets Counter32, portStatsPktsTx256to511Octets Counter32, portStatsPktsTx512to1023Octets Counter32, portStatsPktsTx1024to1518Octets Counter32, portStatsPktsRx1519to1530Octets Counter32, portStatsPktsTx1519to1530Octets Counter32, portStatsPktsTxOversizeOctets Counter32 } portStatsIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object uniquely identifies this portStatsEntry." ::= { portStatsEntry 1 } portStatsPktsTx64Octets OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets (including bad packets) transmitted that were 64 octets in length (excluding framing bits but including FCS octets)." ::= { portStatsEntry 2 } portStatsPktsTx65to127Octets OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets (including bad packets) transmitted that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets)." ::= { portStatsEntry 3 } portStatsPktsTx128to255Octets OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets (including bad packets) transmitted that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets)." ::= { portStatsEntry 4 } portStatsPktsTx256to511Octets OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets (including bad packets) transmitted that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets)." ::= { portStatsEntry 5 } portStatsPktsTx512to1023Octets OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets (including bad packets) transmitted that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets)." ::= { portStatsEntry 6 } portStatsPktsTx1024to1518Octets OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets (including bad packets) transmitted that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets)." ::= { portStatsEntry 7 } portStatsPktsRx1519to1530Octets OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets (including bad packets) received that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets)." ::= { portStatsEntry 8 } portStatsPktsTx1519to1530Octets OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets (including bad packets) transmitted that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets)." ::= { portStatsEntry 9 } portStatsPktsTxOversizeOctets OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets (including bad packets) transmitted that were more than 1530 octets in length. (excluding framing bits but including FCS octets)." ::= { portStatsEntry 30 } --******************************************************************** -- switchingTraps --******************************************************************** multipleUsersTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Multiple Users Log Trap." ::= { switchingTraps 1 } broadcastStormStartTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Broadcast Storm Start Log Trap." ::= { switchingTraps 2 } broadcastStormEndTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Broadcast Storm End Log Trap." ::= { switchingTraps 3 } linkFailureTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "trapMgrLinkFailureLogTrap." ::= { switchingTraps 4 } vlanRequestFailureTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS current DESCRIPTION "Vlan Request Failure Log Trap" ::= { switchingTraps 5 } vlanDeleteLastTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS current DESCRIPTION "Last Vlan Delete Log Trap" ::= { switchingTraps 6 } vlanDefaultCfgFailureTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS current DESCRIPTION "Default Vlan Config Failure Log Trap" ::= { switchingTraps 7 } vlanRestoreFailureTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS current DESCRIPTION "Vlan Restore Failure Log Trap" ::= { switchingTraps 8 } fanFailureTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Fan Failure Log Trap." ::= { switchingTraps 9 } stpInstanceNewRootTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS current DESCRIPTION "STP Instance New Root Trap" ::= { switchingTraps 10 } stpInstanceTopologyChangeTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS current DESCRIPTION "STP Instance Topology Change Trap" ::= { switchingTraps 11 } powerSupplyStatusChangeTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Power Supply Status Change Trap" ::= { switchingTraps 12 } --******************************************************************** --* Compliance statements --******************************************************************** bsnSwitchingCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMP entities that implement the bsnSwitching module" MODULE MANDATORY-GROUPS { bsnSwitchingAgentInfoGroup, bsnSwitchingAgentConfigGroup, bsnSwitchingAgentSystemGroup, bsnSwitchingAgentStatsGroup } ::= { bsnSwitchingCompliances 1 } --******************************************************************** --* Units of conformance --******************************************************************** bsnSwitchingAgentInfoGroup OBJECT-GROUP OBJECTS { agentInventorySysDescription, agentInventoryMachineType, agentInventoryMachineModel, agentInventorySerialNumber, agentInventoryMaintenanceLevel, agentInventoryBurnedInMacAddress, agentInventoryOperatingSystem, agentInventoryManufacturerName, agentInventoryProductName, agentInventoryProductVersion, agentInventoryIsGigECardPresent, agentInventoryIsCryptoCardPresent, agentInventoryIsForeignAPSupported, agentInventoryMaxNumberOfAPsSupported, agentInventoryIsCryptoCard2Present, agentInventoryFipsModeEnabled, agentTrapLogTotal, agentTrapLogTotalSinceLastViewed, agentTrapLogIndex, agentTrapLogSystemTime, agentTrapLogTrap, agentRadioUpDownTrapCount, agentApAssociateDisassociateTrapCount, agentApLoadProfileFailTrapCount, agentApNoiseProfileFailTrapCount, agentApInterferenceProfileFailTrapCount, agentApCoverageProfileFailTrapCount, agentSwitchInfoLwappTransportMode, agentSwitchInfoPowerSupply1Present, agentSwitchInfoPowerSupply1Operational, agentSwitchInfoPowerSupply2Present, agentSwitchInfoPowerSupply2Operational, agentCurrentCPUUtilization, agentTotalMemory, agentFreeMemory, agentWcpDeviceName, agentWcpSlotNumber, agentWcpPortNumber, agentWcpPeerPortNumber, agentWcpPeerIpAddress, agentWcpControllerTableChecksum, agentWcpControllerInfoSlotNumber, agentWcpControllerInfoPortNumber, agentWcpControllerInfoIpAddress } STATUS current DESCRIPTION "This collection of objects provide switching information." ::= { bsnSwitchingGroups 1} bsnSwitchingAgentConfigGroup OBJECT-GROUP OBJECTS { agentLoginSessionIndex, agentLoginSessionUserName, agentLoginSessionIPAddress, agentLoginSessionConnectionType, agentLoginSessionIdleTime, agentLoginSessionSessionTime, agentLoginSessionStatus, agentTelnetLoginTimeout, agentTelnetMaxSessions, agentTelnetAllowNewMode, agentSSHAllowNewMode, agentSerialTimeout, agentSerialBaudrate, agentSerialCharacterSize, agentSerialHWFlowControlMode, agentSerialStopBits, agentSerialParityType, agentNetworkIPAddress, agentNetworkSubnetMask, agentNetworkDefaultGateway, agentNetworkBurnedInMacAddress, agentNetworkConfigProtocol, agentNetworkWebMode, agentNetworkSecureWebMode, agentNetworkMulticastMode, agentNetworkDsPortNumber, agentNetworkUserIdleTimeout, agentNetworkArpTimeout, agentNetworkManagementVlan, agentNetworkAllowMgmtViaWireless, agentNetworkBroadcastSsidMode, agentNetworkSecureWebPassword, agentNetworkWebAdminCertType, agentNetworkWebAuthCertRegenerateCmdInvoke, agentNetworkWebAdminCertRegenerateCmdInvoke, agentNetworkWebAuthCertType, agentNetworkRouteIPAddress, agentNetworkRouteIPNetmask, agentNetworkRouteGateway, agentNetworkRouteStatus, agentNetworkPeerToPeerBlockingMode, agentNetworkMulticastGroupAddress, agentInterfaceName, agentInterfaceVlanId, agentInterfaceType, agentInterfaceMacAddress, agentInterfaceIPAddress, agentInterfaceIPNetmask, agentInterfaceIPGateway, agentInterfacePortNo, agentInterfacePrimaryDhcpAddress, agentInterfaceSecondaryDhcpAddress, agentInterfaceDhcpProtocol, agentInterfaceDnsHostName, agentInterfaceAclName, agentInterfaceAPManagementFeature, agentInterfaceActivePortNo, agentInterfaceBackupPortNo, agentInterfaceVlanQuarantine, agentInterfaceRowStatus, agentNtpPollingInterval, agentNtpServerIndex, agentNtpServerAddress, agentNtpServerRowStatus, agentDhcpScopeIndex, agentDhcpScopeName, agentDhcpScopeLeaseTime, agentDhcpScopeNetwork, agentDhcpScopeNetmask, agentDhcpScopePoolStartAddress, agentDhcpScopePoolEndAddress, agentDhcpScopeDefaultRouterAddress1, agentDhcpScopeDefaultRouterAddress2, agentDhcpScopeDefaultRouterAddress3, agentDhcpScopeDnsDomainName, agentDhcpScopeDnsServerAddress1, agentDhcpScopeDnsServerAddress2, agentDhcpScopeDnsServerAddress3, agentDhcpScopeNetbiosNameServerAddress1, agentDhcpScopeNetbiosNameServerAddress2, agentDhcpScopeNetbiosNameServerAddress3, agentDhcpScopeState, agentDhcpScopeRowStatus, agentSnmpTrapPortNumber, agentSnmpVersion1Status, agentSnmpVersion2cStatus, agentSnmpCommunityName, agentSnmpCommunityIPAddress, agentSnmpCommunityIPMask, agentSnmpCommunityAccessMode, agentSnmpCommunityEnabled, agentSnmpCommunityStatus, agentSnmpTrapReceiverName, agentSnmpTrapReceiverIPAddress, agentSnmpTrapReceiverEnabled, agentSnmpTrapReceiverStatus, agentSnmpAuthenticationTrapFlag, agentSnmpLinkUpDownTrapFlag, agentSnmpMultipleUsersTrapFlag, agentSnmpSpanningTreeTrapFlag, agentSnmpVersion3Status, agentSnmpV3UserName, agentSnmpV3UserAccessMode, agentSnmpV3UserAuthenticationType, agentSnmpV3UserEncryptionType, agentSnmpV3UserAuthenticationPassword, agentSnmpV3UserEncryptionPassword, agentSnmpV3UserStatus, agentSpanningTreeMode, agentSwitchAddressAgingTimeout, agentSwitchBroadcastControlMode, agentSwitchDot3FlowControlMode, agentSwitchLwappTransportMode, agentTransferUploadMode, agentTransferUploadServerIP, agentTransferUploadPath, agentTransferUploadFilename, agentTransferUploadDataType, agentTransferUploadStart, agentTransferUploadStatus, agentTransferConfigurationFileEncryption, agentTransferConfigurationFileEncryptionKey, agentTransferDownloadMode, agentTransferDownloadServerIP, agentTransferDownloadPath, agentTransferDownloadFilename, agentTransferDownloadDataType, agentTransferDownloadStart, agentTransferDownloadStatus, agentTransferDownloadTftpMaxRetries, agentTransferDownloadTftpTimeout, agentPortDot1dBasePort, agentPortIfIndex, agentPortIanaType, agentPortSTPMode, agentPortSTPState, agentPortAdminMode, agentPortPhysicalMode, agentPortPhysicalStatus, agentPortLinkTrapMode, agentPortClearStats, agentPortDefaultType, agentPortType, agentPortAutoNegAdminStatus, agentPortDot3FlowControlMode, agentPortPowerMode, agentPortMirrorMode, agentPortMulticastApplianceMode, agentPortOperationalStatus } STATUS current DESCRIPTION "This collection of objects provide switching configuration information." ::= { bsnSwitchingGroups 2} bsnSwitchingAgentSystemGroup OBJECT-GROUP OBJECTS { agentSaveConfig, agentClearConfig, agentClearLags, agentClearLoginSessions, agentClearPortStats, agentClearSwitchStats, agentClearTrapLog, agentResetSystem } STATUS current DESCRIPTION "This collection of objects provide switching system information and config." ::= { bsnSwitchingGroups 3 } bsnSwitchingAgentStatsGroup OBJECT-GROUP OBJECTS { portStatsIndex, portStatsPktsTx64Octets, portStatsPktsTx65to127Octets, portStatsPktsTx128to255Octets, portStatsPktsTx256to511Octets, portStatsPktsTx512to1023Octets, portStatsPktsTx1024to1518Octets, portStatsPktsRx1519to1530Octets, portStatsPktsTx1519to1530Octets, portStatsPktsTxOversizeOctets } STATUS current DESCRIPTION "This collection of objects provide switching statistics." ::= { bsnSwitchingGroups 4 } bsnSwitchingObsGroup OBJECT-GROUP OBJECTS { agentLagConfigCreate, agentLagSummaryName, agentLagSummaryLagIndex, agentLagSummaryLinkTrap, agentLagSummaryAdminMode, agentLagSummaryStpMode, agentLagSummaryAddPort, agentLagSummaryDeletePort, agentLagSummaryPortsBitMask, agentLagSummaryStatus, agentLagDetailedLagIndex, agentLagDetailedIfIndex, agentLagDetailedPortSpeed, agentLagConfigMode, agentServicePortIPAddress, agentServicePortSubnetMask, agentServicePortBurnedInMacAddress, agentServicePortConfigProtocol, agentSnmpBroadcastStormTrapFlag, agentDot3adAggPort, agentDot3adAggPortLACPMode, agentNetworkGvrpStatus, agentPortGvrpStatus, agentPortGarpJoinTime, agentPortGarpLeaveTime, agentPortGarpLeaveAllTime, agentLagSummaryFlushTimer, agentServicePortDefaultGateway } STATUS obsolete DESCRIPTION "This collection of objects are obsoleted in bsnSwitching module." ::= { bsnSwitchingGroups 5 } bsnSwitchingTrap NOTIFICATION-GROUP NOTIFICATIONS { multipleUsersTrap, broadcastStormStartTrap, broadcastStormEndTrap, linkFailureTrap, vlanRequestFailureTrap, vlanDeleteLastTrap, vlanDefaultCfgFailureTrap, vlanRestoreFailureTrap, fanFailureTrap, stpInstanceNewRootTrap, stpInstanceTopologyChangeTrap, powerSupplyStatusChangeTrap } STATUS current DESCRIPTION "This collection of objects provides switching related notification." ::= { bsnSwitchingGroups 6 } --******************************************************************** --* End of units of conformance --******************************************************************** END