-- ******************************************************************* -- CISCO-LWAPP-WLAN-MIB.my -- This MIB helps to manage the WLANs on the controller -- January 2006, Devesh Pujari, Prasanna Viswakumar -- -- Copyright (c) 2006, 2007, 2009-2016 by Cisco Systems Inc. -- All rights reserved. -- ******************************************************************* CISCO-LWAPP-WLAN-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32, Gauge32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TimeStamp, TruthValue, RowStatus, DisplayString, StorageType, MacAddress FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB ciscoMgmt FROM CISCO-SMI; ciscoLwappWlanMIB MODULE-IDENTITY LAST-UPDATED "201504230000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-wnbu-snmp@cisco.com" DESCRIPTION "This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB helps to manage the WLANs on the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected to. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the controllers. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Access Control List ( ACL ) A list of rules used to restrict the traffic reaching an interface or the CPU or WLAN. Each ACL is an ordered set of rules and actions. If a rule matches then the action for that rule is applied to the packet. 802.1x The IEEE ratified standard for enforcing port based access control. This was originally intended for use on wired LANs and later extended for use in 802.11 WLAN environments. This defines an architecture with three main parts - a supplicant (Ex. an 802.11 wireless client), an authenticator (the AP) and an authentication server(a Radius server). The authenticator passes messages back and forth between the supplicant and the authentication server to enable the supplicant get authenticated to the network. Temporal Key Integrity Protocol ( TKIP ) A security protocol defined to enhance the limitations of WEP. Message Integrity Check and per-packet keying on all WEP-encrypted frames are two significant enhancements provided by TKIP to WEP. Cisco Key Integrity Protocol ( CKIP ) A proprietary implementation similar to TKIP. CKIP implements key permutation for protecting the CKIP key against attacks. Other features of CKIP include expansion of encryption key to 16 bytes of length for key protection and MIC to ensure data integrity. Wired Equivalent Privacy ( WEP ) A security method defined by 802.11. WEP uses a symmetric key stream cipher called RC4 to encrypt the data packets. Wi-Fi Protected Access ( WPA ) Wi-Fi Protected Access (WPA and WPA2) are security systems created in response to several serious weaknesses found in Wired Equivalent Privacy (WEP). WPA implements the majority of the IEEE 802.11i standard, and was intended as an intermediate measure to take the place of WEP while 802.11i was prepared. WPA is designed to work with all wireless network interface cards, but not necessarily with first generation wireless access points. WLAN Layer 2 Security WLAN layer 2 (MAC) security defines the encryption and authentication approaches such as 802.1x, WPA, WPA2, CKIP and WEP. Delivery Traffic Indication Map ( DTIM ) DTIM is measured in beacon intervals and is the time period during which multicast/broadcast packets are sent to clients. This helps client to go in Power Saving mode and helps to save battery power. Network Admission Control (NAC) Cisco NAC uses the network infrastructure to enforce security policy compliance on all devices that seek to access network computing resources. With the Cisco NAC appliance, network administrators can authenticate, authorize, evaluate, and remediate wired, wireless, and remote users and their machines prior to network access. The Cisco NAC appliance identifies whether networked devices such as laptops, IP phones, or game consoles are compliant with network security policies, and repairs any vulnerabilities before it permits access to the network. Out of Band (OOB) Out-of-band deployments require user traffic to traverse through the NAC appliance only within authentication, posture assessment, and remediation. When a user is authenticated and passes all policy checks, the traffic is switched normally through the network and bypasses the NAC server. Band Select The 2.4 GHz band is congested and clients have to contend with numerous performance challenges. These consist of interference from Bluetooth, microwave ovens, cordless phones, etc.; protection mechanisms from 802.11b legacy clients; and co-channel interference from other access points due to 802.11bg?s limit of three non-overlapping channels. Allowing client Wi-Fi radios capable of dual band (2.4 and 5 GHz) operation move to the less congested 5 GHz radios would improve the overall performance of the network. The Band Select algorithm is based on probe response suppression on clients 2.4G radio. The feature is OFF by default and has to be manually switched ON globally for a WLC. It can be optionally over-ridden per-SSID to disallow it. Network Access Identifier ( NAI ) In order to provide roaming services, it is necessary to have a standardized method for identifying users. NAI is actually the user identity submitted by the client during network authentication. KTS (Key Telephone System) Key Telephone System is an alternative to a private branch exchange (PBX)phone system. A KTS is equipped with several buttons that allow a caller to directly select outgoing lines or incoming calls, and use intercom and conference facilities. HALO (Hyperlocation) Hyperlocation is a technique of calculating location using Angle of Arrival(AoA) tracks 802.11 OFDM clients (meaning 802.11a/g/n/ac clients) that are associated(connected) on the network and is able to do so with much higher accuracy than conventional Real Time Location Systems(RTLS) that rely on only RSSI (RF Signal Strength). PakRSSI (Packet Received Signal Strength Indicator) PakRSSI is a measurement of the power present in a received radio signal. POE (Power Over Ethernet) Power over Ethernet or PoE describes any of several standardized or ad-hoc systems which pass electrical power along with data on Ethernet cabling. This allows a single cable to provide both data connection and electrical power to devices such as wireless access points or IP cameras. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol [3] IEEE 802.11 - The original 1 Mbit/s and 2 Mbit/s, 2.4 GHz RF and IR standard." REVISION "201604070000Z" DESCRIPTION "Added new tables ciscoLwappAPGroupsHyperlocationConfig to support Hyperlocation feature and ciscoLwappAPGroupsPortConfig to support AP Group LAN port configurations. Added new groups ciscoLwappWlanConfigGroupSup8, ciscoLwappWlanConfigGroupSup9. Added new compliance ciscoLwappWlanMIBComplianceRev8 which deprecates ciscoLwappWlanMIBComplianceRev7." REVISION "201504230000Z" DESCRIPTION "Added Default value to the cLWlanMulticastInterface object." REVISION "201504170000Z" DESCRIPTION "Added cLWlan11acMuMimoEnabled object to cLWlanConfigEntry. ciscoLwappWlanMIBComplianceRev6 is superceded by ciscoLwappWlanMIBComplianceRev7 Added new group ciscoLwappWlanConfigGroupSup6." REVISION "201411050000Z" DESCRIPTION "Added the cLWlanSelfAnchorEnabled to support the mobility self anchor. cLAPGroupsVlanMappingInterfaceName is superceded by cLAPGroupsVlanMappingInterfaceNameRev1. ciscoLwappAPGroupsVlanConfigGroup is superceded by ciscoLwappAPGroupsVlanConfigGroupSup2. ciscoLwappWlanMIBComplianceRev5 is superceded by ciscoLwappWlanMIBComplianceRev6 Added cLWlanUniversalAdmin object to cLWlanConfigEntry. Added new group ciscoLwappWlanConfigGroupSup5." REVISION "201303300000Z" DESCRIPTION "Added cLWlanFlexibleNetflowTable to support AVC feature. Added new object group CiscoLwappWlanConfigFlexibleNetflowGroup. Added new compliance ciscoLwappWlanMIBComplianceRev5 which deprecates ciscoLwappWlanMIBComplianceRev4." REVISION "201206210000Z" DESCRIPTION "Added the following objects WLAN QoS Config table, AP group Venue Table, ciscoLwappWlanQosConfigGroup ciscoLwappWlanConfigGroupSup4 ciscoLwappWlan11uConfigGroupsup2 ciscoLwappWlanHotSpot2ConfigGroupSup1 ciscoLwappAPGroupsVlanConfigGroupSup1 cLAPGroupsVenueConfigGroup cLAPGroupsMultipleVenueGroup ciscoLwappWlanConfigClientGroupSup2 WLAN IOS objects. - Added the following objects to cLWlan11uTable. cLWlan11uHessid, cLWlan11uNetworkAuthType, cLWlan11uOui, cLWlan11uOuiIsBeacon, cWlan11uOuiRowStatus, cLWlan11uOuiStorageType, cLWlan11uRealmName, cLWlan11uRealmRowStatus, cLWlan11uRealmEapMethod, cLWlan11uRealmEapRowStatus, cLWlan11uRealmEapAuthMethod, cLWlan11uRealmEapAuthParam, cLWlan11uRealmEapAuthRowStatus, cLWlan11uDomainName, cLWlan11uDomainRowStatus, cLWlan11u3gppCountryCode, cLWlan11u3gppNetworkCode, cLWlan11u3gppRowStatus, cLWlan11uIpAddressAvailIpv4, cLWlan11uIpAddressAvailIpv6 - Added the following OBJECT-GROUPs: ciscoLwappWlan11uConfigGroupsup1 ciscoLwappWlanServiceAdvertisementConfigGroup, ciscoLwappWlanHotSpot2ConfigGroup - Added new compliance ciscoLwappWlanMIBComplianceRev4 which deprecates ciscoLwappWlanMIBComplianceRev3." REVISION "201103100000Z" DESCRIPTION "Added the following objects to cLWlanConfigTable. cLWlanReAnchorRoamedVoiceClientsEnable, cLWlanMulticastInterfaceEnable, cLWlanMulticastInterface, cLWlanMulticastDirectEnable, cLWlanNACPostureSupport, cLWlanMaxClientsAccepted, cLWlanScanDeferPriority, cLWlanScanDeferTime, cLWlanLanSubType, cLWlanWebAuthOnMacFilterFailureEnabled, cLWlanStaticIpTunnelingEnabled. - Added new group ciscoLwappWlanConfigGroupSup3. - Added new compliance ciscoLwappWlanMIBComplianceRev3 which deprecates ciscoLwappWlanMIBComplianceRev2." REVISION "201003030000Z" DESCRIPTION "Added the following OBJECT-GROUPs: ciscoLwappWlan11uConfigGroup ciscoLwappAPGroupsVlanConfigGroup ciscoLwappWlanConfigGroupSup2 ciscoLwappWlanConfigClientGroupSup1" REVISION "200704020000Z" DESCRIPTION "Added following object in cLWlanConfigClientTable cLWlanP2PBlocking" REVISION "200702030000Z" DESCRIPTION "Added following objects in cLWlanConfigTable: cLWlanProfileName cLWlanSsid cLWlanDiagChan cLWlanStorageType Added following table: cLWlanConfigClientTable Added the following OBJECT-GROUPs: ciscoLwappWlanConfigGroupSup1 ciscoLwappWlanConfigClientGroup Added ciscoLwappWlanMIBComplianceRev1 MODULE-COMPLIANCE." REVISION "200603210000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 512 } ciscoLwappWlanMIBNotifs OBJECT IDENTIFIER ::= { ciscoLwappWlanMIB 0 } ciscoLwappWlanMIBObjects OBJECT IDENTIFIER ::= { ciscoLwappWlanMIB 1 } ciscoLwappWlanMIBConform OBJECT IDENTIFIER ::= { ciscoLwappWlanMIB 2 } ciscoLwappWlanConfig OBJECT IDENTIFIER ::= { ciscoLwappWlanMIBObjects 1 } ciscoLwappAPGroupsVlanConfig OBJECT IDENTIFIER ::= { ciscoLwappWlanMIBObjects 2 } ciscoLwappWlan11uConfig OBJECT IDENTIFIER ::= { ciscoLwappWlanMIBObjects 3 } ciscoLwappWlanServiceAdvertisementConfig OBJECT IDENTIFIER ::= { ciscoLwappWlanMIBObjects 4 } ciscoLwappWlanHotSpot2Config OBJECT IDENTIFIER ::= { ciscoLwappWlanMIBObjects 5 } ciscoLwappAPGroupsHyperlocationConfig OBJECT IDENTIFIER ::= { ciscoLwappWlanMIBObjects 8 } ciscoLwappAPGroupsPortConfig OBJECT IDENTIFIER ::= { ciscoLwappWlanMIBObjects 9 } -- ******************************************************************** -- WLAN configuration -- ******************************************************************** cLWlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the WLAN configuration sent by the controller to the LWAPP APs for their operation. LWAPP APs exchange configuration messages with the controller and get the required configuration for their 802.11 related operations. As part of these messages, the WLAN configuration is pushed by the controller to the LWAPP APs. This table doesn't have any dependencies on other existing tables. By defining cLWlanIndex, the unique identifier for a WLAN, this table provides a common index structure for use in several other new tables that populate information on security related attributes like authentication, encryption, 802.11 parameters, Quality-of-Service attributes etc., that would relate to a particular WLAN. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlanRowStatus object." ::= { ciscoLwappWlanConfig 1 } cLWlanConfigEntry OBJECT-TYPE SYNTAX CLWlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the WLAN configuration sent by the controller to LWAPP APs for use during their operations. entries can be added/deleted by explicit management actions by NMS or by user console" INDEX { cLWlanIndex } ::= { cLWlanConfigTable 1 } CLWlanConfigEntry ::= SEQUENCE { cLWlanIndex Unsigned32, cLWlanRowStatus RowStatus, cLWlanProfileName SnmpAdminString, cLWlanSsid OCTET STRING, cLWlanDiagChan TruthValue, cLWlanStorageType StorageType, cLWlanIsWired TruthValue, cLWlanIngressInterface OCTET STRING, cLWlanNACSupport TruthValue, cLWlanWepKeyChange TimeStamp, cLWlanChdEnable TruthValue, cLWlan802dot11anDTIM Unsigned32, cLWlan802dot11bgnDTIM Unsigned32, cLWlanLoadBalancingEnable TruthValue, cLWlanBandSelectEnable TruthValue, cLWlanPassiveClientEnable TruthValue, cLWlanReAnchorRoamedVoiceClientsEnable TruthValue, cLWlanMulticastInterfaceEnable TruthValue, cLWlanMulticastInterface SnmpAdminString, cLWlanMulticastDirectEnable TruthValue, cLWlanNACPostureSupport TruthValue, cLWlanMaxClientsAccepted Unsigned32, cLWlanScanDeferPriority BITS, cLWlanScanDeferTime Unsigned32, cLWlanLanSubType INTEGER, cLWlanWebAuthOnMacFilterFailureEnabled TruthValue, cLWlanStaticIpTunnelingEnabled TruthValue, cLWlanKtsCacSupportEnabled TruthValue, cLWlanWifiDirectPolicyStatus INTEGER, cLWlanWebAuthIPv6AclName DisplayString, cLWlanHotSpot2Enabled TruthValue, cLWlanMaxClientsAllowedPerRadio Unsigned32, cLWlanDhcpDeviceProfiling TruthValue, cLWlanMacAuthOverDot1xEnabled TruthValue, cLWlanUserTimeout Unsigned32, cLWlanUserIdleThreshold Unsigned32, cLWlanHttpDeviceProfiling TruthValue, cLWlanHotSpotClearConfig INTEGER, cLWlanRadiusAuthFourthServer DisplayString, cLWlanRadiusAuthFifthServer DisplayString, cLWlanRadiusAuthSixthServer DisplayString, cLWlanRadiusAcctFourthServer DisplayString, cLWlanRadiusAcctFifthServer DisplayString, cLWlanRadiusAcctSixthServer DisplayString, cLWlanSelfAnchorEnabled TruthValue, cLWlanUniversalAdmin TruthValue, cLWlan11acMuMimoEnabled TruthValue } cLWlanIndex OBJECT-TYPE SYNTAX Unsigned32 (1..517) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies one instance of a WLAN on the controller. The value 513-517 indicates wired clients." ::= { cLWlanConfigEntry 1 } cLWlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This is the status column for this row and used to create, modify and delete specific instances of rows in this table. This table supports modification of writable objects when the RowStatus is 'active'. The following objects are mandatory for successful creation of an entry: cLWlanProfileName cLWlanSsid." ::= { cLWlanConfigEntry 2 } cLWlanProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the profile name assigned to this WLAN. The name assigned to a WLAN has to be unique across all the WLANs on the controller. An administrator can assign a meaningful name that could later be used to refer a particular WLAN on the controller. This object cannot be modified when cLWlanRowStatus is 'active'." ::= { cLWlanConfigEntry 3 } cLWlanSsid OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the SSID assigned to this WLAN. The access points will broadcast this SSID on this WLAN. Different WLAN could use the same SSID as long as the layer 2 security is different. This object cannot be modified when cLWlanRowStatus is 'active'." ::= { cLWlanConfigEntry 4 } cLWlanDiagChan OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure this WLAN as a diagnostic WLAN. A value of 'true' indicates that the WLAN can be used for diagnostic purposes. A value of 'false' indicates that the WLAN can not be used for diagnostic purposes." DEFVAL { false } ::= { cLWlanConfigEntry 5 } cLWlanStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This object represnts the storage type for this conceptual row." DEFVAL { nonVolatile } ::= { cLWlanConfigEntry 6 } cLWlanIsWired OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure this WLAN as a wired or wireless WLAN. A value of 'true' indicates that this is a wired WLAN. A value of 'false' indicates that this is a wireless WLAN." ::= { cLWlanConfigEntry 7 } cLWlanIngressInterface OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the ingress interface attached to the wireless lan." ::= { cLWlanConfigEntry 8 } cLWlanNACSupport OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the NAC- Out Of Band(OOB) support for the WLAN. A value of 'true' indicates that the WLAN supports the NAC- Out Of Band(OOB) feature. A value of 'false' indicates that the WLAN does not support the NAC- Out Of Band(OOB) feature." DEFVAL { false } ::= { cLWlanConfigEntry 9 } cLWlanWepKeyChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time when the static WEP key was changed by the user." ::= { cLWlanConfigEntry 10 } cLWlanChdEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether Coverage Hole Detection (CHD) is enabled on the controller. A value of 'true' indicates CHD is on and a value of 'false' indicates CHD is turned off for this WLAN." DEFVAL { true } ::= { cLWlanConfigEntry 11 } cLWlan802dot11anDTIM OBJECT-TYPE SYNTAX Unsigned32 (1..255) UNITS "Beacon Intervals" MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents DTIM configuration per WLAN for each 802.11 network. The DTIM value is measured in Beacon Intervals." DEFVAL { 1 } ::= { cLWlanConfigEntry 12 } cLWlan802dot11bgnDTIM OBJECT-TYPE SYNTAX Unsigned32 (1..255) UNITS "Beacon Intervals" MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents DTIM configuration per WLAN for each 802.11 network. The DTIM value is measured in Beacon Intervals." DEFVAL { 1 } ::= { cLWlanConfigEntry 13 } cLWlanLoadBalancingEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether Load Balancing is enabled on the controller for this WLAN . A value of 'true' indicates Load Balance is on and a value of 'false' indicates Load Balance is turned off for this WLAN." DEFVAL { true } ::= { cLWlanConfigEntry 14 } cLWlanBandSelectEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether Band Select is enabled on the controller for this WLAN. A value of 'true' indicates Band Select is on and a value of 'false' indicates Band Select is turned off for this WLAN." DEFVAL { true } ::= { cLWlanConfigEntry 15 } cLWlanPassiveClientEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether passive client is enabled on the controller for this WLAN. A value of 'true' indicates passive client is on and a value of 'false' indicates passive client is turned off for this WLAN." DEFVAL { false } ::= { cLWlanConfigEntry 16 } cLWlanReAnchorRoamedVoiceClientsEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether the Roamed Voice Client Re-Anchoring feature is enabled on the controller for this WLAN. A value of 'true' indicates the roamed voice clients will get re-anchored. A value of 'false' indicates the roamed voice clients re-anchoring is turned off for this WLAN." DEFVAL { false } ::= { cLWlanConfigEntry 17 } cLWlanMulticastInterfaceEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether multicast interface is enabled on the controller. A value of 'true' indicates that multicast interface feature is enabled and the interface represented by 'cLWlanMulticastInterface' would be used for the multicast traffic on this WLAN. A value of 'false' indicates that multicast interface feature is turned off for this WLAN." DEFVAL { false } ::= { cLWlanConfigEntry 18 } cLWlanMulticastInterface OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the interface, which would be used for the multicast traffic for all the clients that are associated to this WLAN." DEFVAL { "default" } ::= { cLWlanConfigEntry 19 } cLWlanMulticastDirectEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether multicast direct is enabled on the controller for this WLAN. A value of 'true' indicates multicast direct is ON. A value of 'false' indicates multicast direct is turned off for this WLAN." DEFVAL { false } ::= { cLWlanConfigEntry 20 } cLWlanNACPostureSupport OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the NAC-Posture support for the WLAN. A value of 'true' indicates that the WLAN supports the NAC-Posture feature. A value of 'false' indicates that the WLAN does not support the NAC-Posture feature." DEFVAL { false } ::= { cLWlanConfigEntry 21 } cLWlanMaxClientsAccepted OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the maximum number of client connection allowed for this WLAN. A value of 0 indicates that there is no limit on maximum allowed clients for this WLAN." DEFVAL { 0 } ::= { cLWlanConfigEntry 22 } cLWlanScanDeferPriority OBJECT-TYPE SYNTAX BITS { bit0(0), bit1(1), bit2(2), bit3(3), bit4(4), bit5(5), bit6(6), bit7(7) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the priority of packets that defer the off-channel scan. This is used in off-channel scanning to improve performance for medical devices using Radio Resource Management. Each bit represents a packet type for which off-channel scanning needs to be deferred. bit0 - Best effort. bit1 - Background bit2 - Spare bit3 - Excellent effort bit4 - Controlled load bit5 - Video, less than 100-ms latency and jitter bit6 - Voice, less than 10-ms latency and jitter bit7 - Network control" DEFVAL { { bit5 , bit6 } } ::= { cLWlanConfigEntry 23 } cLWlanScanDeferTime OBJECT-TYPE SYNTAX Unsigned32 (0..60000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the minimum number of milliseconds that must elapse without the appearance of a specified packet before the access point radios begin an off-channel scan." DEFVAL { 100 } ::= { cLWlanConfigEntry 24 } cLWlanLanSubType OBJECT-TYPE SYNTAX INTEGER { wirelessLan(1), guestLan(2), remoteLan(3), other(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the sub-type of the LAN created. This has to be congruent with cLWlanIswired. If cLWlanIswired is set to 'true', allowed values are guestLan(2) and remoteLan(3). If cLWlanIswired is set to 'false', allowed value is wirelessLan(1). A value of other(4) will be returned if it doesnt match any values defined here. This value is not configurable." ::= { cLWlanConfigEntry 25 } cLWlanWebAuthOnMacFilterFailureEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the Web based authentication on Mac Filter failure support for the WLAN. A value of 'true' enables Web authentication on MAC filter failure for the WLAN. A value of 'false' disables Web authentication on MAC filter failure for the WLAN." DEFVAL { false } ::= { cLWlanConfigEntry 26 } cLWlanStaticIpTunnelingEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the Static IP Tunneling of clients feature support for the WLAN. A value of 'true' enables static IP Tunneling of client for the WLAN. A value of 'false' disables static IP Tunneling of client for the WLAN." DEFVAL { false } ::= { cLWlanConfigEntry 27 } cLWlanKtsCacSupportEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the KTS CAC support for the WLAN. A value of 'true' enables the KTS based CAC support for this wlan. A value of 'false' disables the KTS based CAC support for this wlan." DEFVAL { false } ::= { cLWlanConfigEntry 28 } cLWlanWifiDirectPolicyStatus OBJECT-TYPE SYNTAX INTEGER { disable(1), allow(2), notAllow(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to allow/disallow wi-fi direct clients to/from joining the infrastructure network. disable(1) - WFD is completely disabled. allow(2) - allow WFD clients disallow(3) - controller rejects association request from WFD clients only if it has P2P IE with concurrency enabled." ::= { cLWlanConfigEntry 29 } cLWlanWebAuthIPv6AclName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the name of the Web Auth IPv6 ACL applied to this WLAN. If it is required to remove the ACL name for a WLAN, it should be set to 'none'. ACL's are applied in the following priority order - interfaces ACLs, WLAN ACLs, client ACLs." ::= { cLWlanConfigEntry 30 } cLWlanHotSpot2Enabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the hotSpot2 feature for this WLAN. A value of 'true' enables the HotSpot2 for this wlan. A value of 'false' disables the HotSpot2 for this wlan." DEFVAL { false } ::= { cLWlanConfigEntry 31 } cLWlanMaxClientsAllowedPerRadio OBJECT-TYPE SYNTAX Unsigned32 (1..200) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the maximum allowed clients per AP radio for a WLAN." DEFVAL { 200 } ::= { cLWlanConfigEntry 32 } cLWlanDhcpDeviceProfiling OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the status of DHCP Device Profiling feature for this WLAN. A value of 'true' enables DHCP Device Profiling on this wlan. A value of 'false' disables DHCP the Device Profiling on this wlan." DEFVAL { false } ::= { cLWlanConfigEntry 33 } cLWlanMacAuthOverDot1xEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the configuration state of authentication failover to Dot1x for the WLAN. A value of 'true' enables mac auth or dot1x for the WLAN. A value of 'false' disables mac auth or dot1x for the WLAN." DEFVAL { false } ::= { cLWlanConfigEntry 34 } cLWlanUserTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the timeout value of user for a WLAN." DEFVAL { 300 } ::= { cLWlanConfigEntry 35 } cLWlanUserIdleThreshold OBJECT-TYPE SYNTAX Unsigned32 UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the user idle threshold value in bytes for a WLAN." DEFVAL { 0 } ::= { cLWlanConfigEntry 36 } cLWlanHttpDeviceProfiling OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the status of HTTP Device Profiling feature for this WLAN. A value of 'true' enables HTTP Device Profiling on this wlan. A value of 'false' disables the HTTP Device Profiling on this wlan." DEFVAL { false } ::= { cLWlanConfigEntry 37 } cLWlanHotSpotClearConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to clear all the configuration related to HotSpot feature at WLAN level. A value of 'enable' would clear the configuration. When queries for the current value, always 'disable' would be returned." DEFVAL { disable } ::= { cLWlanConfigEntry 38 } cLWlanRadiusAuthFourthServer OBJECT-TYPE SYNTAX DisplayString (SIZE (0..21)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Fourth Radius Authentication Server for this wlan." ::= { cLWlanConfigEntry 39 } cLWlanRadiusAuthFifthServer OBJECT-TYPE SYNTAX DisplayString (SIZE (0..21)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Fifth Radius Authentication Server for this wlan." ::= { cLWlanConfigEntry 40 } cLWlanRadiusAuthSixthServer OBJECT-TYPE SYNTAX DisplayString (SIZE (0..21)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Sixth Radius Authentication Server for this wlan." ::= { cLWlanConfigEntry 41 } cLWlanRadiusAcctFourthServer OBJECT-TYPE SYNTAX DisplayString (SIZE (0..21)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Fourth Radius Accounting Server for this wlan." ::= { cLWlanConfigEntry 42 } cLWlanRadiusAcctFifthServer OBJECT-TYPE SYNTAX DisplayString (SIZE (0..21)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Fifth Radius Accounting Server for this wlan." ::= { cLWlanConfigEntry 43 } cLWlanRadiusAcctSixthServer OBJECT-TYPE SYNTAX DisplayString (SIZE (0..21)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Sixth Radius Accounting Server for this wlan." ::= { cLWlanConfigEntry 44 } cLWlanSelfAnchorEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether self anchoring is enabled for the wlan." DEFVAL { false } ::= { cLWlanConfigEntry 64 } cLWlanUniversalAdmin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object allows universal admin mode. to be enabled on a 802.1X/WPA/WPA2 secured WLAN." DEFVAL { false } ::= { cLWlanConfigEntry 65 } cLWlan11acMuMimoEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure 11ac Mu Mimo mode for the WLAN. A value of 'true' enables Mu Mimo mode for the WLAN. A value of 'false' disables Mu Mimo mode for the WLAN." DEFVAL { false } ::= { cLWlanConfigEntry 66 } -- ******************************************************************** -- * WLAN 11u Table -- ******************************************************************** cLWlan11uTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlan11uEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the generic 802.11u configuration for a particular WLAN in a controller. This table has a one-to-one relationship with cLWlanConfigTable. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable." ::= { ciscoLwappWlan11uConfig 1 } cLWlan11uEntry OBJECT-TYPE SYNTAX CLWlan11uEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the generic 802.11u configuration for a WLAN." INDEX { cLWlanIndex } ::= { cLWlan11uTable 1 } CLWlan11uEntry ::= SEQUENCE { cLWlan11uStatus TruthValue, cLWlan11uInternetAccess TruthValue, cLWlan11uNetworkType INTEGER, cLWlan11uVenueGroup INTEGER, cLWlan11uVenueType INTEGER, cLWlan11uVenueName SnmpAdminString, cLWlan11uHessid MacAddress, cLWlan11uNetworkAuthType INTEGER, cLWlan11uIpAddressAvailIpv4 INTEGER, cLWlan11uIpAddressAvailIpv6 INTEGER } cLWlan11uStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the 802.11u support for this WLAN. A value of 'true' indicates that 802.11u support is enabled for this WLAN and a value of 'false' indicates that the support is disabled for this WLAN." DEFVAL { false } ::= { cLWlan11uEntry 1 } cLWlan11uInternetAccess OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the internet access with respect to 802.11u feature for this WLAN. A value of 'true' indicates that internet access is enabled for this WLAN and a value of 'false' indicates that the internet access is disabled for this WLAN." DEFVAL { true } ::= { cLWlan11uEntry 2 } cLWlan11uNetworkType OBJECT-TYPE SYNTAX INTEGER { invalid(1), private(2), privateWithGuestAccess(3), chargeablePublicNetwork(4), freePublicNetwork(5), testOrEquipment(6), wildcard(7), personnalDeviceNetwork(8), emgerencyServiceOnlyNetwork(9), notConfigured(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the network type with respect to 802.11u feature , for this WLAN. invalid (1) : Invalid network type. private(2) : Non-authorized users are not permitted on this network. privateWithGuestAccess(3) : Private network but guest accounts area available. chargeablePublicNetwork(4) : The network is accessible to anyone, however, access to the network requires payment. freePublicNetwork(5) : The network is accessible to anyone and no charges apply for the network use. testOrEquipment(6) : The network is used for test or experimental purposes only. wildcard(6) : Wildcard network type. personnalDeviceNetwork(8) : The network is accessible only by Personnal Device. emgerencyServiceOnlyNetwork(9) : Emergency Service network Type." ::= { cLWlan11uEntry 3 } cLWlan11uVenueGroup OBJECT-TYPE SYNTAX INTEGER { unspecified(1), assembly(2), business(3), educational(4), factoryAndIndustrial(5), institutional(6), mercantile(7), residential(8), storage(9), utilityAndMisc(10), vehicular(11), outdoor(12) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object indicates the venue group with respect to 802.11u feature , for this WLAN." DEFVAL { unspecified } ::= { cLWlan11uEntry 4 } cLWlan11uVenueType OBJECT-TYPE SYNTAX INTEGER { unspecified(1), assembly(2), business(3), educational(4), factoryAndIndustrial(5), institutional(6), mercantile(7), residential(8), storage(9), utilityAndMisc(10), vehicular(11), outdoor(12) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object indicates the venue type within a particular venue group, with respect to 802.11u feature , for this WLAN. The Venue group-Venue Type relationship is per the following table: Venue Group Venue Type Code Venue Description =========== =============== ================= 0 0 Unspecified 0 1-255 Reserved 1 0 Unspecified Assembly 1 1 Arena 1 2 Stadium 1 3 Passenger Terminal (e.g., airport, port, bus station, ferry terminal, train station) 1 4 Amphitheater 1 5 Amusement Park 1 6 Place of Worship 1 7 Convention Center 1 8 Library 1 9 Museum 1 10 Restaurant 1 11 Theater 1 12 Bar 1 13 Coffee Shop 1 14 Zoo or Aquarium 1 15 Emergency Coordination Center 1 16-255 Reserved 2 0 Unspecified Business 2 1 Doctor or Dentist office 2 2 Bank 2 3 Fire Station 2 4 Police Station 2 6 Post Office 2 7 Professional Office 2 8 Research and Development Facility 2 9 Attorney Office 2 10-255 Reserved 3 0 Unspecified Educational 3 1 School, Primary 3 2 School, Secondary 3 3 University or College 3 4-255 Reserved 4 0 Unspecified Factory and Industrial 4 1 Factory 4 2-255 Reserved 5 0 Unspecified Institutional 5 1 Hospital 5 2 Long-Term Care Facility (e.g., Nursing home, Hospice, etc.) 5 3 Alcohol and Drug Re-habilitation Center 5 4 Group Home 5 5 Prison or Jail 5 6-255 Reserved 6 0 Unspecified Mercantile 6 1 Retail Store 6 2 Grocery Market 6 3 Automotive Service Station 6 4-255 Reserved 7 0 Unspecified Residential 7 1 Hotel or Motel 7 2 Dormitory 7 3 Boarding House 7 4-255 Reserved 8 0-255 Reserved 9 0-255 Reserved 10 0 Unspecified Vehicular 10 1 Automobile or Truck 10 2 Airplane 10 3 Bus 10 4 Ferry 10 5 Ship or Boat 10 6 Train 10 7-255 Reserved 11 0 Unspecified Outdoor 11 1 Muni-mesh Network 11 2 City Park 11 3-255 Reserved" DEFVAL { unspecified } ::= { cLWlan11uEntry 5 } cLWlan11uVenueName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This is the venue name defined for this WLAN with respect to 802.11u feature." ::= { cLWlan11uEntry 6 } cLWlan11uHessid OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the Hessid for this WLAN." ::= { cLWlan11uEntry 8 } cLWlan11uNetworkAuthType OBJECT-TYPE SYNTAX INTEGER { acceptance(1), enrollment(2), redirection(3), dnsRedirection(4), notConfigured(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the NetworkAuthType for a WLAN" DEFVAL { notConfigured } ::= { cLWlan11uEntry 9 } cLWlan11uIpAddressAvailIpv4 OBJECT-TYPE SYNTAX INTEGER { notAvailable(1), public(2), portRestricted(3), singleNATPrivate(4), doubleNATPrivate(5), portRestrictedAndSingleNATPrivate(6), portRestrictedAndDoubleNATPrivate(7), unKnown(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the IPv4 Address Availability." DEFVAL { notAvailable } ::= { cLWlan11uEntry 10 } cLWlan11uIpAddressAvailIpv6 OBJECT-TYPE SYNTAX INTEGER { notAvailable(1), available(2), unKnown(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the IPv6 Address Availability." DEFVAL { notAvailable } ::= { cLWlan11uEntry 11 } -- ******************************************************************** -- * WLAN 11u OUI Table -- ******************************************************************** cLWlan11uOuiTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlan11uOuiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the OUI (organizational unique identifier) configuration for a particular WLAN. OUIs are assigned by IEEE. A WLAN can have up to 32 OUIs defined. OUI configuration per WLAN is required for the 802.11u feature to work. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlan11uOuiRowStatus object." ::= { ciscoLwappWlan11uConfig 2 } cLWlan11uOuiEntry OBJECT-TYPE SYNTAX CLWlan11uOuiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the OUI (organizational unique identifier) configuration for a particular WLAN. OUIs are assigned by IEEE. A WLAN can have up to 32 OUIs defined. OUI configuration per WLAN is required for the 802.11u feature to work." INDEX { cLWlanIndex, cLWlan11uOuiIndex } ::= { cLWlan11uOuiTable 1 } CLWlan11uOuiEntry ::= SEQUENCE { cLWlan11uOuiIndex Unsigned32, cLWlan11uOui OCTET STRING, cLWlan11uOuiIsBeacon TruthValue, cLWlan11uOuiRowStatus RowStatus, cLWlan11uOuiStorageType StorageType } cLWlan11uOuiIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies one instance of a OUI on a WLAN.Each WLAN can have up to 32 OUIs defined. Each OUI should be unique." ::= { cLWlan11uOuiEntry 1 } cLWlan11uOui OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6 | 10)) MAX-ACCESS read-create STATUS current DESCRIPTION "The OUI field is a public OUI assigned by the IEEE. Each OUI identifies a roaming consortium (group of SSPs with inter-SSP roaming agreement) or a single SSP.WLAN can have up to 32 OUIs defined. Each OUI defined for a WLAN should be unique. For example the value for Cisco is 004096." ::= { cLWlan11uOuiEntry 2 } cLWlan11uOuiIsBeacon OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure this particular OUI as one of the beacon OUIs. Beacon can carry at most 3 OUIs. User should be able to select 0-3 OUIs (from the already configured OUIs for this WLAN). A value of 'true' indicates that this OUI would be carried in beacon. A value of 'false' indicates that this OUI is not a beacon OUI." DEFVAL { false } ::= { cLWlan11uOuiEntry 3 } cLWlan11uOuiRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular OUI entry in the table." ::= { cLWlan11uOuiEntry 4 } cLWlan11uOuiStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This object represnts the storage type for this conceptual row." DEFVAL { nonVolatile } ::= { cLWlan11uOuiEntry 5 } -- ******************************************************************** -- * WLAN 11u Realm Table -- ******************************************************************** cLWlan11uRealmTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlan11uRealmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the realm (NAI) details per WLAN. In order to provide roaming services, it is necessary to have a standardized method for identifying users. NAI is the user identity submitted by the client during network authentication. Each realm entry should be unique." ::= { ciscoLwappWlan11uConfig 3 } cLWlan11uRealmEntry OBJECT-TYPE SYNTAX CLWlan11uRealmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the realm (NAI) configuration for a particular WLAN.A WLAN can have up to 32 realm defined" INDEX { cLWlanIndex, cLWlan11uRealmIndex } ::= { cLWlan11uRealmTable 1 } CLWlan11uRealmEntry ::= SEQUENCE { cLWlan11uRealmIndex Unsigned32, cLWlan11uRealmName SnmpAdminString, cLWlan11uRealmRowStatus RowStatus } cLWlan11uRealmIndex OBJECT-TYPE SYNTAX Unsigned32 (1..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies, one instance of a realm EAP entry (NAI) on a WLAN. Each realm entry should be unique." ::= { cLWlan11uRealmEntry 1 } cLWlan11uRealmName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the NAI name. In order to provide roaming services, it is necessary to have a standardized method for identifying users. NAI is the user identity submitted by the client during network authentication. In roaming, the purpose of the NAI is to identify the user as well as to assist in the routing of the authentication request. Please note that the NAI may not necessarily be the same as the user's e-mail address or the user identity submitted in an application layer authentication." ::= { cLWlan11uRealmEntry 2 } cLWlan11uRealmRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular realm entry (NAI)from the table" ::= { cLWlan11uRealmEntry 3 } -- ******************************************************************** -- * WLAN 11u Realm Eap Table -- ******************************************************************** cLWlan11uRealmEapTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlan11uRealmEapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the EAP method configured per realm for a particular WLAN. A realm can have up to 4 EAP method defined. The EAP method supported are LEAP,PEAP,EAP-FAST and EAP-TLS." ::= { ciscoLwappWlan11uConfig 4 } cLWlan11uRealmEapEntry OBJECT-TYPE SYNTAX CLWlan11uRealmEapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the EAP method configured per realm for a particular WLAN. A realm can have up to 4 EAP method defined. The EAP method supported are LEAP,PEAP,EAP-FAST and EAP-TLS." INDEX { cLWlanIndex, cLWlan11uRealmIndex, cLWlan11uRealmEapIndex } ::= { cLWlan11uRealmEapTable 1 } CLWlan11uRealmEapEntry ::= SEQUENCE { cLWlan11uRealmEapIndex Unsigned32, cLWlan11uRealmEapMethod INTEGER, cLWlan11uRealmEapRowStatus RowStatus } cLWlan11uRealmEapIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies one instance of a EAP entry configured per a realm for a particular WLAN." ::= { cLWlan11uRealmEapEntry 1 } cLWlan11uRealmEapMethod OBJECT-TYPE SYNTAX INTEGER { none(1), leap(2), peap(3), eapTls(4), eapFast(5), eapSim(6), eapTtls(7), eapAka(8) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the EAP method defined." ::= { cLWlan11uRealmEapEntry 2 } cLWlan11uRealmEapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular EAP entry from the table" ::= { cLWlan11uRealmEapEntry 3 } -- ******************************************************************** -- * WLAN 11u Realm Eap Auth Table -- ******************************************************************** cLWlan11uRealmEapAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlan11uRealmEapAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the authentication method details configured per EAP method for particular realm. There can be up to 10 authentication configuration entries per EAP method." ::= { ciscoLwappWlan11uConfig 5 } cLWlan11uRealmEapAuthEntry OBJECT-TYPE SYNTAX CLWlan11uRealmEapAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the authentication method details configured per EAP method for particular realm. There can be up to 10 authentication configuration entries per EAP method." INDEX { cLWlanIndex, cLWlan11uRealmIndex, cLWlan11uRealmEapIndex, cLWlan11uRealmEapAuthIndex } ::= { cLWlan11uRealmEapAuthTable 1 } CLWlan11uRealmEapAuthEntry ::= SEQUENCE { cLWlan11uRealmEapAuthIndex Unsigned32, cLWlan11uRealmEapAuthMethod INTEGER, cLWlan11uRealmEapAuthParam INTEGER, cLWlan11uRealmEapAuthCredentialType INTEGER, cLWlan11uRealmEapAuthRowStatus RowStatus } cLWlan11uRealmEapAuthIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies one instance of a auth entry configured per a EAP for a particular WLAN." ::= { cLWlan11uRealmEapAuthEntry 1 } cLWlan11uRealmEapAuthMethod OBJECT-TYPE SYNTAX INTEGER { nonEapInnerAuthType(1), innerAuthEapType(2), credentialType(3), tunneledEapCredentialType(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the authentication method defined." DEFVAL { nonEapInnerAuthType } ::= { cLWlan11uRealmEapAuthEntry 2 } cLWlan11uRealmEapAuthParam OBJECT-TYPE SYNTAX INTEGER { none(1), pap(2), chap(3), mschap(4), mschapV2(5), leap(6), peap(7), eapTls(8), eapFast(9), eapSim(10), eapTtls(11), eapAka(12), sim(13), usim(14), nfcSecure(15), hardwareToken(16), softToken(17), certificate(18), usernamePassword(19), reserved(20), anonynous(21), vendorSpecific(22) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the authentication parameter defined for a particular authentication method. The Autentication Parameter and the Authentication Method relationship as follows Method Parameter Description =========== =============== ================= 1 1 Reserved 1 2 PAP 1 3 CHAP 1 4 MSCHAP 1 5 MSCHAPV2 2 6 LEAP 2 7 PEAP 2 8 EAP-TLS 2 9 EAP-FAST 2 10 EAP-SIM 2 11 EAP-TTLS 2 12 EAP-AKA 3 13 SIM 3 14 USIM 3 15 NFCSECURE 3 16 HARDWARE TOKEN 3 17 SOFT TOKEN 3 18 CERTIFICATE 3 19 USERNAME PASSWORD 3 20 RESERVED 3 21 Anonynous 3 22 Vendor Specific" DEFVAL { none } ::= { cLWlan11uRealmEapAuthEntry 3 } cLWlan11uRealmEapAuthCredentialType OBJECT-TYPE SYNTAX INTEGER { sim(1), usim(2), nfcSecure(3), hardwareToken(4), softToken(5), certificate(6), usernamePassword(7), reserved(8), anonynous(9), vendorSpecific(10) } MAX-ACCESS read-create STATUS current DESCRIPTION "This is the credential type defined for a particular authentication method." DEFVAL { sim } ::= { cLWlan11uRealmEapAuthEntry 4 } cLWlan11uRealmEapAuthRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular auth entry from the table" ::= { cLWlan11uRealmEapAuthEntry 5 } -- ******************************************************************** -- * WLAN 11u Domain Table -- ******************************************************************** cLWlan11uDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlan11uDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the Domain Entry configuration for a particular WLAN in a controller. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlan11uDomainRowStatus object" ::= { ciscoLwappWlan11uConfig 6 } cLWlan11uDomainEntry OBJECT-TYPE SYNTAX CLWlan11uDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the Domain configuration for a particular WLAN. A WLAN can have up to 10 domains defined." INDEX { cLWlanIndex, cLWlan11uDomainIndex } ::= { cLWlan11uDomainTable 1 } CLWlan11uDomainEntry ::= SEQUENCE { cLWlan11uDomainIndex Unsigned32, cLWlan11uDomainName SnmpAdminString, cLWlan11uDomainRowStatus RowStatus } cLWlan11uDomainIndex OBJECT-TYPE SYNTAX Unsigned32 (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies one instance of a Domain on a WLAN.Each WLAN can have up to 10 Domains defined. Each Domain should be unique." ::= { cLWlan11uDomainEntry 1 } cLWlan11uDomainName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the domain name for this particular Index." ::= { cLWlan11uDomainEntry 2 } cLWlan11uDomainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular Domain entry in the table." ::= { cLWlan11uDomainEntry 3 } -- ******************************************************************** -- * WLAN 11u 3gpp Table -- ******************************************************************** cLWlan11u3gppTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlan11u3gppEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the 3gpp info configuration for a particular WLAN in a controller. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlan11u3gppRowStatus object" ::= { ciscoLwappWlan11uConfig 7 } cLWlan11u3gppEntry OBJECT-TYPE SYNTAX CLWlan11u3gppEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the Domain configuration for a particular WLAN. A WLAN can have up to 32 operator defined." INDEX { cLWlanIndex, cLWlan11u3gppIndex } ::= { cLWlan11u3gppTable 1 } CLWlan11u3gppEntry ::= SEQUENCE { cLWlan11u3gppIndex Unsigned32, cLWlan11u3gppCountryCode OCTET STRING, cLWlan11u3gppNetworkCode OCTET STRING, cLWlan11u3gppRowStatus RowStatus } cLWlan11u3gppIndex OBJECT-TYPE SYNTAX Unsigned32 (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies one instance of a 3gpp on a WLAN.Each WLAN can have up to 32 3gpps defined. Each 3gpp should be unique." ::= { cLWlan11u3gppEntry 1 } cLWlan11u3gppCountryCode OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "This is the Language defined for this 3gpp Index." ::= { cLWlan11u3gppEntry 2 } cLWlan11u3gppNetworkCode OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "This is the Language defined for this 3gpp Index." ::= { cLWlan11u3gppEntry 3 } cLWlan11u3gppRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular 3gpp entry in the table." ::= { cLWlan11u3gppEntry 4 } -- ******************************************************************** -- * WLAN Service Advertisement Table -- ******************************************************************** cLWlanServiceAdvertisementTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlanServiceAdvertisementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the generic service advertisement configuration for a particular WLAN in a controller. This table has a one-to-one relationship with cLWlanConfigTable. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable." ::= { ciscoLwappWlanServiceAdvertisementConfig 1 } cLWlanServiceAdvertisementEntry OBJECT-TYPE SYNTAX CLWlanServiceAdvertisementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the generic 802.11u configuration for a WLAN." INDEX { cLWlanIndex } ::= { cLWlanServiceAdvertisementTable 1 } CLWlanServiceAdvertisementEntry ::= SEQUENCE { cLWlanServiceAdvertisementStatus TruthValue, cLWlanServiceAdvertisementMsapServerIndex Unsigned32 } cLWlanServiceAdvertisementStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the MSAP status for this WLAN. A value of true enables MSAP for this WLAN. A value of false disbales MSAP for this WLAN." DEFVAL { false } ::= { cLWlanServiceAdvertisementEntry 1 } cLWlanServiceAdvertisementMsapServerIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the Index for the MSAP Server." ::= { cLWlanServiceAdvertisementEntry 5 } cLWlanHotSpot2OperatorTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlanHotSpot2OperatorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the Operator configuration for a particular WLAN in a controller. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlanHotSpot2OperatorRowStatus object" ::= { ciscoLwappWlanHotSpot2Config 1 } cLWlanHotSpot2OperatorEntry OBJECT-TYPE SYNTAX CLWlanHotSpot2OperatorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the Domain configuration for a particular WLAN. A WLAN can have up to 32 operator defined." INDEX { cLWlanIndex, cLWlanHotSpot2OperatorIndex } ::= { cLWlanHotSpot2OperatorTable 1 } CLWlanHotSpot2OperatorEntry ::= SEQUENCE { cLWlanHotSpot2OperatorIndex Unsigned32, cLWlanHotSpot2OperatorName SnmpAdminString, cLWlanHotSpot2OperatorLanguage SnmpAdminString, cLWlanHotSpot2OperatorRowStatus RowStatus } cLWlanHotSpot2OperatorIndex OBJECT-TYPE SYNTAX Unsigned32 (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies one instance of a Operator on a WLAN.Each WLAN can have up to 32 Operators defined. Each Operator should be unique." ::= { cLWlanHotSpot2OperatorEntry 1 } cLWlanHotSpot2OperatorName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the Operator name for this particular Index." ::= { cLWlanHotSpot2OperatorEntry 2 } cLWlanHotSpot2OperatorLanguage OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..3)) MAX-ACCESS read-create STATUS current DESCRIPTION "This is the Language defined for this Operator Index." ::= { cLWlanHotSpot2OperatorEntry 3 } cLWlanHotSpot2OperatorRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular Operator entry in the table." ::= { cLWlanHotSpot2OperatorEntry 4 } cLWlanHotSpot2PortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlanHotSpot2PortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies one instance of Port-Protocol Configuration on a WLAN.Each WLAN can have up to 10 port configuration defined.Each configuration should be unique." ::= { ciscoLwappWlanHotSpot2Config 2 } cLWlanHotSpot2PortConfigEntry OBJECT-TYPE SYNTAX CLWlanHotSpot2PortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the Port-Protocol configuration for a particular WLAN. A WLAN can have up to 10 port configurations defined." INDEX { cLWlanIndex, cLWlanHotSpot2PortConfigIndex } ::= { cLWlanHotSpot2PortConfigTable 1 } CLWlanHotSpot2PortConfigEntry ::= SEQUENCE { cLWlanHotSpot2PortConfigIndex Unsigned32, cLWlanHotSpot2PortConfigIpProtocol INTEGER, cLWlanHotSpot2PortConfigPortNumber INTEGER, cLWlanHotSpot2PortConfigStatus INTEGER, cLWlanHotSpot2PortConfigRowStatus RowStatus } cLWlanHotSpot2PortConfigIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies one instance of a Port Configuration on a WLAN.Each WLAN can have up to 32 Port Configurations defined.Each Port Configuration should be unique." ::= { cLWlanHotSpot2PortConfigEntry 1 } cLWlanHotSpot2PortConfigIpProtocol OBJECT-TYPE SYNTAX INTEGER { icmp(1), ftp(6), ikev2(17), esp(50) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the Port Ip protocol for this index for a WLAN" ::= { cLWlanHotSpot2PortConfigEntry 2 } cLWlanHotSpot2PortConfigPortNumber OBJECT-TYPE SYNTAX INTEGER { icmp-esp(0), ftp(20), ssh(22), ttls-vpn(443), ikev2(500), pptp-vpn(1723), ipsec-nat(4500), voip(5060) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the Port Number for this index for a WLAN. This object indicates the Port Number with respect to an IP Protocol. The Protocol Port Number relationship is per the following table: IP Protocol Port Number Description =========== =============== ================= 1 0 ICMP 6 20 FTP 6 22 SSH 6 443 TLS 6 1723 PPTP-VPN 6 5060 VoIP 17 5060 VoIP 17 4500 IKEv 17 500 IKEv2 50 0 ESP" ::= { cLWlanHotSpot2PortConfigEntry 3 } cLWlanHotSpot2PortConfigStatus OBJECT-TYPE SYNTAX INTEGER { closed(1), open(2), unknown(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the Port Status for this instance for a WLAN" ::= { cLWlanHotSpot2PortConfigEntry 4 } cLWlanHotSpot2PortConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular PortConfig entry in the table." ::= { cLWlanHotSpot2PortConfigEntry 5 } cLWlanHotSpot2ConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlanHotSpot2ConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the generic HotSpot2 configuration for a particular WLAN in a controller. This table has a one-to-one relationship with cLWlanConfigTable. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable." ::= { ciscoLwappWlanHotSpot2Config 3 } cLWlanHotSpot2ConfigEntry OBJECT-TYPE SYNTAX CLWlanHotSpot2ConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the generic HotSpot2 configuration for a WLAN." INDEX { cLWlanIndex } ::= { cLWlanHotSpot2ConfigTable 1 } CLWlanHotSpot2ConfigEntry ::= SEQUENCE { cLWlanHotSpot2WanLinkStatus INTEGER, cLWlanHotSpot2WanSymLinkStatus INTEGER, cLWlanHotSpot2WanDownLinkSpeed Unsigned32, cLWlanHotSpot2WanUpLinkSpeed Unsigned32 } cLWlanHotSpot2WanLinkStatus OBJECT-TYPE SYNTAX INTEGER { linkUp(1), linkDown(2), linkInTestState(3), notConfigured(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the status of the link with respect to WAN metrics configuration." ::= { cLWlanHotSpot2ConfigEntry 1 } cLWlanHotSpot2WanSymLinkStatus OBJECT-TYPE SYNTAX INTEGER { different(1), same(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the symmetry of the link with respect to WAN metrics configuration. A value of 'different(1)' indicates that link speed is different in uplink and downlink(ex:ADSL). A value of 'same(2)' indicates that link speed is same in uplink and downlink(ex:DSL)." ::= { cLWlanHotSpot2ConfigEntry 2 } cLWlanHotSpot2WanDownLinkSpeed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the down link speed of WAN Backhaul in kbps." ::= { cLWlanHotSpot2ConfigEntry 3 } cLWlanHotSpot2WanUpLinkSpeed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the up link speed of WAN Backhaul in kbps." ::= { cLWlanHotSpot2ConfigEntry 4 } cLAPGroupsHyperlocationConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CLAPGroupsHyperlocationConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table for configuring Hyperlocation settings allowed for each AP Group. Each site can have a set of HALO and PakRSSI parameters associated with it." ::= { ciscoLwappAPGroupsHyperlocationConfig 1 } cLAPGroupsHyperlocationConfigEntry OBJECT-TYPE SYNTAX CLAPGroupsHyperlocationConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in cLAPGroupsHyperlocationConfigEntry. cLAPGroupName is mandatory for creating an entry in CLAPGroupsHyperlocationConfigEntry ." INDEX { cLAPGroupName } ::= { cLAPGroupsHyperlocationConfigTable 1 } CLAPGroupsHyperlocationConfigEntry ::= SEQUENCE { cLAPGroupsHyperlocationEnable TruthValue, cLAPGroupsPakRssiThreshold Integer32, cLAPGroupsPakRssiThresholdTrigger Gauge32, cLAPGroupsPakRssiNtpIpAddressType InetAddressType, cLAPGroupsPakRssiNtpAddress InetAddress } cLAPGroupsHyperlocationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the state of Hyperlocation. A value of 'true' indicates that Hyperlocation is enabled. A value of 'false' indicates that Hyperlocation is disabled." DEFVAL { false } ::= { cLAPGroupsHyperlocationConfigEntry 1 } cLAPGroupsPakRssiThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the threshold value for Packet RSSI location feature. Valid range is -100 dbm to -50 dbm." DEFVAL { -100 } ::= { cLAPGroupsHyperlocationConfigEntry 2 } cLAPGroupsPakRssiThresholdTrigger OBJECT-TYPE SYNTAX Gauge32 (1..100) UNITS "dbm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the trigger threshold value for Packet RSSI location feature. Valid range is 1 dbm to 100 dbm." DEFVAL { 10 } ::= { cLAPGroupsHyperlocationConfigEntry 3 } cLAPGroupsPakRssiNtpIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the NTP server IP address type for Packet RSSI location feature." ::= { cLAPGroupsHyperlocationConfigEntry 4 } cLAPGroupsPakRssiNtpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the NTP server IP address for Packet RSSI location feature." ::= { cLAPGroupsHyperlocationConfigEntry 5 } cLAPGroupsPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CLAPGroupsPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table for configuring port settings allowed for each AP Group." ::= { ciscoLwappAPGroupsPortConfig 1 } cLAPGroupsPortConfigEntry OBJECT-TYPE SYNTAX CLAPGroupsPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in cLAPGroupsPortConfigEntry. cLAPGroupName is mandatory for creating a entry in CLAPGroupsPortConfigEntry ." INDEX { cLAPGroupName, cLAPGroupsLANPortNumber } ::= { cLAPGroupsPortConfigTable 1 } CLAPGroupsPortConfigEntry ::= SEQUENCE { cLAPGroupsLANPortNumber Unsigned32, cLAPGroupsLANPortStatus INTEGER, cLAPGroupsLANPortPoeStatus INTEGER, cLAPGroupsLANPortRlanName SnmpAdminString, cLAPGroupsLANPortRowStatus RowStatus } cLAPGroupsLANPortNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies the LAN port number of an AP Group. Each AP Group can have up to 3 LAN ports." ::= { cLAPGroupsPortConfigEntry 1 } cLAPGroupsLANPortStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the LAN port state. A value of 'true' indicates that selected LAN Port is enabled. A value of 'false' indicates that LAN Port is disabled." DEFVAL { disabled } ::= { cLAPGroupsPortConfigEntry 2 } cLAPGroupsLANPortPoeStatus OBJECT-TYPE SYNTAX INTEGER { notsupported(0), disabled(1), enabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the LAN port POE state. A value of 'true' indicates that POE is enabled. A value of 'false' indicates that POE is disabled." DEFVAL { disabled } ::= { cLAPGroupsPortConfigEntry 3 } cLAPGroupsLANPortRlanName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the remote LAN name of the corresponding port." ::= { cLAPGroupsPortConfigEntry 4 } cLAPGroupsLANPortRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This is the status column for this row and used to create and delete specific instances of rows in this table. cLAPGroupName and cLAPGroupsLANPortNumber are mandatory for creating and deleting an entry." ::= { cLAPGroupsPortConfigEntry 5 } cLAPGroupsExtModuleConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CLAPGroupsExtModuleConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table for configuring external module settings allowed for each AP Group. An entry in this table is created for each AP group." ::= { ciscoLwappAPGroupsPortConfig 2 } cLAPGroupsExtModuleConfigEntry OBJECT-TYPE SYNTAX CLAPGroupsExtModuleConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in cLAPGroupsExtModuleConfigEntry. cLAPGroupName is mandatory for creating an entry in CLAPGroupsExtModuleConfigEntry ." INDEX { cLAPGroupName } ::= { cLAPGroupsExtModuleConfigTable 1 } CLAPGroupsExtModuleConfigEntry ::= SEQUENCE { cLAPGroupsExtModuleStatus INTEGER, cLAPGroupsExtModuleRlanName SnmpAdminString } cLAPGroupsExtModuleStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the external module state. A value of 'true' indicates that external module is enabled. A value of 'false' indicates that external module is disabled." DEFVAL { disabled } ::= { cLAPGroupsExtModuleConfigEntry 1 } cLAPGroupsExtModuleRlanName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the remote lan name of the external module." ::= { cLAPGroupsExtModuleConfigEntry 2 } -- ******************************************************************** -- * AP Groups Vlan Config -- ******************************************************************** cLAPGroupsVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CLAPGroupsVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table for the WLAN-interface-mappings and WLAN-NAC settings allowed for each configured site. Each site can have a set of WLANs associated with it. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLAPGroupsVlanConfigRowStatus object." ::= { ciscoLwappAPGroupsVlanConfig 1 } cLAPGroupsVlanConfigEntry OBJECT-TYPE SYNTAX CLAPGroupsVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in cLAPGroupsVlanMappingTable. cLWlanProfileName is mandatory for creating a entry in cLWlanConfigEntry." INDEX { cLAPGroupName, cLWlanProfileName } ::= { cLAPGroupsVlanConfigTable 1 } CLAPGroupsVlanConfigEntry ::= SEQUENCE { cLAPGroupName OCTET STRING, cLAPGroupsVlanMappingInterfaceName OCTET STRING, cLAPGroupNACSupport TruthValue, cLAPGroupsVlanConfigRowStatus RowStatus, cLAPGroupsVlanConfigStorageType StorageType, cLAPGroupsWlanOrderIndex Unsigned32, cLAPGroupsVlanMappingInterfaceNameRev1 OCTET STRING } cLAPGroupName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies a AP group. The string is an unique name assigned to a site." ::= { cLAPGroupsVlanConfigEntry 1 } cLAPGroupsVlanMappingInterfaceName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object represents the interface to be used when a client connects to the 'cLWlanProfileName' WLAN on the AP. When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. cLAPGroupsVlanMappingInterfaceName object is superseded by cLAPGroupsVlanMappingInterfaceNameRev1." ::= { cLAPGroupsVlanConfigEntry 2 } cLAPGroupNACSupport OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the NAC- Out Of Band(OOB) support for this AP groups VLAN. A value of 'true' indicates that the AP group supports the NAC- Out Of Band(OOB) feature. A value of 'false' indicates that the AP group does not support the NAC- Out Of Band(OOB) feature." DEFVAL { false } ::= { cLAPGroupsVlanConfigEntry 3 } cLAPGroupsVlanConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This is the status column for this row and used to create and delete specific instances of rows in this table." ::= { cLAPGroupsVlanConfigEntry 4 } cLAPGroupsVlanConfigStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This object represnts the storage type for this conceptual row." DEFVAL { nonVolatile } ::= { cLAPGroupsVlanConfigEntry 5 } cLAPGroupsWlanOrderIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represnts the position of a wlan in each AP group. When a WLAN is added to an AP group, it will be placed in the lowest available slot in an array of size 16. This index will determine the order in which the WLAN is applied on an AP in that group." ::= { cLAPGroupsVlanConfigEntry 6 } cLAPGroupsVlanMappingInterfaceNameRev1 OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the interface to be used when a client connects to the 'cLWlanProfileName' WLAN on the AP. When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP." ::= { cLAPGroupsVlanConfigEntry 7 } cLAPGroupsVenueConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CLAPGroupsVenueConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table for the configuring Venue details for a configured site." ::= { ciscoLwappAPGroupsVlanConfig 2 } cLAPGroupsVenueConfigEntry OBJECT-TYPE SYNTAX CLAPGroupsVenueConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in cLAPGroupsVlanMappingTable. cLWlanProfileName is mandatory for creating a entry in cLWlanConfigEntry." INDEX { cLAPGroupName } ::= { cLAPGroupsVenueConfigTable 1 } CLAPGroupsVenueConfigEntry ::= SEQUENCE { cLAPGroupsVenueConfigVenueGroup INTEGER, cLAPGroupsVenueConfigVenueType INTEGER, cLAPGroupsVenueConfigVenueName SnmpAdminString, cLAPGroupsVenueConfigLanguage SnmpAdminString, cLAPGroupsOperatingClass BITS } cLAPGroupsVenueConfigVenueGroup OBJECT-TYPE SYNTAX INTEGER { unspecified(1), assembly(2), business(3), educational(4), factoryAndIndustrial(5), institutional(6), mercantile(7), residential(8), storage(9), utilityAndMisc(10), vehicular(11), outdoor(12) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the venue group for this AP Group." DEFVAL { unspecified } ::= { cLAPGroupsVenueConfigEntry 1 } cLAPGroupsVenueConfigVenueType OBJECT-TYPE SYNTAX INTEGER { unspecified(1), unspecifiedAssembly(2), arena(3), stadium(4), passengerTerminal(5), amphitheater(6), amusementPark(7), placeOfWorship(8), conventionCenter(9), library(10), museum(11), restaurant(12), theater(13), bar(14), coffeeShop(15), zooOrAquarium(16), emergencyCoordinationCenter(17), unspecifiedBusiness(18), doctorOrDentistOffice(19), bank(20), fireStation(21), policeStation(22), postOffice(23), professionalOffice(24), researchAndDevelopmentFacility(25), attorneyOffice(26), unspecifiedEducational(27), schoolPrimary(28), schoolSecondary(29), universityOrCollege(30), unspecifiedFactoryAndIndustrial(31), factory(32), unspecifiedInstitutional(33), hospital(34), longTermCareFacility(35), alcoholAndDrugRehabilitationCenter(36), groupHome(37), prisonOrJail(38), unspecifiedMercantile(39), retailStore(40), groceryMarket(41), atomotiveServiceStation(42), shoppingMall(43), gasStation(44), unspecifiedResidential(45), privateResidence(46), hotelOrMotel(47), dormitory(48), boardingHouse(49), unspecifiedStorage(50), unspecifiedUtility(51), unspecifiedVehicular(52), automobileOrTruck(53), airplane(54), bus(55), ferry(56), shipOrBoat(57), train(58), motorBike(59), unspecifiedOutdoor(60), muniMeshNetwork(61), cityPark(62), restArea(63), trafficControl(64), busStop(65), kiosk(66) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the venue type within a particular venue group,for this AP Group. The Venue group-Venue Type relationship is per the following table: Venue Group Venue Type Code Venue Description =========== =============== ================= 0 0 Unspecified 0 1-255 Reserved 1 0 Unspecified Assembly 1 1 Arena 1 2 Stadium 1 3 Passenger Terminal (e.g., airport, port, bus station, ferry terminal, train station) 1 4 Amphitheater 1 5 Amusement Park 1 6 Place of Worship 1 7 Convention Center 1 8 Library 1 9 Museum 1 10 Restaurant 1 11 Theater 1 12 Bar 1 13 Coffee Shop 1 14 Zoo or Aquarium 1 15 Emergency Coordination Center 1 16-255 Reserved 2 0 Unspecified Business 2 1 Doctor or Dentist office 2 2 Bank 2 3 Fire Station 2 4 Police Station 2 6 Post Office 2 7 Professional Office 2 8 Research and Development Facility 2 9 Attorney Office 2 10-255 Reserved 3 0 Unspecified Educational 3 1 School, Primary 3 2 School, Secondary 3 3 University or College 3 4-255 Reserved 4 0 Unspecified Factory and Industrial Factory 4 2-255 Reserved 5 0 Unspecified Institutional 5 1 Hospital 5 2 Long-Term Care Facility (e.g., Nursing home, Hospice, etc.) 5 3 Alcohol and Drug Re-habilitation Center 5 4 Group Home 5 5 Prison or Jail 5 6-255 Reserved 6 0 Unspecified Mercantile 6 1 Retail Store 6 2 Grocery Market 6 3 Automotive Service Station 6 4-255 Reserved 7 0 Unspecified Residential 7 1 Hotel or Motel 7 2 Dormitory 7 3 Boarding House 7 4-255 Reserved 8 0-255 Reserved 9 0-255 Reserved 10 0 Unspecified Vehicular 10 1 Automobile or Truck 10 2 Airplane 10 3 Bus 10 4 Ferry 10 5 Ship or Boat 10 6 Train 10 7-255 Reserved 11 0 Unspecified Outdoor 11 1 Muni-mesh Network 11 2 City Park 11 3-255 Reserved" DEFVAL { unspecified } ::= { cLAPGroupsVenueConfigEntry 2 } cLAPGroupsVenueConfigVenueName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..252)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the venue name defined for this AP Group." ::= { cLAPGroupsVenueConfigEntry 3 } cLAPGroupsVenueConfigLanguage OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..3)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the Language defined for this AP Group." ::= { cLAPGroupsVenueConfigEntry 4 } cLAPGroupsOperatingClass OBJECT-TYPE SYNTAX BITS { class81(0), class83(1), class84(2), class112(3), class113(4), class115(5), class116(6), class117(7), class118(8), class119(9), class120(10), class121(11), class122(12), class123(13), class124(14), class125(15), class126(16), class127(17) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the the group of channels on the frequency band(s) the access network operates." ::= { cLAPGroupsVenueConfigEntry 5 } cLAPGroupsMultipleVenueTable OBJECT-TYPE SYNTAX SEQUENCE OF CLAPGroupsMultipleVenueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for configuring multiple venues for a configured site." ::= { ciscoLwappAPGroupsVlanConfig 3 } cLAPGroupsMultipleVenueEntry OBJECT-TYPE SYNTAX CLAPGroupsMultipleVenueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in cLAPGroupsMultipleVenueTable. cLAPGroupsMultipleVenueLanguage is mandatory for creating a row in this table." INDEX { cLAPGroupName, cLAPGroupsMultipleVenueLanguage } ::= { cLAPGroupsMultipleVenueTable 1 } CLAPGroupsMultipleVenueEntry ::= SEQUENCE { cLAPGroupsMultipleVenueLanguage SnmpAdminString, cLAPGroupsMultipleVenueName SnmpAdminString, cLAPGroupsMultipleVenueRowStatus RowStatus } cLAPGroupsMultipleVenueLanguage OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..3)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is the Language defined for the particular venue name entry." ::= { cLAPGroupsMultipleVenueEntry 1 } cLAPGroupsMultipleVenueName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..252)) MAX-ACCESS read-create STATUS current DESCRIPTION "This is the one of the venue names defined for this AP Group." ::= { cLAPGroupsMultipleVenueEntry 2 } cLAPGroupsMultipleVenueRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular venue entry in the table." ::= { cLAPGroupsMultipleVenueEntry 3 } -- ******************************************************************** -- WLAN Client Configuration -- ******************************************************************** cLWlanConfigClientTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlanConfigClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the WLAN configuration for the 802.11 wireless clients that are associated with the APs that have joined this controller. The creation of a new row in cLWlanConfigTable, through an explicit network management action, results in creation of an entry in this table. Similarly, deletion of a row in cLWlanConfigTable through user action causes the deletion of corresponding row in this table. This table has an one-to-one relationship with cLWlanConfigTable. There exists an entry in this table for each corresponding entry in the cLWlanConfigTable." ::= { ciscoLwappWlanConfig 2 } cLWlanConfigClientEntry OBJECT-TYPE SYNTAX CLWlanConfigClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a conceptual row in this table and provides the information about the clients associated on the WLAN, uniquely identified by the cLWlanIndex." INDEX { cLWlanIndex } ::= { cLWlanConfigClientTable 1 } CLWlanConfigClientEntry ::= SEQUENCE { cLWlanClientAclName DisplayString, cLWlanP2PBlocking INTEGER, cLWlanClientIPv6AclName DisplayString } cLWlanClientAclName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the name of the ACL applied to this WLAN. If it is required to remove the ACL name for a WLAN, it should be set to 'none'. ACL's are applied in the following priority order - interfaces ACLs, WLAN ACLs, client ACLs." ::= { cLWlanConfigClientEntry 1 } cLWlanP2PBlocking OBJECT-TYPE SYNTAX INTEGER { disable(1), drop(2), forwardUp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents per WLAN peer-to-peer blocking behavior on controller. Peer-to-peer blocking means traffic between two clients on same VLAN will not be bridged. disable : Peer-to-peer blocking is disabled and traffic is bridged locally within the controller. drop : The packet will be discarded. forwardUp : The packet will be forwarded on the upstream VLAN. The device 'north' of the controller can then make the decision about what to do with the packet." ::= { cLWlanConfigClientEntry 2 } cLWlanClientIPv6AclName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the name of the IPv6 ACL applied to this WLAN. If it is required to remove the ACL name for a WLAN, it should be set to 'none'. ACL's are applied in the following priority order - interfaces ACLs, WLAN ACLs, client ACLs." ::= { cLWlanConfigClientEntry 3 } -- ******************************************************************** -- WLAN QoS Configuration -- ******************************************************************** cLWlanConfigQosTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlanConfigQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the QoS configuration for the WLAN. The creation of a new row in cLWlanConfigTable, through an explicit network management action, results in creation of an entry in this table. Similarly, deletion of a row in cLWlanConfigTable through user action causes the deletion of corresponding row in this table. This table has an one-to-one relationship with cLWlanConfigTable. There exists an entry in this table for each corresponding entry in the cLWlanConfigTable." ::= { ciscoLwappWlanConfig 3 } cLWlanConfigQosEntry OBJECT-TYPE SYNTAX CLWlanConfigQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a conceptual row in this table and provides the information about the QoS parameters on the WLAN, uniquely identified by the cLWlanIndex." INDEX { cLWlanIndex } ::= { cLWlanConfigQosTable 1 } CLWlanConfigQosEntry ::= SEQUENCE { cLWlanClientDSAverageDataRate Unsigned32, cLWlanClientUSAverageDataRate Unsigned32, cLWlanClientDSBurstDataRate Unsigned32, cLWlanClientUSBurstDataRate Unsigned32, cLWlanClientDSAvgRealTimeDataRate Unsigned32, cLWlanClientUSAvgRealTimeDataRate Unsigned32, cLWlanClientDSBurstRealTimeDataRate Unsigned32, cLWlanClientUSBurstRealTimeDataRate Unsigned32, cLWlanSsidDSAverageDataRate Unsigned32, cLWlanSsidUSAverageDataRate Unsigned32, cLWlanSsidDSBurstDataRate Unsigned32, cLWlanSsidUSBurstDataRate Unsigned32, cLWlanSsidDSAvgRealTimeDataRate Unsigned32, cLWlanSsidUSAvgRealTimeDataRate Unsigned32, cLWlanSsidDSBurstRealTimeDataRate Unsigned32, cLWlanSsidUSBurstRealTimeDataRate Unsigned32 } cLWlanClientDSAverageDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Average Data Rate per user on downstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 1 } cLWlanClientUSAverageDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Average Data Rate per user on upstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 2 } cLWlanClientDSBurstDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Burst Data Rate per user on downstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 3 } cLWlanClientUSBurstDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Burst Data Rate per user on upstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 4 } cLWlanClientDSAvgRealTimeDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies average real time Data Rate per user on downstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 5 } cLWlanClientUSAvgRealTimeDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies average real time Data Rate per user on upstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 6 } cLWlanClientDSBurstRealTimeDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies burst real time Data Rate per user on downstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 7 } cLWlanClientUSBurstRealTimeDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies burst real time Data Rate per user on upstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 8 } cLWlanSsidDSAverageDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Average Data Rate per user on downstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 9 } cLWlanSsidUSAverageDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Average Data Rate per user on upstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 10 } cLWlanSsidDSBurstDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Burst Data Rate per user on downstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 11 } cLWlanSsidUSBurstDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Burst Data Rate per user on upstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 12 } cLWlanSsidDSAvgRealTimeDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies average real time Data Rate per user on downstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 13 } cLWlanSsidUSAvgRealTimeDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies average real time Data Rate per user on upstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 14 } cLWlanSsidDSBurstRealTimeDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies burst real time Data Rate per user on downstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 15 } cLWlanSsidUSBurstRealTimeDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies burst real time Data Rate per user on upstream. Value of 0 indicates the feature is disabled." ::= { cLWlanConfigQosEntry 16 } -- ******************************************************************** -- WLAN IOS Configuration -- ******************************************************************** cLWlanConfigIosTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlanConfigIosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the WLAN configuration for IOS profiles configured on the switch. The creation of a new row in cLWlanConfigTable, through an explicit network management action, results in creation of an entry in this table. Similarly, deletion of a row in cLWlanConfigTable through user action causes the deletion of corresponding row in this table. This table has an one-to-one relationship with cLWlanConfigTable. There exists an entry in this table for each corresponding entry in the cLWlanConfigTable." ::= { ciscoLwappWlanConfig 4 } cLWlanConfigIosEntry OBJECT-TYPE SYNTAX CLWlanConfigIosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a conceptual row in this table and provides the information about the clients associated on the WLAN, uniquely identified by the cLWlanIndex." INDEX { cLWlanIndex } ::= { cLWlanConfigIosTable 1 } CLWlanConfigIosEntry ::= SEQUENCE { cLWlanIosAccountingMethodListName SnmpAdminString, cLWlanIosAuthenticationMethodListName SnmpAdminString, cLWlanIosMacFilteringMethodListName SnmpAdminString, cLWlanIosWebAuthMethodListName SnmpAdminString, cLWlanIosQosUpStreamProfileName SnmpAdminString, cLWlanIosQosDownStreamProfileName SnmpAdminString, cLWlanIngressDHCPOption82Format Unsigned32, cLWlanIngressDHCPOption82Ascii TruthValue, cLWlanIngressDHCPOption82Rid TruthValue, cLWlanIngressDHCPOption82Enable TruthValue, cLWlanIosScanDeferPriority Unsigned32, cLWlanIosWebAuthParameterMapName SnmpAdminString, cLWlanIosQosClientUpStreamProfileName SnmpAdminString, cLWlanIosQosClientDownStreamProfileName SnmpAdminString } cLWlanIosAccountingMethodListName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the method list name used for accounting on this WLAN." ::= { cLWlanConfigIosEntry 1 } cLWlanIosAuthenticationMethodListName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the method list name used for 802.1x authentication on this WLAN. This could be LDAP, RADIUS, LOCAL AUTH." ::= { cLWlanConfigIosEntry 2 } cLWlanIosMacFilteringMethodListName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the method list name used for mac filtering on this WLAN." ::= { cLWlanConfigIosEntry 3 } cLWlanIosWebAuthMethodListName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the method list name used for WEB AUTH on this WLAN." ::= { cLWlanConfigIosEntry 4 } cLWlanIosQosUpStreamProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the profile name used for upstream QOS configuration on this WLAN." ::= { cLWlanConfigIosEntry 5 } cLWlanIosQosDownStreamProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the profile name used for downstream QOS configuration on this WLAN." ::= { cLWlanConfigIosEntry 6 } cLWlanIngressDHCPOption82Format OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the DHCP Option82 format for this WLAN." ::= { cLWlanConfigIosEntry 7 } cLWlanIngressDHCPOption82Ascii OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the DHCP Option82 Ascii option for this WLAN." ::= { cLWlanConfigIosEntry 8 } cLWlanIngressDHCPOption82Rid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the DHCP Option82 Rid option for this WLAN." ::= { cLWlanConfigIosEntry 9 } cLWlanIngressDHCPOption82Enable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the DHCP Option82 state for this WLAN." ::= { cLWlanConfigIosEntry 10 } cLWlanIosScanDeferPriority OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the priority of packets that defer the off-channel scan. This is used in off-channel scanning to improve performance for medical devices using Radio Resource Management. Each bit represents a packet type for which off-channel scanning needs to be deferred." ::= { cLWlanConfigIosEntry 11 } cLWlanIosWebAuthParameterMapName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the web auth parameter name on this WLAN." ::= { cLWlanConfigIosEntry 12 } cLWlanIosQosClientUpStreamProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the profile name used for upstream QOS client configuration on this WLAN." ::= { cLWlanConfigIosEntry 13 } cLWlanIosQosClientDownStreamProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the profile name used for downstream QOS client configuration on this WLAN." ::= { cLWlanConfigIosEntry 14 } -- ******************************************************************** -- * WLAN Flexible Netflow Table -- ******************************************************************** cLWlanFlexibleNetflowTable OBJECT-TYPE SYNTAX SEQUENCE OF CLWlanFlexibleNetflowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the flexible netflow policy details per WLAN for AVC. The creation of a new row in cLWlanFlexibleConfigTable, through an explicit network management action, results in creation of an entry in this table. Similarly, deletion of a row in cLWlanConfigTable through user action causes the deletion of corresponding rows in this table. For each wlan, there will be zero to many instances of flexible netflow policies." ::= { ciscoLwappWlanConfig 5 } cLWlanFlexibleNetflowEntry OBJECT-TYPE SYNTAX CLWlanFlexibleNetflowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a conceptual row in this table and provides the information about the flexible netflow policy types associated on the WLAN, uniquely identified by the cLWlanIndex and cLWlanFlexibleNetflowPolicyTypeIndex." INDEX { cLWlanIndex, cLWlanFlexibleNetflowPolicyTypeIndex } ::= { cLWlanFlexibleNetflowTable 1 } CLWlanFlexibleNetflowEntry ::= SEQUENCE { cLWlanFlexibleNetflowPolicyTypeIndex INTEGER, cLWlanFlexibleNetflowMonitorName SnmpAdminString, cLWlanFlexibleNetflowRowStatus RowStatus } cLWlanFlexibleNetflowPolicyTypeIndex OBJECT-TYPE SYNTAX INTEGER { none(0), ipv4InputPolicy(1), ipv4OutputPolicy(2), ipv6InputPolicy(3), ipv6OutputPolicy(4), datalinkInputPolicy(5), datalinkOutputPolicy(6) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used to set the netflow traffic direction for AVC. none(0) capture no traffic IPV4 Input Policy(1) - IPV4 input policy IPV4OutputPolicy(2) - IPV4 output policy IPV6InputPolicy(3) - IPV6 input policy IPV6OutputPolicy(4) - IPV6 output policy DatalinkInputPolicy(5) - Datalink input policy DatalinkOutputPolicy(6) - Datalink output policy." ::= { cLWlanFlexibleNetflowEntry 1 } cLWlanFlexibleNetflowMonitorName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the flexible netflow monitor name assigned to this WLAN." ::= { cLWlanFlexibleNetflowEntry 2 } cLWlanFlexibleNetflowRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status for creation/deletion of a particular flexible netflow policy entry from the table" ::= { cLWlanFlexibleNetflowEntry 3 } -- ******************************************************************** -- * Compliance statements -- ******************************************************************** ciscoLwappWlanMIBCompliances OBJECT IDENTIFIER ::= { ciscoLwappWlanMIBConform 1 } ciscoLwappWlanMIBGroups OBJECT IDENTIFIER ::= { ciscoLwappWlanMIBConform 2 } ciscoLwappWlanMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappWlanConfigGroup } OBJECT cLWlanRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6) } DESCRIPTION "An implementation is only required to support three of the six enumerated values of the RowStatus textual convention, specifically, 'active', 'createAndGo' and 'destroy'." ::= { ciscoLwappWlanMIBCompliances 1 } ciscoLwappWlanMIBComplianceRev1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappWlanConfigGroupSup1, ciscoLwappWlanConfigClientGroup } OBJECT cLWlanRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6) } DESCRIPTION "An implementation is only required to support three of the six enumerated values of the RowStatus textual convention, specifically, 'active', 'createAndGo' and 'destroy'." ::= { ciscoLwappWlanMIBCompliances 2 } ciscoLwappWlanMIBComplianceRev2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappWlanConfigGroupSup1, ciscoLwappWlanConfigClientGroup, ciscoLwappWlan11uConfigGroup, ciscoLwappAPGroupsVlanConfigGroup, ciscoLwappWlanConfigGroupSup2, ciscoLwappWlanConfigClientGroupSup1 } OBJECT cLAPGroupsVlanConfigRowStatus SYNTAX RowStatus DESCRIPTION "An implementation is only required to support three of the six enumerated values of the RowStatus textual convention, specifically, 'active', 'createAndGo' and 'destroy'." OBJECT cLWlan11uOuiRowStatus SYNTAX RowStatus DESCRIPTION "An implementation is only required to support three of the six enumerated values of the RowStatus textual convention, specifically, 'active', 'createAndGo' and 'destroy'." ::= { ciscoLwappWlanMIBCompliances 3 } ciscoLwappWlanMIBComplianceRev3 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappWlanConfigGroupSup1, ciscoLwappWlanConfigClientGroup, ciscoLwappWlan11uConfigGroup, ciscoLwappAPGroupsVlanConfigGroup, ciscoLwappWlanConfigGroupSup2, ciscoLwappWlanConfigClientGroupSup1, ciscoLwappWlanConfigGroupSup3 } ::= { ciscoLwappWlanMIBCompliances 4 } ciscoLwappWlanMIBComplianceRev4 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappWlanConfigGroupSup1, ciscoLwappWlanConfigClientGroup, ciscoLwappAPGroupsVlanConfigGroup, ciscoLwappWlanConfigGroupSup2, ciscoLwappWlanConfigClientGroupSup1, ciscoLwappWlanConfigGroupSup3, ciscoLwappWlan11uConfigGroupsup1, ciscoLwappWlanServiceAdvertisementConfigGroup, ciscoLwappWlanHotSpot2ConfigGroup, ciscoLwappWlanIosConfigGroup, ciscoLwappWlanQosConfigGroup, ciscoLwappWlan11uConfigGroupsup2, ciscoLwappWlanConfigGroupSup4, ciscoLwappWlanHotSpot2ConfigGroupSup1, ciscoLwappAPGroupsVlanConfigGroupSup1, cLAPGroupsVenueConfigGroup, cLAPGroupsMultipleVenueGroup, ciscoLwappWlanConfigClientGroupSup2 } ::= { ciscoLwappWlanMIBCompliances 5 } ciscoLwappWlanMIBComplianceRev5 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappWlanConfigGroupSup1, ciscoLwappWlanConfigClientGroup, ciscoLwappAPGroupsVlanConfigGroup, ciscoLwappWlanConfigGroupSup2, ciscoLwappWlanConfigClientGroupSup1, ciscoLwappWlanConfigGroupSup3, ciscoLwappWlan11uConfigGroupsup1, ciscoLwappWlanServiceAdvertisementConfigGroup, ciscoLwappWlanHotSpot2ConfigGroup, ciscoLwappWlanIosConfigGroup, ciscoLwappWlanQosConfigGroup, ciscoLwappWlan11uConfigGroupsup2, ciscoLwappWlanConfigGroupSup4, ciscoLwappWlanHotSpot2ConfigGroupSup1, ciscoLwappAPGroupsVlanConfigGroupSup1, cLAPGroupsVenueConfigGroup, cLAPGroupsMultipleVenueGroup, ciscoLwappWlanConfigClientGroupSup2, ciscoLwappWlanConfigFlexibleNetflowGroup } ::= { ciscoLwappWlanMIBCompliances 6 } ciscoLwappWlanMIBComplianceRev6 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappWlanConfigGroupSup1, ciscoLwappWlanConfigClientGroup, ciscoLwappWlanConfigGroupSup2, ciscoLwappWlanConfigClientGroupSup1, ciscoLwappWlanConfigGroupSup3, ciscoLwappWlan11uConfigGroupsup1, ciscoLwappWlanServiceAdvertisementConfigGroup, ciscoLwappWlanHotSpot2ConfigGroup, ciscoLwappWlanIosConfigGroup, ciscoLwappWlanQosConfigGroup, ciscoLwappWlan11uConfigGroupsup2, ciscoLwappWlanConfigGroupSup4, ciscoLwappWlanHotSpot2ConfigGroupSup1, ciscoLwappAPGroupsVlanConfigGroupSup1, cLAPGroupsVenueConfigGroup, cLAPGroupsMultipleVenueGroup, ciscoLwappWlanConfigClientGroupSup2, ciscoLwappWlanConfigFlexibleNetflowGroup, ciscoLwappAPGroupsVlanConfigGroupSup2 } ::= { ciscoLwappWlanMIBCompliances 7 } ciscoLwappWlanMIBComplianceRev7 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappWlanConfigGroupSup1, ciscoLwappWlanConfigClientGroup, ciscoLwappWlanConfigGroupSup2, ciscoLwappWlanConfigClientGroupSup1, ciscoLwappWlanConfigGroupSup3, ciscoLwappWlan11uConfigGroupsup1, ciscoLwappWlanServiceAdvertisementConfigGroup, ciscoLwappWlanHotSpot2ConfigGroup, ciscoLwappWlanIosConfigGroup, ciscoLwappWlanQosConfigGroup, ciscoLwappWlan11uConfigGroupsup2, ciscoLwappWlanConfigGroupSup4, ciscoLwappWlanHotSpot2ConfigGroupSup1, ciscoLwappAPGroupsVlanConfigGroupSup1, cLAPGroupsVenueConfigGroup, cLAPGroupsMultipleVenueGroup, ciscoLwappWlanConfigClientGroupSup2, ciscoLwappWlanConfigFlexibleNetflowGroup, ciscoLwappAPGroupsVlanConfigGroupSup2, ciscoLwappWlanConfigGroupSup6 } ::= { ciscoLwappWlanMIBCompliances 8 } ciscoLwappWlanMIBComplianceRev8 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappWlanConfigGroupSup1, ciscoLwappWlanConfigClientGroup, ciscoLwappWlanConfigGroupSup2, ciscoLwappWlanConfigClientGroupSup1, ciscoLwappWlanConfigGroupSup3, ciscoLwappWlan11uConfigGroupsup1, ciscoLwappWlanServiceAdvertisementConfigGroup, ciscoLwappWlanHotSpot2ConfigGroup, ciscoLwappWlanIosConfigGroup, ciscoLwappWlanQosConfigGroup, ciscoLwappWlan11uConfigGroupsup2, ciscoLwappWlanConfigGroupSup4, ciscoLwappWlanHotSpot2ConfigGroupSup1, ciscoLwappAPGroupsVlanConfigGroupSup1, cLAPGroupsVenueConfigGroup, cLAPGroupsMultipleVenueGroup, ciscoLwappWlanConfigClientGroupSup2, ciscoLwappWlanConfigFlexibleNetflowGroup, ciscoLwappAPGroupsVlanConfigGroupSup2, ciscoLwappWlanConfigGroupSup6, ciscoLwappWlanConfigGroupSup7, ciscoLwappWlanConfigGroupSup8 } ::= { ciscoLwappWlanMIBCompliances 9 } -- ******************************************************************** -- * Units of conformance -- ******************************************************************** ciscoLwappWlanConfigGroup OBJECT-GROUP OBJECTS { cLWlanRowStatus } STATUS deprecated DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP. ciscoLwappWlanConfigGroup object is superseded by ciscoLwappWlanConfigGroupSup1." ::= { ciscoLwappWlanMIBGroups 1 } ciscoLwappWlanConfigGroupSup1 OBJECT-GROUP OBJECTS { cLWlanRowStatus, cLWlanProfileName, cLWlanSsid, cLWlanDiagChan, cLWlanStorageType } STATUS current DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP." ::= { ciscoLwappWlanMIBGroups 2 } ciscoLwappWlanConfigClientGroup OBJECT-GROUP OBJECTS { cLWlanClientAclName } STATUS current DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an 8021.11 clients." ::= { ciscoLwappWlanMIBGroups 3 } ciscoLwappWlan11uConfigGroup OBJECT-GROUP OBJECTS { cLWlan11uStatus, cLWlan11uInternetAccess, cLWlan11uNetworkType, cLWlan11uVenueGroup, cLWlan11uVenueType, cLWlan11uVenueName, cLWlan11uOui, cLWlan11uOuiIsBeacon, cLWlan11uOuiRowStatus, cLWlan11uOuiStorageType } STATUS deprecated DESCRIPTION "This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP. ciscoLwappWlan11uConfigGroup object is superseded by ciscoLwappWlan11uConfigGroupsup1." ::= { ciscoLwappWlanMIBGroups 4 } ciscoLwappAPGroupsVlanConfigGroup OBJECT-GROUP OBJECTS { cLAPGroupsVlanMappingInterfaceName, cLAPGroupNACSupport, cLAPGroupsVlanConfigRowStatus, cLAPGroupsVlanConfigStorageType } STATUS deprecated DESCRIPTION "This collection of objects represent the configuration of AP Groups Vlan on the controller to be passed to an AP. ciscoLwappAPGroupsVlanConfigGroup object is superseded by ciscoLwappAPGroupsVlanConfigGroupSup2." ::= { ciscoLwappWlanMIBGroups 5 } ciscoLwappWlanConfigGroupSup2 OBJECT-GROUP OBJECTS { cLWlanLoadBalancingEnable, cLWlanBandSelectEnable, cLWlanPassiveClientEnable, cLWlanIsWired, cLWlanIngressInterface, cLWlanNACSupport, cLWlanWepKeyChange, cLWlanChdEnable, cLWlan802dot11anDTIM, cLWlan802dot11bgnDTIM } STATUS current DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP." ::= { ciscoLwappWlanMIBGroups 6 } ciscoLwappWlanConfigClientGroupSup1 OBJECT-GROUP OBJECTS { cLWlanP2PBlocking } STATUS current DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an 8021.11 clients." ::= { ciscoLwappWlanMIBGroups 7 } ciscoLwappWlanConfigGroupSup3 OBJECT-GROUP OBJECTS { cLWlanReAnchorRoamedVoiceClientsEnable, cLWlanMulticastInterfaceEnable, cLWlanMulticastInterface, cLWlanMulticastDirectEnable, cLWlanNACPostureSupport, cLWlanMaxClientsAccepted, cLWlanScanDeferPriority, cLWlanScanDeferTime, cLWlanLanSubType, cLWlanWebAuthOnMacFilterFailureEnabled, cLWlanStaticIpTunnelingEnabled } STATUS current DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP." ::= { ciscoLwappWlanMIBGroups 8 } ciscoLwappWlan11uConfigGroupsup1 OBJECT-GROUP OBJECTS { cLWlan11uStatus, cLWlan11uInternetAccess, cLWlan11uNetworkType, cLWlan11uHessid, cLWlan11uNetworkAuthType, cLWlan11uOui, cLWlan11uOuiIsBeacon, cLWlan11uOuiRowStatus, cLWlan11uOuiStorageType, cLWlan11uRealmName, cLWlan11uRealmRowStatus, cLWlan11uRealmEapMethod, cLWlan11uRealmEapRowStatus, cLWlan11uRealmEapAuthMethod, cLWlan11uRealmEapAuthParam, cLWlan11uRealmEapAuthRowStatus, cLWlan11uDomainName, cLWlan11uDomainRowStatus, cLWlan11u3gppCountryCode, cLWlan11u3gppNetworkCode, cLWlan11u3gppRowStatus, cLWlan11uIpAddressAvailIpv4, cLWlan11uIpAddressAvailIpv6 } STATUS current DESCRIPTION "This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 9 } ciscoLwappWlanServiceAdvertisementConfigGroup OBJECT-GROUP OBJECTS { cLWlanServiceAdvertisementStatus, cLWlanServiceAdvertisementMsapServerIndex } STATUS current DESCRIPTION "This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 10 } ciscoLwappWlanHotSpot2ConfigGroup OBJECT-GROUP OBJECTS { cLWlanHotSpot2OperatorName, cLWlanHotSpot2OperatorLanguage, cLWlanHotSpot2OperatorRowStatus, cLWlanHotSpot2PortConfigIpProtocol, cLWlanHotSpot2PortConfigPortNumber, cLWlanHotSpot2PortConfigStatus, cLWlanHotSpot2PortConfigRowStatus } STATUS current DESCRIPTION "This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 11 } ciscoLwappWlanIosConfigGroup OBJECT-GROUP OBJECTS { cLWlanIosAccountingMethodListName, cLWlanIosAuthenticationMethodListName, cLWlanIosMacFilteringMethodListName, cLWlanIosWebAuthMethodListName, cLWlanIosQosUpStreamProfileName, cLWlanIosQosDownStreamProfileName, cLWlanIngressDHCPOption82Format, cLWlanIngressDHCPOption82Ascii, cLWlanIngressDHCPOption82Rid, cLWlanIngressDHCPOption82Enable, cLWlanIosScanDeferPriority, cLWlanIosWebAuthParameterMapName, cLWlanIosQosClientUpStreamProfileName, cLWlanIosQosClientDownStreamProfileName } STATUS current DESCRIPTION "This collection of objects represents IOS related configuration of WLANs on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 12 } ciscoLwappWlanQosConfigGroup OBJECT-GROUP OBJECTS { cLWlanClientDSAverageDataRate, cLWlanClientUSAverageDataRate, cLWlanClientDSBurstDataRate, cLWlanClientUSBurstDataRate, cLWlanClientDSAvgRealTimeDataRate, cLWlanClientUSAvgRealTimeDataRate, cLWlanClientDSBurstRealTimeDataRate, cLWlanClientUSBurstRealTimeDataRate, cLWlanSsidDSAverageDataRate, cLWlanSsidUSAverageDataRate, cLWlanSsidDSBurstDataRate, cLWlanSsidUSBurstDataRate, cLWlanSsidDSAvgRealTimeDataRate, cLWlanSsidUSAvgRealTimeDataRate, cLWlanSsidDSBurstRealTimeDataRate, cLWlanSsidUSBurstRealTimeDataRate } STATUS current DESCRIPTION "This collection of objects represents QoS related configuration of WLANs on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 13 } ciscoLwappWlanConfigGroupSup4 OBJECT-GROUP OBJECTS { cLWlanKtsCacSupportEnabled, cLWlanWifiDirectPolicyStatus, cLWlanWebAuthIPv6AclName, cLWlanHotSpot2Enabled, cLWlanMaxClientsAllowedPerRadio, cLWlanDhcpDeviceProfiling, cLWlanMacAuthOverDot1xEnabled, cLWlanUserTimeout, cLWlanUserIdleThreshold, cLWlanHttpDeviceProfiling, cLWlanHotSpotClearConfig, cLWlanRadiusAuthFourthServer, cLWlanRadiusAuthFifthServer, cLWlanRadiusAuthSixthServer, cLWlanRadiusAcctFourthServer, cLWlanRadiusAcctFifthServer, cLWlanRadiusAcctSixthServer, cLWlanSelfAnchorEnabled } STATUS deprecated DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP.This object is superceded by ciscoLwappWlanConfigGroupSup5. ciscoLwappWlanConfigGroupSup4 object is superseded by ciscoLwappWlanConfigGroupSup5." ::= { ciscoLwappWlanMIBGroups 14 } ciscoLwappWlan11uConfigGroupsup2 OBJECT-GROUP OBJECTS { cLWlan11uRealmEapAuthCredentialType } STATUS current DESCRIPTION "This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 15 } ciscoLwappWlanHotSpot2ConfigGroupSup1 OBJECT-GROUP OBJECTS { cLWlanHotSpot2WanLinkStatus, cLWlanHotSpot2WanSymLinkStatus, cLWlanHotSpot2WanDownLinkSpeed, cLWlanHotSpot2WanUpLinkSpeed } STATUS current DESCRIPTION "This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 16 } ciscoLwappAPGroupsVlanConfigGroupSup1 OBJECT-GROUP OBJECTS { cLAPGroupsWlanOrderIndex } STATUS current DESCRIPTION "This collection of objects represent the configuration of AP Groups Vlan on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 17 } cLAPGroupsVenueConfigGroup OBJECT-GROUP OBJECTS { cLAPGroupsVenueConfigVenueGroup, cLAPGroupsVenueConfigVenueType, cLAPGroupsVenueConfigVenueName, cLAPGroupsVenueConfigLanguage, cLAPGroupsOperatingClass } STATUS current DESCRIPTION "This collection of objects represent the configuration of Venue groups on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 18 } cLAPGroupsMultipleVenueGroup OBJECT-GROUP OBJECTS { cLAPGroupsMultipleVenueName, cLAPGroupsMultipleVenueRowStatus } STATUS current DESCRIPTION "This collection of objects represent the configuration of Venue groups on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 19 } ciscoLwappWlanConfigClientGroupSup2 OBJECT-GROUP OBJECTS { cLWlanClientIPv6AclName } STATUS current DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an 8021.11 clients." ::= { ciscoLwappWlanMIBGroups 20 } ciscoLwappWlanConfigFlexibleNetflowGroup OBJECT-GROUP OBJECTS { cLWlanFlexibleNetflowMonitorName, cLWlanFlexibleNetflowRowStatus } STATUS current DESCRIPTION "This collection of objects represent the configuration of flexible netflow policy details per WLAN on the conroller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 21 } ciscoLwappWlanConfigGroupSup5 OBJECT-GROUP OBJECTS { cLWlanKtsCacSupportEnabled, cLWlanWifiDirectPolicyStatus, cLWlanWebAuthIPv6AclName, cLWlanHotSpot2Enabled, cLWlanMaxClientsAllowedPerRadio, cLWlanDhcpDeviceProfiling, cLWlanMacAuthOverDot1xEnabled, cLWlanUserTimeout, cLWlanUserIdleThreshold, cLWlanHttpDeviceProfiling, cLWlanHotSpotClearConfig, cLWlanRadiusAuthFourthServer, cLWlanRadiusAuthFifthServer, cLWlanRadiusAuthSixthServer, cLWlanRadiusAcctFourthServer, cLWlanRadiusAcctFifthServer, cLWlanRadiusAcctSixthServer, cLWlanSelfAnchorEnabled, cLWlanUniversalAdmin } STATUS current DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP." ::= { ciscoLwappWlanMIBGroups 22 } ciscoLwappAPGroupsVlanConfigGroupSup2 OBJECT-GROUP OBJECTS { cLAPGroupNACSupport, cLAPGroupsVlanConfigRowStatus, cLAPGroupsVlanConfigStorageType, cLAPGroupsVlanMappingInterfaceNameRev1 } STATUS current DESCRIPTION "This collection of objects represent the configuration of AP Groups Vlan on the controller to be passed to an AP." ::= { ciscoLwappWlanMIBGroups 23 } ciscoLwappWlanConfigGroupSup6 OBJECT-GROUP OBJECTS { cLWlan11acMuMimoEnabled } STATUS current DESCRIPTION "This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP." ::= { ciscoLwappWlanMIBGroups 24 } ciscoLwappWlanConfigGroupSup7 OBJECT-GROUP OBJECTS { cLAPGroupsHyperlocationEnable, cLAPGroupsPakRssiThreshold, cLAPGroupsPakRssiThresholdTrigger, cLAPGroupsPakRssiNtpIpAddressType, cLAPGroupsPakRssiNtpAddress } STATUS current DESCRIPTION "This collection of objects represent the configuration of AP Groups HyperLocation on the controller to be passed to an LWAPP AP." ::= { ciscoLwappWlanMIBGroups 25 } ciscoLwappWlanConfigGroupSup8 OBJECT-GROUP OBJECTS { cLAPGroupsLANPortStatus, cLAPGroupsLANPortPoeStatus, cLAPGroupsLANPortRlanName, cLAPGroupsLANPortRowStatus, cLAPGroupsExtModuleStatus, cLAPGroupsExtModuleRlanName } STATUS current DESCRIPTION "This collection of objects represent the configuration of AP Groups LAN Port on the controller to be passed to an LWAPP AP." ::= { ciscoLwappWlanMIBGroups 26 } END