-------------------------------------------------------------------- -- Placeholder for ILMI support -- -- March, 1995 Kartik Chandrasekhar -- -- Copyright (c) 1996-1997 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** -- -- This mib was extracted from the ATM Forum ATM UNI 4.0 Specification. ATM-FORUM-MIB DEFINITIONS ::= BEGIN IMPORTS TruthValue, ClnpAddress, AtmServiceCategory, atmfPhysicalGroup, atmfAtmLayerGroup, atmfAtmStatsGroup, atmfVpcGroup, atmfVccGroup, atmfVpcAbrGroup, atmfVccAbrGroup FROM ATM-FORUM-TC-MIB Counter, IpAddress FROM RFC1155-SMI DisplayString FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212; -- Textual Conventions -- All representations of ATM addresses in this MIB Module use -- the data type: AtmAddress ::= OCTET STRING (SIZE (0 .. 32)) -- Note this data type is used only by the deprecated object -- atmfPortAddress. Another definition (a refined one) is -- specified in the Textual Conventions MIB. -- The Physical Port Group -- -- This group is mandatory for all ATM Interface devices. -- -- The Physical Port Table atmfPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of physical layer status and parameter information for the ATM Interface's physical interface." ::= { atmfPhysicalGroup 1 } atmfPortEntry OBJECT-TYPE SYNTAX AtmfPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing information about the physical layer of an ATM Interface." INDEX { atmfPortIndex } ::= { atmfPortTable 1 } AtmfPortEntry ::= SEQUENCE { atmfPortIndex INTEGER, atmfPortAddress AtmAddress, atmfPortTransmissionType OBJECT IDENTIFIER, atmfPortMediaType OBJECT IDENTIFIER, atmfPortOperStatus INTEGER, atmfPortSpecific OBJECT IDENTIFIER, atmfPortMyIfName DisplayString, atmfPortMyIfIdentifier INTEGER } atmfPortIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received." ::= { atmfPortEntry 1 } atmfPortAddress OBJECT-TYPE SYNTAX AtmAddress ACCESS read-only STATUS obsolete DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 2.0 of the UNI specification. The Address Group, defined in theAddress Registration MIB should be used instead." ::= { atmfPortEntry 2 } atmfPortTransmissionType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead." ::= { atmfPortEntry 3 } atmfPortMediaType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead." ::= { atmfPortEntry 4 } atmfPortOperStatus OBJECT-TYPE SYNTAX INTEGER { other(1), inService(2), outOfService(3), loopBack(4) } ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead." ::= { atmfPortEntry 5 } atmfPortSpecific OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead." ::= { atmfPortEntry 6 } atmfPortMyIfName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "A textual name of this interface. If this system is manageable through SNMP, and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. This interface must be uniquely named on this system to distinguish parallel links with a neighboring system. If this interface does not have a textual name, the value of this object is a zero length string." ::= { atmfPortEntry 7 } atmfPortMyIfIdentifier OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each ATM interface. The scheme used to number the ATM interfaces on an ATM device is implementation specific. One way to generate this value is to use the ifIndex that an SNMP manager would use to identify the port. This interface must be uniquely numbered on this system to distinguish parallel links with a neighboring system." ::= { atmfPortEntry 8 } -- Note: The typical IME will support only one of the following two objects atmfMyIpNmAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "An IP Address to which a Network Management Station can send Network Management protocol messages, e.g. SNMP messages to UDP port 161, in order to access network management information concerning the operation of the ATM device local to this IME. If this object is supported, but the Network Management Agent has not been configured with an IP Address, the IME should return 0.0.0.0." ::= { atmfPhysicalGroup 2 } atmfMyOsiNmNsapAddress OBJECT-TYPE SYNTAX ClnpAddress ACCESS read-only STATUS mandatory DESCRIPTION "An NSAP Address to which a Network Management Station can send Network Management protocol messages in order to access network management information concerning the operation of the ATM device local to this IME. If this object is supported, but the Network Management Agent has not been configured with an NSAP Address, the IME should return 0.0.0.0" ::= { atmfPhysicalGroup 3 } atmfMySystemIdentifier OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "A 48 bit identifier, taken from the IEEE universally administered MAC address space, which uniquely identifies the ATM device local to this IME." ::= { atmfPhysicalGroup 4 } -- The ATM Layer Group -- This group is mandatory for all ATM Interfaces. -- -- ATM-layer specific information for the ATM Interface. atmfAtmLayerTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAtmLayerEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of ATM layer status and parameter information for the ATM Interface." ::= { atmfAtmLayerGroup 1 } atmfAtmLayerEntry OBJECT-TYPE SYNTAX AtmfAtmLayerEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing information about the ATM layer of an ATM Interface." INDEX { atmfAtmLayerIndex } ::= { atmfAtmLayerTable 1 } AtmfAtmLayerEntry ::= SEQUENCE { atmfAtmLayerIndex INTEGER, atmfAtmLayerMaxVPCs INTEGER, atmfAtmLayerMaxVCCs INTEGER, atmfAtmLayerConfiguredVPCs INTEGER, atmfAtmLayerConfiguredVCCs INTEGER, atmfAtmLayerMaxVpiBits INTEGER, atmfAtmLayerMaxVciBits INTEGER, atmfAtmLayerUniType INTEGER, atmfAtmLayerUniVersion INTEGER, atmfAtmLayerDeviceType INTEGER, atmfAtmLayerIlmiVersion INTEGER, atmfAtmLayerNniSigVersion INTEGER, atmfAtmLayerMaxSvpcVpi INTEGER, atmfAtmLayerMaxSvccVpi INTEGER, atmfAtmLayerMinSvccVci INTEGER } atmfAtmLayerIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received." ::= { atmfAtmLayerEntry 1 } atmfAtmLayerMaxVPCs OBJECT-TYPE SYNTAX INTEGER (0..4096) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of switched and permanent VPCs supported on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections), the maximum number of VPCs PNNI may communicate over is set to zero." ::= { atmfAtmLayerEntry 2 } atmfAtmLayerMaxVCCs OBJECT-TYPE SYNTAX INTEGER (0..268435456) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of switched and permanent VCCs supported on this ATM Interface." ::= { atmfAtmLayerEntry 3 } atmfAtmLayerConfiguredVPCs OBJECT-TYPE SYNTAX INTEGER (0..4096) ACCESS read-only STATUS mandatory DESCRIPTION "The number of permanent VPCs configured for use on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections used by PNNI), the maximum number of VPCs is set to zero." ::= { atmfAtmLayerEntry 4 } atmfAtmLayerConfiguredVCCs OBJECT-TYPE SYNTAX INTEGER (0.. 268435456) ACCESS read-only STATUS mandatory DESCRIPTION "The number of permanent VCCs configured for use on this ATM Interface." ::= { atmfAtmLayerEntry 5 } atmfAtmLayerMaxVpiBits OBJECT-TYPE SYNTAX INTEGER (0..12) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of active VPI bits on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections used by PNNI), this value has no meaning and is set to zero." ::= { atmfAtmLayerEntry 6 } atmfAtmLayerMaxVciBits OBJECT-TYPE SYNTAX INTEGER (0..16) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of active VCI bits on this ATM Interface." ::= { atmfAtmLayerEntry 7 } atmfAtmLayerUniType OBJECT-TYPE SYNTAX INTEGER { public(1), private(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of the ATM device, either public or private." ::= { atmfAtmLayerEntry 8 } atmfAtmLayerUniVersion OBJECT-TYPE SYNTAX INTEGER { version2point0(1), version3point0(2), version3point1(3), version4point0(4), unsupported(5) } ACCESS read-only STATUS mandatory DESCRIPTION "An indication of the latest version of the ATM Forum UNI Signalling Specification that is supported on this ATM Interface. If this value is not present, a version of the UNI earlier than 3.1 is supported. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed." ::= { atmfAtmLayerEntry 9 } atmfAtmLayerDeviceType OBJECT-TYPE SYNTAX INTEGER { user(1), node(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This object determines the type of the ATM device. This object is used in automatic ATM Interface-Type determination procedure such that a correct operational ATM Interface-type can be determined. An ATM End System shall take the value of user(1), and an ATM network node shall take the value of node(2)." ::= { atmfAtmLayerEntry 10 } atmfAtmLayerIlmiVersion OBJECT-TYPE SYNTAX INTEGER { unsupported(1), version4point0(2) } ACCESS read-only STATUS mandatory DESCRIPTION "An indication of the latest version of the ATM Forum ILMI Specification that is supported on this ATM Interface. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. If this object is not present, a version of the ILMI earlier than 4.0 is supported." ::= { atmfAtmLayerEntry 11 } atmfAtmLayerNniSigVersion OBJECT-TYPE SYNTAX INTEGER { unsupported(1), iisp(2), pnniVersion1point0(3) } ACCESS read-only STATUS mandatory DESCRIPTION "An indication of the latest version of the ATM Forum PNNI Signalling Specification that is supported on this ATM Interface. Note that the PNNI routing version is not determined through ILMI. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed." ::= { atmfAtmLayerEntry 12 } atmfAtmLayerMaxSvpcVpi OBJECT-TYPE SYNTAX INTEGER (0..4096) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum VPI that the signalling stack on the ATM interface is configured to support for allocation to switched virtual path connections." ::= { atmfAtmLayerEntry 13 } atmfAtmLayerMaxSvccVpi OBJECT-TYPE SYNTAX INTEGER (0..4096) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum VPI that the signalling stack on the ATM interface is configured to support for allocation to switched virtual channel connections." ::= { atmfAtmLayerEntry 14 } atmfAtmLayerMinSvccVci OBJECT-TYPE SYNTAX INTEGER (0..65536) ACCESS read-only STATUS mandatory DESCRIPTION "This is the minimum VCI value that the signalling stack is configured to support for allocation to switched virtual channel connections. The same value applies to all SVCC VPI values for which the signalling stack is configured." ::= { atmfAtmLayerEntry 15 } -- The ATM Statistics Group -- This group is deprecated and should not be implemented except as -- required for backward compatibility with version 3.1 of the UNI -- specification. atmfAtmStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAtmStatsEntry ACCESS not-accessible STATUS deprecated DESCRIPTION "This group is deprecated and should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." ::= { atmfAtmStatsGroup 1 } atmfAtmStatsEntry OBJECT-TYPE SYNTAX AtmfAtmStatsEntry ACCESS not-accessible STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." INDEX { atmfAtmStatsIndex } ::= { atmfAtmStatsTable 1 } AtmfAtmStatsEntry ::= SEQUENCE { atmfAtmStatsIndex INTEGER, atmfAtmStatsReceivedCells Counter, atmfAtmStatsDroppedReceivedCells Counter, atmfAtmStatsTransmittedCells Counter } atmfAtmStatsIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." ::= { atmfAtmStatsEntry 1 } atmfAtmStatsReceivedCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." ::= { atmfAtmStatsEntry 2 } atmfAtmStatsDroppedReceivedCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." ::= { atmfAtmStatsEntry 3 } atmfAtmStatsTransmittedCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." ::= { atmfAtmStatsEntry 4 } -- The Virtual Path Group -- This group is mandatory for all ATM Interfaces. -- -- Information concerning Virtual Path Connections atmfVpcTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfVpcEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of status and parameter information on the virtual path connections which cross this ATM Interface. There is one entry in this table for each permanent virtual path connection." ::= { atmfVpcGroup 1 } atmfVpcEntry OBJECT-TYPE SYNTAX AtmfVpcEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing information about a particular virtual path connection." INDEX { atmfVpcPortIndex, atmfVpcVpi } ::= { atmfVpcTable 1 } AtmfVpcEntry ::= SEQUENCE { atmfVpcPortIndex INTEGER, atmfVpcVpi INTEGER, atmfVpcOperStatus INTEGER, atmfVpcTransmitTrafficDescriptorType OBJECT IDENTIFIER, atmfVpcTransmitTrafficDescriptorParam1 INTEGER, atmfVpcTransmitTrafficDescriptorParam2 INTEGER, atmfVpcTransmitTrafficDescriptorParam3 INTEGER, atmfVpcTransmitTrafficDescriptorParam4 INTEGER, atmfVpcTransmitTrafficDescriptorParam5 INTEGER, atmfVpcReceiveTrafficDescriptorType OBJECT IDENTIFIER, atmfVpcReceiveTrafficDescriptorParam1 INTEGER, atmfVpcReceiveTrafficDescriptorParam2 INTEGER, atmfVpcReceiveTrafficDescriptorParam3 INTEGER, atmfVpcReceiveTrafficDescriptorParam4 INTEGER, atmfVpcReceiveTrafficDescriptorParam5 INTEGER, atmfVpcQoSCategory INTEGER, atmfVpcTransmitQoSClass INTEGER, atmfVpcReceiveQoSClass INTEGER, atmfVpcBestEffortIndicator TruthValue, atmfVpcServiceCategory AtmServiceCategory } atmfVpcPortIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received." ::= { atmfVpcEntry 1 } atmfVpcVpi OBJECT-TYPE SYNTAX INTEGER (0..4095) ACCESS read-only STATUS mandatory DESCRIPTION "The VPI value of this Virtual Path Connection at the local ATM Interface." ::= { atmfVpcEntry 2 } atmfVpcOperStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), end2endUp(2), end2endDown(3), localUpEnd2endUnknown(4), localDown(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The present actual operational status of the VPC. A value of end2endUp(2) or end2endDown(3) would be used if the end-to-end status is known. If only local status information is available, a value of localUpEnd2endUnknown(4) or localDown(5) would be used." ::= { atmfVpcEntry 3 } atmfVpcTransmitTrafficDescriptorType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "The type of traffic management, applicable to the transmit direction of this VPC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVpcTransmitTrafficDescriptorParam1, atmfVpcTransmitTrafficDescriptorParam2, atmfVpcTransmitTrafficDescriptorParam3, atmfVpcTransmitTrafficDescriptorParam4, and atmfVpcTransmitTrafficDescriptorParam5." ::= { atmfVpcEntry 4 } atmfVpcTransmitTrafficDescriptorParam1 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The first parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType." ::= { atmfVpcEntry 5 } atmfVpcTransmitTrafficDescriptorParam2 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The second parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType." ::= { atmfVpcEntry 6 } atmfVpcTransmitTrafficDescriptorParam3 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The third parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType." ::= { atmfVpcEntry 7 } atmfVpcTransmitTrafficDescriptorParam4 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The fourth parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType." ::= { atmfVpcEntry 8 } atmfVpcTransmitTrafficDescriptorParam5 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The fifth parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType." ::= { atmfVpcEntry 9 } atmfVpcReceiveTrafficDescriptorType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "The type of traffic management, applicable to the traffic in the receive direction of this VPC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVpcReceiveTrafficDescriptorParam1, atmfVpcReceiveTrafficDescriptorParam2, atmfVpcReceiveTrafficDescriptorParam3, atmfVpcReceiveTrafficDescriptorParam4, and atmfVpcReceiveTrafficDescriptorParam5." ::= { atmfVpcEntry 10 } atmfVpcReceiveTrafficDescriptorParam1 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The first parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType." ::= { atmfVpcEntry 11 } atmfVpcReceiveTrafficDescriptorParam2 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The second parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType." ::= { atmfVpcEntry 12 } atmfVpcReceiveTrafficDescriptorParam3 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The third parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType." ::= { atmfVpcEntry 13 } atmfVpcReceiveTrafficDescriptorParam4 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The fourth parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType." ::= { atmfVpcEntry 14 } atmfVpcReceiveTrafficDescriptorParam5 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The fifth parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType." ::= { atmfVpcEntry 15 } atmfVpcQoSCategory OBJECT-TYPE SYNTAX INTEGER { other(1), deterministic (2), statistical (3), unspecified (4) } ACCESS read-only STATUS obsolete DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 2.0 of the UNI specification." ::= { atmfVpcEntry 16 } atmfVpcTransmitQoSClass OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." ::= { atmfVpcEntry 17 } atmfVpcReceiveQoSClass OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." ::= { atmfVpcEntry 18 } atmfVpcBestEffortIndicator OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "The object is examined when atmfVpcTransmitTrafficDescriptorType or atmfVpcReceiveTrafficDescriptorType for the associated connection is equal to atmfNoClpNoScr. If this object is set to false(2), the network is requested to apply the CBR.1 conformance definition. If this object is set to true(1), the network is requested to apply the UBR.1 conformance definition." ::= { atmfVpcEntry 19 } atmfVpcServiceCategory OBJECT-TYPE SYNTAX AtmServiceCategory ACCESS read-only STATUS mandatory DESCRIPTION "The service category of this virtual path connection." ::= { atmfVpcEntry 20 } -- The Virtual Path ABR Group -- This group contains per-VPC information, support for which is optional. -- -- Attributes of ABR Virtual Path connections atmfVpcAbrTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfVpcAbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of operational parameters related to the ABR virtual path connections which cross this ATM Interface. There is one entry in this table for each ABR virtual path connection. Each virtual path connection represented in this table must also be represented by an entry in the atmfVpcTable." ::= { atmfVpcAbrGroup 1 } atmfVpcAbrEntry OBJECT-TYPE SYNTAX AtmfVpcAbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing information about a particular ABR virtual path connection." INDEX { atmfVpcAbrPortIndex, atmfVpcAbrVpi } ::= { atmfVpcAbrTable 1 } AtmfVpcAbrEntry ::= SEQUENCE { atmfVpcAbrPortIndex INTEGER, atmfVpcAbrVpi INTEGER, atmfVpcAbrTransmitIcr INTEGER, atmfVpcAbrTransmitNrm INTEGER, atmfVpcAbrTransmitTrm INTEGER, atmfVpcAbrTransmitCdf INTEGER, atmfVpcAbrTransmitRif INTEGER, atmfVpcAbrTransmitRdf INTEGER, atmfVpcAbrTransmitAdtf INTEGER, atmfVpcAbrTransmitCrm INTEGER } atmfVpcAbrPortIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received." ::= { atmfVpcAbrEntry 1 } atmfVpcAbrVpi OBJECT-TYPE SYNTAX INTEGER (0..4095) ACCESS read-only STATUS mandatory DESCRIPTION "The VPI value of this ABR Virtual Path Connection at the local ATM Interface." ::= { atmfVpcAbrEntry 2 } atmfVpcAbrTransmitIcr OBJECT-TYPE SYNTAX INTEGER (0..16777215) ACCESS read-only STATUS mandatory DESCRIPTION "Initial Cell Rate: This is the rate at which the source starts, both initially and after an idle period. The unit is cells per second. The value must not be larger than PCR, and is usually lower." ::= { atmfVpcAbrEntry 3 } atmfVpcAbrTransmitNrm OBJECT-TYPE SYNTAX INTEGER { nrm2(1), nrm4(2), nrm8(3), nrm16(4), nrm32(5), nrm64(6), nrm128(7), nrm256(8) } ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of data cells a source may send for each forward RM-cell. The default value is nrm32(5)." ::= { atmfVpcAbrEntry 4 } atmfVpcAbrTransmitTrm OBJECT-TYPE SYNTAX INTEGER { trm0point78125(1), trm1point5625(2), trm3point125(3), trm6point25(4), trm12point5(5), trm25(6), trm50(7), trm100(8) } ACCESS read-only STATUS mandatory DESCRIPTION "Upper bound on the time between forward RM-cells for an active source (in milliseconds). The default value is trm100(8)." ::= { atmfVpcAbrEntry 5 } atmfVpcAbrTransmitCdf OBJECT-TYPE SYNTAX INTEGER { cdf0(1), cdfOneOver64(2), cdfOneOver32(3), cdfOneOver16(4), cdfOneOver8(5), cdfOneOver4(6), cdfOneOver2(7), cdfOne(8) } ACCESS read-only STATUS mandatory DESCRIPTION "Cutoff Decrease Factor: This field controls the rate decrease associated with lost or delayed backward RM cells. Larger values result in faster rate decrease. The default value is cdfOneOver16(4)." ::= { atmfVpcAbrEntry 6 } atmfVpcAbrTransmitRif OBJECT-TYPE SYNTAX INTEGER { rifOneOver32768(1), rifOneOver16384(2), rifOneOver8192(3), rifOneOver4096(4), rifOneOver2048(5), rifOneOver1024(6), rifOneOver512(7), rifOneOver256(8), rifOneOver128(9), rifOneOver64(10), rifOneOver32(11), rifOneOver16(12), rifOneOver8(13), rifOneOver4(14), rifOneOver2(15), rifOne(16) } ACCESS read-only STATUS mandatory DESCRIPTION "Rate Increment Factor: Controls the rate at which the rate increases, when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12)." ::= { atmfVpcAbrEntry 7 } atmfVpcAbrTransmitRdf OBJECT-TYPE SYNTAX INTEGER { rdfOneOver32768(1), rdfOneOver16384(2), rdfOneOver8192(3), rdfOneOver4096(4), rdfOneOver2048(5), rdfOneOver1024(6), rdfOneOver512(7), rdfOneOver256(8), rdfOneOver128(9), rdfOneOver64(10), rdfOneOver32(11), rdfOneOver16(12), rdfOneOver8(13), rdfOneOver4(14), rdfOneOver2(15), rdfOne(16) } ACCESS read-only STATUS mandatory DESCRIPTION "Rate Decrease Factor: Controls the rate decrease which occurs when backward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12)." ::= { atmfVpcAbrEntry 8 } atmfVpcAbrTransmitAdtf OBJECT-TYPE SYNTAX INTEGER (1..1023) ACCESS read-only STATUS mandatory DESCRIPTION "ACR Decrease Time Factor: Time permitted between sending RM-cells, before the allowed rate (ACR) is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 milliseconds. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds)." ::= { atmfVpcAbrEntry 9 } atmfVpcAbrTransmitCrm OBJECT-TYPE SYNTAX INTEGER (0..8388608) ACCESS read-only STATUS mandatory DESCRIPTION "RM Cells Before Cutoff: Limits the number of forward RM-cells which may be sent in the absence of received backward RM-cells." ::= { atmfVpcAbrEntry 10 } -- The Virtual Channel Group -- This group is mandatory for all ATM Interfaces. -- -- Information concerning Virtual Channel Connections atmfVccTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfVccEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of status and parameter information on the virtual channel connections which are visible at this ATM Interface. There is one entry in this table for each permanent virtual channel connection, including reserved VCCs that are supported; e.g., signalling, OAM flows, and ILMI, but not unassigned cells." ::= { atmfVccGroup 1 } atmfVccEntry OBJECT-TYPE SYNTAX AtmfVccEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing information about a particular virtual channel connection." INDEX { atmfVccPortIndex, atmfVccVpi, atmfVccVci } ::= { atmfVccTable 1 } AtmfVccEntry ::= SEQUENCE { atmfVccPortIndex INTEGER, atmfVccVpi INTEGER, atmfVccVci INTEGER, atmfVccOperStatus INTEGER, atmfVccTransmitTrafficDescriptorType OBJECT IDENTIFIER, atmfVccTransmitTrafficDescriptorParam1 INTEGER, atmfVccTransmitTrafficDescriptorParam2 INTEGER, atmfVccTransmitTrafficDescriptorParam3 INTEGER, atmfVccTransmitTrafficDescriptorParam4 INTEGER, atmfVccTransmitTrafficDescriptorParam5 INTEGER, atmfVccReceiveTrafficDescriptorType OBJECT IDENTIFIER, atmfVccReceiveTrafficDescriptorParam1 INTEGER, atmfVccReceiveTrafficDescriptorParam2 INTEGER, atmfVccReceiveTrafficDescriptorParam3 INTEGER, atmfVccReceiveTrafficDescriptorParam4 INTEGER, atmfVccReceiveTrafficDescriptorParam5 INTEGER, atmfVccQoSCategory INTEGER, atmfVccTransmitQoSClass INTEGER, atmfVccReceiveQoSClass INTEGER, atmfVccBestEffortIndicator TruthValue, atmfVccTransmitFrameDiscard TruthValue, atmfVccReceiveFrameDiscard TruthValue, atmfVccServiceCategory AtmServiceCategory } atmfVccPortIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received." ::= { atmfVccEntry 1 } atmfVccVpi OBJECT-TYPE SYNTAX INTEGER (0..4095) ACCESS read-only STATUS mandatory DESCRIPTION "The VPI value of this Virtual Channel Connection at the local ATM Interface. For virtual interfaces (i.e. Virtual Path Connections), this value has no meaning and is set to zero " ::= { atmfVccEntry 2 } atmfVccVci OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The VCI value of this Virtual Channel Connection at the local ATM Interface." ::= { atmfVccEntry 3 } atmfVccOperStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), end2endUp(2), end2endDown(3), localUpEnd2endUnknown(4), localDown(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The present actual operational status of the VCC. A value of end2endUp(2) or end2endUp(3) is used if the end to end status is known. If only local status is known a value of localUpEnd2endUnknown(4) or localDown(5) is used." ::= { atmfVccEntry 4 } atmfVccTransmitTrafficDescriptorType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "The type of traffic management, applicable to the transmit direction of this VCC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVccTransmitTrafficDescriptorParam1, atmfVccTransmitTrafficDescriptorParam2, atmfVccTransmitTrafficDescriptorParam3, atmfVccTransmitTrafficDescriptorParam4, and atmfVccTransmitTrafficDescriptorParam5." ::= { atmfVccEntry 5 } atmfVccTransmitTrafficDescriptorParam1 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The first parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType." ::= { atmfVccEntry 6 } atmfVccTransmitTrafficDescriptorParam2 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The second parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType." ::= { atmfVccEntry 7 } atmfVccTransmitTrafficDescriptorParam3 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The third parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType." ::= { atmfVccEntry 8 } atmfVccTransmitTrafficDescriptorParam4 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The fourth parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType." ::= { atmfVccEntry 9 } atmfVccTransmitTrafficDescriptorParam5 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The fifth parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType." ::= { atmfVccEntry 10 } atmfVccReceiveTrafficDescriptorType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "The type of traffic management, applicable to the traffic in the receive direction of this VCC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVccReceiveTrafficDescriptorParam1, atmfVccReceiveTrafficDescriptorParam2, atmfVccReceiveTrafficDescriptorParam3, atmfVccReceiveTrafficDescriptorParam4, and atmfVccReceiveTrafficDescriptorParam5." ::= { atmfVccEntry 11 } atmfVccReceiveTrafficDescriptorParam1 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The first parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType." ::= { atmfVccEntry 12 } atmfVccReceiveTrafficDescriptorParam2 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The second parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType." ::= { atmfVccEntry 13 } atmfVccReceiveTrafficDescriptorParam3 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The third parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType." ::= { atmfVccEntry 14 } atmfVccReceiveTrafficDescriptorParam4 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The fourth parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType." ::= { atmfVccEntry 15 } atmfVccReceiveTrafficDescriptorParam5 OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The fifth parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType." ::= { atmfVccEntry 16 } atmfVccQoSCategory OBJECT-TYPE SYNTAX INTEGER { other(1), deterministic(2), statistical(3), unspecified(4) } ACCESS read-only STATUS obsolete DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 2.0 of the UNI specification." ::= { atmfVccEntry 17 } atmfVccTransmitQoSClass OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." ::= { atmfVccEntry 18 } atmfVccReceiveQoSClass OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS deprecated DESCRIPTION "This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification." ::= { atmfVccEntry 19 } atmfVccBestEffortIndicator OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "The object is examined when atmfVccTransmitTrafficDescriptorType or atmfVccReceiveTrafficDescriptorType for the associated connection is equal to atmfNoClpNoScr. If this object is set to false(2), the network is requested to apply the CBR.1 conformance definition. If this object is set to true(1), the network is requested to apply the UBR.1 conformance definition." ::= { atmfVccEntry 20 } atmfVccTransmitFrameDiscard OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "If set to true(1), this object indicates that the network is requested to treat data for this connection (in the transmit direction) as frames (e.g. AAL5 CPCS_PDU's) rather than as individual cells. While the precise implementation is network-specific, this treatment may for example involve discarding entire frames during congestion, rather than a few cells from many frames. The default value is false(2)." ::= { atmfVccEntry 21 } atmfVccReceiveFrameDiscard OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "If set to true(1), this object indicates that the network is requested to treat data for this connection (in the receive direction) as frames (e.g. AAL5 CPCS_PDU's) rather than as individual cells. While the precise implementation is network-specific, this treatment may for example involve discarding entire frames during congestion, rather than a few cells from many frames. The default value is false(2)." ::= { atmfVccEntry 22 } atmfVccServiceCategory OBJECT-TYPE SYNTAX AtmServiceCategory ACCESS read-only STATUS mandatory DESCRIPTION "The service category of this virtual channel connection." ::= { atmfVccEntry 23 } -- The Virtual Channel ABR Group -- This group contains per-VCC information, support for which is optional. -- -- Attributes of ABR Virtual Channel connections atmfVccAbrTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfVccAbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of operational parameters related to the ABR virtual channel connections which cross this ATM Interface. There is one entry in this table for each ABR virtual channel connection. Each virtual channel connection represented in this table must also be represented by an entry in the atmfVccTable." ::= { atmfVccAbrGroup 1 } atmfVccAbrEntry OBJECT-TYPE SYNTAX AtmfVccAbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table, containing information about a particular ABR virtual channel connection." INDEX { atmfVccAbrPortIndex, atmfVccAbrVpi, atmfVccAbrVci } ::= { atmfVccAbrTable 1 } AtmfVccAbrEntry ::= SEQUENCE { atmfVccAbrPortIndex INTEGER, atmfVccAbrVpi INTEGER, atmfVccAbrVci INTEGER, atmfVccAbrTransmitIcr INTEGER, atmfVccAbrTransmitNrm INTEGER, atmfVccAbrTransmitTrm INTEGER, atmfVccAbrTransmitCdf INTEGER, atmfVccAbrTransmitRif INTEGER, atmfVccAbrTransmitRdf INTEGER, atmfVccAbrTransmitAdtf INTEGER, atmfVccAbrTransmitCrm INTEGER } atmfVccAbrPortIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received." ::= { atmfVccAbrEntry 1 } atmfVccAbrVpi OBJECT-TYPE SYNTAX INTEGER (0..4095) ACCESS read-only STATUS mandatory DESCRIPTION "The VPI value of this ABR Virtual Channel Connection at the local ATM Interface. For virtual interfaces (i.e. Virtual Path Connections), this value has no meaning and is set to zero " ::= { atmfVccAbrEntry 2 } atmfVccAbrVci OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The VCI value of this ABR Virtual Channel Connection at the local ATM Interface." ::= { atmfVccAbrEntry 3 } atmfVccAbrTransmitIcr OBJECT-TYPE SYNTAX INTEGER (0..16777215) ACCESS read-only STATUS mandatory DESCRIPTION "Initial Cell Rate: This is the rate at which the source starts, both initially and after an idle period. The unit is cells per second. The value must not be larger than PCR, and is usually lower." ::= { atmfVccAbrEntry 4 } atmfVccAbrTransmitNrm OBJECT-TYPE SYNTAX INTEGER { nrm2(1), nrm4(2), nrm8(3), nrm16(4), nrm32(5), nrm64(6), nrm128(7), nrm256(8) } ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of data cells a source may send for each forward RM-cell. The default value is nrm32(5)." ::= { atmfVccAbrEntry 5 } atmfVccAbrTransmitTrm OBJECT-TYPE SYNTAX INTEGER { trm0point78125(1), trm1point5625(2), trm3point125(3), trm6point25(4), trm12point5(5), trm25(6), trm50(7), trm100(8) } ACCESS read-only STATUS mandatory DESCRIPTION "Upper bound on the time between forward RM-cells for an active source (in milliseconds). The default value is trm100(8)." ::= { atmfVccAbrEntry 6 } atmfVccAbrTransmitCdf OBJECT-TYPE SYNTAX INTEGER { cdf0(1), cdfOneOver64(2), cdfOneOver32(3), cdfOneOver16(4), cdfOneOver8(5), cdfOneOver4(6), cdfOneOver2(7), cdfOne(8) } ACCESS read-only STATUS mandatory DESCRIPTION "Cutoff Decrease Factor: This field controls the rate decrease associated with lost or delayed backward RM cells. Larger values result in faster rate decrease. The default value is cdfOneOver16(4)." ::= { atmfVccAbrEntry 7 } atmfVccAbrTransmitRif OBJECT-TYPE SYNTAX INTEGER { rifOneOver32768(1), rifOneOver16384(2), rifOneOver8192(3), rifOneOver4096(4), rifOneOver2048(5), rifOneOver1024(6), rifOneOver512(7), rifOneOver256(8), rifOneOver128(9), rifOneOver64(10), rifOneOver32(11), rifOneOver16(12), rifOneOver8(13), rifOneOver4(14), rifOneOver2(15), rifOne(16) } ACCESS read-only STATUS mandatory DESCRIPTION "Rate Increment Factor: Controls the rate at which the rate increases, when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12)." ::= { atmfVccAbrEntry 8 } atmfVccAbrTransmitRdf OBJECT-TYPE SYNTAX INTEGER { rdfOneOver32768(1), rdfOneOver16384(2), rdfOneOver8192(3), rdfOneOver4096(4), rdfOneOver2048(5), rdfOneOver1024(6), rdfOneOver512(7), rdfOneOver256(8), rdfOneOver128(9), rdfOneOver64(10), rdfOneOver32(11), rdfOneOver16(12), rdfOneOver8(13), rdfOneOver4(14), rdfOneOver2(15), rdfOne(16) } ACCESS read-only STATUS mandatory DESCRIPTION "Rate Decrease Factor: Controls the rate decrease which occurs when backward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12)." ::= { atmfVccAbrEntry 9 } atmfVccAbrTransmitAdtf OBJECT-TYPE SYNTAX INTEGER (1..1023) ACCESS read-only STATUS mandatory DESCRIPTION "ACR Decrease Time Factor: Time permitted between sending RM-cells, before the allowed rate (ACR) is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 milliseconds. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds)." ::= { atmfVccAbrEntry 10 } atmfVccAbrTransmitCrm OBJECT-TYPE SYNTAX INTEGER (0..8388608) ACCESS read-only STATUS mandatory DESCRIPTION "RM Cells Before Cutoff: Limits the number of forward RM-cells which may be sent in the absence of received backward RM-cells." ::= { atmfVccAbrEntry 11 } -- Traps END