-- ***************************************************************** -- CISCO-SP-MIB: Mib for SS7 SP support entities -- -- January 2001, Mauro Zallocco, John Linton, Shekhar Acharya -- -- Copyright (c) 2001-2005 by Cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** -- -- Caution. This MIB is temporary and experimental. In the future it -- will be removed from products, perhaps with short notice, in favor -- of more standard or generic MIBs. Application developers should not -- depend on long-term access to this MIB. -- -- ***************************************************************** CISCO-SP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-TYPE, Counter32, Counter64, Integer32, Gauge32, TimeTicks, Unsigned32 FROM SNMPv2-SMI InterfaceIndexOrZero FROM CISCO-TC DisplayString, TimeStamp, TruthValue, TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ciscoExperiment FROM CISCO-SMI; ciscoSpMIB MODULE-IDENTITY LAST-UPDATED "200601160000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems, Inc Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-ss7@cisco.com" DESCRIPTION "The MIB for managing the SS7 Signalling Point (SP) implemented in the Cisco IOS SS7 offload product. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the SP as follows: The SP is associated with one or more point codes. Each pointcode is associated with: an ss7 variant, timers, and linksets. Linksets contain: destination point code linkset byte/packet statistics, accounting information per DPC and OPC violation accounting information per DPC and OPC links, reference to incoming and outgoing ACL reference to a routing table for each SS7 packet type Links contain: timers, and byte/packet statistics. The figure below provides a diagrammatic representation of the relationships. Each box may be replicated providing multiple instances of the object. '--->' indicates that the object to the left contains a reference to the object to the right. '###>' indicates that the object to the left contains an instance of the object to the right. The down arrow indicates that the object being pointed to contains snmp indices of the objects above it. ________________ | | | Sp |###> point code, timers |________________| | V ________________ | | | |---> Accounting | Linkset |---> Violation Accounting | |---> Incoming ACL | |---> Outgoing ACL |________________|---> Routing Tables. | V ________________ | Link |###> timers |________________|---> statistics " REVISION "200601160000Z" DESCRIPTION "The CISCO-SP-MIB is obsolete and has been replaced by the combination of the CISCO-ITP-TC-MIB and CISCO-ITP-GSP-MIB. Updated the mib to import Unsigned32 from SNMPv2-SMI instead of CISCO-TC. Modified the syntax of CSpRouteTableName and CSpLinksetId to OCTET STRING. Changed the order of objects in cSpAccountingTableEntry SEQUENCE. Added the notification group ciscoSpNotificationsGroup and included it in the MODULE-COMPLIANCE as optional." REVISION "200106070000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoExperiment 73 } -- Top-level structure of the MIB ciscoSpMIBObjects OBJECT IDENTIFIER ::= { ciscoSpMIB 1 } cSpScalars OBJECT IDENTIFIER ::= { ciscoSpMIBObjects 1 } cSpLinkset OBJECT IDENTIFIER ::= { ciscoSpMIBObjects 2 } cSpLink OBJECT IDENTIFIER ::= { ciscoSpMIBObjects 3 } cSpRoute OBJECT IDENTIFIER ::= { ciscoSpMIBObjects 4 } cSpAccessControlList OBJECT IDENTIFIER ::= { ciscoSpMIBObjects 5 } cSpAccounting OBJECT IDENTIFIER ::= { ciscoSpMIBObjects 6 } cSpNotificationsEnable OBJECT IDENTIFIER ::= { ciscoSpMIBObjects 7 } -- ******************************************************************** -- * * -- * Textual Conventions * -- * * -- ******************************************************************** CSpPointCode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The SS7 network node address as specified in the International Telecommunication Union standard Q.708: Specifications of Signalling System No. 7 - Numbering of International Signalling Point Codes, and by ANSI T1.111.8 Numbering of Signalling Point Codes." SYNTAX Unsigned32 ( 0..16777216 ) CSpSs7Variant ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The list of SS7 variants. 'ANSI' : The ANSI variant of the SS7 specification. 'ITU' : The ITU variant of the SS7 specification." SYNTAX INTEGER { ansi(1), itu(2) } CSpLinkType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The link types. 'other' : This link is of some type not listed below. 'serial' : This link is an serial link transporting SS7 traffic. 'sctpIp' : This a SCTP/IP link." SYNTAX INTEGER { other(1), serial(2), sctpIp(3) } CSpLinkSLC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Signalling Link Code. This is the link identifier within a linkset." SYNTAX Unsigned32 ( 0..15 ) CSpLinksetId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The configured name associated with an Sp Linkset." SYNTAX OCTET STRING ( SIZE ( 1..19 ) ) CSpAclAction ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The list of possible actions to be performed on a packet who's point code matches an access control. 'accept' : The matching packet is accepted for further processing. 'discard' : The matching packet is to be discarded without any further processing on this packet." SYNTAX INTEGER { accept(1), discard(2) } CSpOsiState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The list of possible link/linkset statuses. 'active' : Traffic may flow over this link/linkset 'inactive' : Traffic cannot flow over this link/linkset. 'inhibited' : Traffic cannot flow over this link/linkset. This state was reached as a result of administrative action. 'uninhibited': The link/linkset is available at the MTP3 layer. 'shut ': The link/linkset has been forced to an unavailable state by an administrative action. 'noshut ': The link/linkset has been removed from an unavailable state by an administrative action." SYNTAX INTEGER { active(1), inactive(2), inhibited(3), uninhibited(4), shut(5), noshut(6) } CSpAclId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An numeric Identifier used to specify and access list used to permit and deny packets based on MTP3 information." SYNTAX Unsigned32(0..2999) CSpRouteTableName ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The configured name associated with an SP Route Table." SYNTAX OCTET STRING ( SIZE (1..19) ) CSpAclSi ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The list of possible Service Indicator values. This identifies the type of SS7 packet. The service indicator codes for the international signalling network are allocated as follows: 0 Signalling network management messages (SNMM) 1 Signalling network testing and maintenance messages (SNTM) 2 Spare 2 3 SCCP 4 Telephone User Part (TUP) 5 ISDN User Part (ISUP) 6 Data User Part, call and circuit-related messages (DUPC) 7 Data User Part, facility registration and cancellation messages (DUPF) 8 Reserved for MTP Testing User Part (MTUP) 9 Broadband ISDN User Part (BISUP) 10 Satellite ISDN User Part (SISUP) 11 Spare 12 Spare 13 Spare 14 Spare 15 Spare Reference: ITU Q.704 Signalling network functions and messages section 14.2.1 Service indicator. " SYNTAX Unsigned32 ( 0..15 ) CSpRouteStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The status of the route from the perspective of the SP. 'available' : Route is available for routing of packets. 'restricted' : Route has been restricted from routing. 'unavailable' : Route is unavailable for routing of packets." SYNTAX INTEGER { available(1), restricted(2), unavailable(3) } -- ************************************************************* -- * * -- * SP - Scalers * -- * * -- ************************************************************* cSpSs7Variant OBJECT-TYPE SYNTAX CSpSs7Variant MAX-ACCESS read-only STATUS current DESCRIPTION "The SS7 variant implemented in this SP." ::= { cSpScalars 1 } cSpPointCode OBJECT-TYPE SYNTAX CSpPointCode MAX-ACCESS read-only STATUS current DESCRIPTION "The point code for this SP." ::= { cSpScalars 2 } cSpMtp2T01 OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Alignment ready timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 3 } cSpMtp2T02 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Not aligned timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial. A get on this object will return a zero if cSpLinkType is not serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 4 } cSpMtp2T03 OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Aligned timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 5 } cSpMtp2T4N OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Proving period timer normal timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. " REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 6 } cSpMtp2T4E OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Proving period timer emergency timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 7 } cSpMtp2T05 OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Sending SIB timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 8 } cSpMtp2T06 OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Remote congestion timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 9 } cSpMtp2T07 OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Excessive delay of acknowledgement timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 10 } cSpMtp2T08 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Interval timer for error interval monitor." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 11 } cSpMtp3T01 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Delay to avoid message mis-sequencing on changeover." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 12 } cSpMtp3T02 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for changeover acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 13 } cSpMtp3T03 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Time controlled diversion-delay to avoid mis-sequencing on change back." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 14 } cSpMtp3T04 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for change back acknowledgement (first attempt)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 15 } cSpMtp3T05 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for change back acknowledgement (second attempt)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 16 } cSpMtp3T06 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Delay to avoid message mis-sequencing on controlled rerouting." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 17 } cSpMtp3T07 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for signalling data link connection acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 18 } cSpMtp3T08 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Transfer prohibited inhibition timer (transient solution)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 19 } cSpMtp3T10 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting to repeat signalling routeset test message." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 20 } cSpMtp3T11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Transfer restricted timer. (This is one way of implementing the function described in 13.4/Q.704 and mainly intended to simplify SPs.)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 21 } cSpMtp3T12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for uninhibit acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 22 } cSpMtp3T13 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for force uninhibit." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 23 } cSpMtp3T14 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for inhibition acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 24 } cSpMtp3T15 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting to start signalling routeset congestion test." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 25 } cSpMtp3T16 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for routeset congestion status update." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 26 } cSpMtp3T17 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Delay to avoid oscillation of initial alignment failure and link restart." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 27 } cSpMtp3T18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer within a signalling point whose MTP restarts, for supervising link and linkset activation as well as the receipt of routing information." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 28 } cSpMtp3T19 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Supervision timer during MTP restart to avoid possible ping-pong of TFP, TFR2) and TRA messages." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 29 } cSpMtp3T20 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Overall MTP restart timer at the signalling point whose MTP restarts. Overall MTP restart timer at a signalling point adjacent to one whose MTP restarts." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 30 } cSpMtp3T21 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Overall MTP restart timer at a signalling point adjacent to one whose MTP restarts." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 31 } cSpMtp3T22 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Local inhibit test timer." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 32 } cSpMtp3T23 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Remote inhibit test timer." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 33 } cSpMtp3T24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Stabilizing timer after removal of local processor outage, used in LPO latching to RPO (national option)" REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpScalars 34 } cSpMtp3T25 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Timer at Signalling Point (SP) adjacent to restarting SP, waiting for traffic restart allowed message." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 35 } cSpMtp3T26 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Timer at restarting SP waiting to repeat traffic restart waiting message." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 36 } cSpMtp3T27 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum duration of unavailability for full restart." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 37 } cSpMtp3T28 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Timer at SP adjacent to restarting SP waiting for traffic restart waiting message." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 38 } cSpMtp3T29 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Timer started when TRA sent in response to unexpected TRA or TRW." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 39 } cSpMtp3T30 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Timer to limit sending of TFPs and TFRs in response to unexpected TRA or TRW." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 40 } cSpMtp3T31 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "False link congestion detection timer." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 41 } cSpMtp3T32 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Link oscillation timer - Procedure A." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 42 } cSpMtp3T33 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Probation timer for link oscillation - Procedure B." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 43 } cSpMtp3T34 OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Suspension timer for link oscillation - Procedure B." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)" ::= { cSpScalars 44 } -- ************************************************************* -- * * -- * SP - Linkset Table * -- * * -- ************************************************************* cSpLinksetTable OBJECT-TYPE SYNTAX SEQUENCE OF CSpLinksetTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of linksets for this SP. " ::= { cSpLinkset 1 } cSpLinksetTableEntry OBJECT-TYPE SYNTAX CSpLinksetTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of SP linkset attributes for a particular SP entity." INDEX { cSpLinksetName } ::= { cSpLinksetTable 1 } CSpLinksetTableEntry ::= SEQUENCE { cSpLinksetName CSpLinksetId, cSpLinksetAdjacentPointCode CSpPointCode, cSpLinksetState CSpOsiState, cSpLinksetInboundAcl CSpAclId, cSpLinksetOutboundAcl CSpAclId, cSpLinksetSnmmRouteTableName CSpRouteTableName, cSpLinksetSntmRouteTableName CSpRouteTableName, cSpLinksetSpare2RouteTableName CSpRouteTableName, cSpLinksetSccpRouteTableName CSpRouteTableName, cSpLinksetTupRouteTableName CSpRouteTableName, cSpLinksetIsupRouteTableName CSpRouteTableName, cSpLinksetDupcRouteTableName CSpRouteTableName, cSpLinksetDupfRouteTableName CSpRouteTableName, cSpLinksetMtupRouteTableName CSpRouteTableName, cSpLinksetBisupRouteTableName CSpRouteTableName, cSpLinksetSisupRouteTableName CSpRouteTableName, cSpLinksetSpare11RouteTableName CSpRouteTableName, cSpLinksetSpare12RouteTableName CSpRouteTableName, cSpLinksetSpare13RouteTableName CSpRouteTableName, cSpLinksetSpare14RouteTableName CSpRouteTableName, cSpLinksetSpare15RouteTableName CSpRouteTableName, cSpLinksetAccountingEnabled TruthValue, cSpLinksetNumLinks Unsigned32, cSpLinksetPacketsSent Counter32, -- Q752/3.3 cSpLinksetHCPacketsSent Counter64, -- Q752/3.3 cSpLinksetPacketsRcvd Counter32, -- Q752/3.5 cSpLinksetHCPacketsRcvd Counter64, -- Q752/3.5 cSpLinksetBytesSent Counter32, -- Q752/3.1 cSpLinksetHCBytesSent Counter64, -- Q752/3.1 cSpLinksetBytesRcvd Counter32, -- Q752/3.4 cSpLinksetHCBytesRcvd Counter64, -- Q752/3.4 cSpLinksetDurationInService TimeTicks, cSpLinksetDurationOutService TimeTicks, -- Q752/4.2 cSpLinksetMtp2T01 Unsigned32, cSpLinksetMtp2T02 Unsigned32, cSpLinksetMtp2T03 Unsigned32, cSpLinksetMtp2T4N Unsigned32, cSpLinksetMtp2T4E Unsigned32, cSpLinksetMtp2T05 Unsigned32, cSpLinksetMtp2T06 Unsigned32, cSpLinksetMtp2T07 Unsigned32, cSpLinksetMtp2T08 Unsigned32, cSpLinksetMtp3T01 Unsigned32, cSpLinksetMtp3T02 Unsigned32, cSpLinksetMtp3T03 Unsigned32, cSpLinksetMtp3T04 Unsigned32, cSpLinksetMtp3T05 Unsigned32, cSpLinksetMtp3T06 Unsigned32, cSpLinksetMtp3T07 Unsigned32, cSpLinksetMtp3T08 Unsigned32, cSpLinksetMtp3T10 Unsigned32, cSpLinksetMtp3T11 Unsigned32, cSpLinksetMtp3T12 Unsigned32, cSpLinksetMtp3T13 Unsigned32, cSpLinksetMtp3T14 Unsigned32, cSpLinksetMtp3T15 Unsigned32, cSpLinksetMtp3T16 Unsigned32, cSpLinksetMtp3T17 Unsigned32, cSpLinksetMtp3T18 Unsigned32, cSpLinksetMtp3T19 Unsigned32, cSpLinksetMtp3T20 Unsigned32, cSpLinksetMtp3T21 Unsigned32, cSpLinksetMtp3T22 Unsigned32, cSpLinksetMtp3T23 Unsigned32, cSpLinksetMtp3T24 Unsigned32, cSpLinksetMtp3T25 Unsigned32, cSpLinksetMtp3T26 Unsigned32, cSpLinksetMtp3T27 Unsigned32, cSpLinksetMtp3T28 Unsigned32, cSpLinksetMtp3T29 Unsigned32, cSpLinksetMtp3T30 Unsigned32, cSpLinksetMtp3T31 Unsigned32, cSpLinksetMtp3T32 Unsigned32, cSpLinksetMtp3T33 Unsigned32, cSpLinksetMtp3T34 Unsigned32 } cSpLinksetName OBJECT-TYPE SYNTAX CSpLinksetId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the linkset." ::= { cSpLinksetTableEntry 1 } cSpLinksetAdjacentPointCode OBJECT-TYPE SYNTAX CSpPointCode MAX-ACCESS read-only STATUS current DESCRIPTION "The point code to which this linkset is connected." ::= { cSpLinksetTableEntry 2 } cSpLinksetState OBJECT-TYPE SYNTAX CSpOsiState MAX-ACCESS read-only STATUS current DESCRIPTION "The status of this linkset." ::= { cSpLinksetTableEntry 3 } cSpLinksetInboundAcl OBJECT-TYPE SYNTAX CSpAclId MAX-ACCESS read-only STATUS current DESCRIPTION "Packets are filtered against this access control list before they are passed to the routing function. A value of zero indicates that no access control list is present." ::= { cSpLinksetTableEntry 4 } cSpLinksetOutboundAcl OBJECT-TYPE SYNTAX CSpAclId MAX-ACCESS read-only STATUS current DESCRIPTION "Packets are filtered against this access control list after they have passed through the routing function. A value of zero indicates that no access control list is present." ::= { cSpLinksetTableEntry 5 } cSpLinksetSnmmRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for signalling network management messages." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 6 } cSpLinksetSntmRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for signalling network test and maintenance messages." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 7 } cSpLinksetSpare2RouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "This routing table has been defined as a spare routing table by the standards committee." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 8 } cSpLinksetSccpRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for SS7 Signaling Connection Control Part(SCCP) messages." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 9 } cSpLinksetTupRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for Telephone User Part(TUP) messages." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 10 } cSpLinksetIsupRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for ISDN User Part messages." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 11 } cSpLinksetDupcRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for Data User Part (call and circuit-related messages)." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 12 } cSpLinksetDupfRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for Data User Part (facility registration and cancellation messages)." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 13 } cSpLinksetMtupRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for MTP Testing User Part messages." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 14 } cSpLinksetBisupRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for Broadband ISDN User Part(BISUP) messages." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 15 } cSpLinksetSisupRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "The routing table for Satellite ISDN User Part(SISUP) messages." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 16 } cSpLinksetSpare11RouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "This routing table has been defined as a spare routing table by the standards committee." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 17 } cSpLinksetSpare12RouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "This routing table has been defined as a spare routing table by the standards committee." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 18 } cSpLinksetSpare13RouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "This routing table has been defined as a spare routing table by the standards committee." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 19 } cSpLinksetSpare14RouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "This routing table has been defined as a spare routing table by the standards committee." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 20 } cSpLinksetSpare15RouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS read-only STATUS current DESCRIPTION "This routing table has been defined as a spare routing table by the standards committee." REFERENCE "ITU Q.704 Signalling network functions and messages, section 14.2.1." ::= { cSpLinksetTableEntry 21 } cSpLinksetAccountingEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates if accounting for this linkset is enabled. 'true' Indicates that the accounting function is enabled for this linkset and is being accumulated in cSpAccountingTable. 'false' Indicates that the accounting function is disabled." DEFVAL { false } ::= { cSpLinksetTableEntry 22 } cSpLinksetNumLinks OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of links in this linkset." ::= { cSpLinksetTableEntry 23 } cSpLinksetPacketsSent OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets(message signal units) transmitted by this linkset(Q752/3.3)." ::= { cSpLinksetTableEntry 24 } cSpLinksetHCPacketsSent OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets(message signal units) transmitted by this linkset(Q752/3.3). This is the 64-bit version of cSpLinksetPacketsSent." ::= { cSpLinksetTableEntry 25 } cSpLinksetPacketsRcvd OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets(message signal units) received by this linkset(Q752/3.5)." ::= { cSpLinksetTableEntry 26 } cSpLinksetHCPacketsRcvd OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets(message signal units) received by this linkset(Q752/3.5). This is the 64-bit version of cSpLinksetPacketsRcvd." ::= { cSpLinksetTableEntry 27 } cSpLinksetBytesSent OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes transmitted by this linkset(Q752/3.1)." ::= { cSpLinksetTableEntry 28 } cSpLinksetHCBytesSent OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes transmitted by this linkset(Q752/3.1). This is the 64-bit version of cSpLinksetBytesSent." ::= { cSpLinksetTableEntry 29 } cSpLinksetBytesRcvd OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes received by this linkset(Q752/3.4)." ::= { cSpLinksetTableEntry 30 } cSpLinksetHCBytesRcvd OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bytes received by this linkset(Q752/3.4). This is the 64-bit version of cSpLinksetBytesRcvd." ::= { cSpLinksetTableEntry 31 } cSpLinksetDurationInService OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time linkset was providing service related to Q752/Table 4.2." ::= { cSpLinksetTableEntry 32 } cSpLinksetDurationOutService OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time linkset was Out-of-Service as required for Q752/Table 4.2." ::= { cSpLinksetTableEntry 33 } cSpLinksetMtp2T01 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Alignment ready timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 34 } cSpLinksetMtp2T02 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Not aligned timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 35 } cSpLinksetMtp2T03 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Aligned timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 36 } cSpLinksetMtp2T4N OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Proving period timer normal timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 37 } cSpLinksetMtp2T4E OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Proving period timer emergency timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 38 } cSpLinksetMtp2T05 OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Sending SIB timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 39 } cSpLinksetMtp2T06 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Remote congestion timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 40 } cSpLinksetMtp2T07 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Excessive delay of acknowledgement timer. The default and valid range is dependant on the value of cSpSs7Variant The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 41 } cSpLinksetMtp2T08 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Interval timer for error interval monitor. Note that this timer is only applicable if cSpLinkType is serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 42 } cSpLinksetMtp3T01 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Delay to avoid message mis-sequencing on changeover." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 43 } cSpLinksetMtp3T02 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for changeover acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 44 } cSpLinksetMtp3T03 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Time controlled diversion-delay to avoid mis-sequencing on change back." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 45 } cSpLinksetMtp3T04 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for change back acknowledgement (first attempt)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 46 } cSpLinksetMtp3T05 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for change back acknowledgement (second attempt)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 47 } cSpLinksetMtp3T06 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Delay to avoid message mis-sequencing on controlled rerouting." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 48 } cSpLinksetMtp3T07 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for signalling data link connection acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 49 } cSpLinksetMtp3T08 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Transfer prohibited inhibition timer (transient solution)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 50 } cSpLinksetMtp3T10 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting to repeat signalling routeset test message." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 51 } cSpLinksetMtp3T11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Transfer restricted timer. (This is one way of implementing the function described in 13.4/Q.704 and mainly intended to simplify SPs.)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 52 } cSpLinksetMtp3T12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for uninhibit acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 53 } cSpLinksetMtp3T13 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for force uninhibit." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 54 } cSpLinksetMtp3T14 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for inhibition acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 55 } cSpLinksetMtp3T15 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting to start signalling routeset congestion test." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 56 } cSpLinksetMtp3T16 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for routeset congestion status update." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 57 } cSpLinksetMtp3T17 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Delay to avoid oscillation of initial alignment failure and link restart." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 58 } cSpLinksetMtp3T18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer within a signalling point whose MTP restarts, for supervising link and linkset activation as well as the receipt of routing information." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 59 } cSpLinksetMtp3T19 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Supervision timer during MTP restart to avoid possible ping-pong of TFP, TFR2) and TRA messages." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 60 } cSpLinksetMtp3T20 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Overall MTP restart timer at the signalling point whose MTP restarts. Overall MTP restart timer at a signalling point adjacent to one whose MTP restarts." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 61 } cSpLinksetMtp3T21 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Overall MTP restart timer at a signalling point adjacent to one whose MTP restarts." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 62 } cSpLinksetMtp3T22 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Local inhibit test timer." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 63 } cSpLinksetMtp3T23 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Remote inhibit test timer." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 64 } cSpLinksetMtp3T24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Stabilizing timer after removal of local processor outage, used in LPO latching to RPO (national option)" REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 65 } cSpLinksetMtp3T25 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer at Signalling Point (SP) adjacent to restarting SP, waiting for traffic restart allowed message." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 66 } cSpLinksetMtp3T26 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer at restarting SP waiting to repeat traffic restart waiting message." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 67 } cSpLinksetMtp3T27 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum duration of unavailability for full restart." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 68 } cSpLinksetMtp3T28 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer at SP adjacent to restarting SP waiting for traffic restart waiting message." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 69 } cSpLinksetMtp3T29 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer started when TRA sent in response to unexpected TRA or TRW." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 70 } cSpLinksetMtp3T30 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer to limit sending of TFPs and TFRs in response to unexpected TRA or TRW." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 71 } cSpLinksetMtp3T31 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "False link congestion detection timer." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 72 } cSpLinksetMtp3T32 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Link oscillation timer - Procedure A." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 73 } cSpLinksetMtp3T33 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Probation timer for link oscillation - Procedure B." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 74 } cSpLinksetMtp3T34 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Suspension timer for link oscillation - Procedure B." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinksetTableEntry 75 } -- ************************************************************* -- * * -- * SP - Link Table * -- * * -- ************************************************************* cSpLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF CSpLinkTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of SP links for this SP." ::= { cSpLink 1 } cSpLinkTableEntry OBJECT-TYPE SYNTAX CSpLinkTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of SP link attributes." INDEX { cSpLinksetName, -- shared index cSpLinkSlc } ::= { cSpLinkTable 1 } CSpLinkTableEntry ::= SEQUENCE { cSpLinkSlc CSpLinkSLC, cSpLinkState CSpOsiState, cSpLinkType CSpLinkType, cSpLinkifIndex InterfaceIndexOrZero, cSpLinkSctpAssociation Integer32, cSpLinkMtp3PacketsRcvd Counter32, cSpLinkMtp3PacketsSent Counter32, cSpLinkHCMtp3PacketsRcvd Counter64, cSpLinkHCMtp3PacketsSent Counter64, cSpLinkMtp3BytesRcvd Counter32, cSpLinkMtp3BytesSent Counter32, cSpLinkHCMtp3BytesRcvd Counter64, cSpLinkHCMtp3BytesSent Counter64, cSpLinkMtp2T01 Unsigned32, cSpLinkMtp2T02 Unsigned32, cSpLinkMtp2T03 Unsigned32, cSpLinkMtp2T4N Unsigned32, cSpLinkMtp2T4E Unsigned32, cSpLinkMtp2T05 Unsigned32, cSpLinkMtp2T06 Unsigned32, cSpLinkMtp2T07 Unsigned32, cSpLinkMtp2T08 Unsigned32, cSpLinkMtp3T01 Unsigned32, cSpLinkMtp3T02 Unsigned32, cSpLinkMtp3T03 Unsigned32, cSpLinkMtp3T04 Unsigned32, cSpLinkMtp3T05 Unsigned32, cSpLinkMtp3T06 Unsigned32, cSpLinkMtp3T07 Unsigned32, cSpLinkMtp3T08 Unsigned32, cSpLinkMtp3T10 Unsigned32, cSpLinkMtp3T11 Unsigned32, cSpLinkMtp3T12 Unsigned32, cSpLinkMtp3T13 Unsigned32, cSpLinkMtp3T14 Unsigned32, cSpLinkMtp3T15 Unsigned32, cSpLinkMtp3T16 Unsigned32, cSpLinkMtp3T17 Unsigned32, cSpLinkMtp3T18 Unsigned32, cSpLinkMtp3T19 Unsigned32, cSpLinkMtp3T20 Unsigned32, cSpLinkMtp3T21 Unsigned32, cSpLinkMtp3T22 Unsigned32, cSpLinkMtp3T23 Unsigned32, cSpLinkMtp3T24 Unsigned32, cSpLinkMtp3T25 Unsigned32, cSpLinkMtp3T26 Unsigned32, cSpLinkMtp3T27 Unsigned32, cSpLinkMtp3T28 Unsigned32, cSpLinkMtp3T29 Unsigned32, cSpLinkMtp3T30 Unsigned32, cSpLinkMtp3T31 Unsigned32, cSpLinkMtp3T32 Unsigned32, cSpLinkMtp3T33 Unsigned32, cSpLinkMtp3T34 Unsigned32, cSpLinkXmitQueueDepth Gauge32, cSpLinkXmitQueueDepthHigh Unsigned32, cSpLinkXmitQueueDepthHighReset TimeStamp, cSpLinkCongestionState Unsigned32, cSpLinkCongestionAbate1 Unsigned32, cSpLinkCongestionAbate2 Unsigned32, cSpLinkCongestionAbate3 Unsigned32, cSpLinkCongestionOnset1 Unsigned32, cSpLinkCongestionOnset2 Unsigned32, cSpLinkCongestionOnset3 Unsigned32, cSpLinkSigLinkTest TruthValue, cSpLinkQ752T1E1 TimeTicks, cSpLinkQ752T1E2 Counter32, cSpLinkQ752T1E3 Counter32, cSpLinkQ752T1E4 Counter32, cSpLinkQ752T1E5 Counter32, cSpLinkQ752T1E6 Counter32, cSpLinkQ752T1E7 Counter32, cSpLinkQ752T1E8 Counter32, cSpLinkQ752T1E9 Counter32, cSpLinkQ752T1E10 Counter32, cSpLinkQ752T1E11 Counter32, cSpLinkQ752T2E1 TimeTicks, cSpLinkQ752T2E5 TimeTicks, cSpLinkQ752T2E6 TimeTicks, cSpLinkQ752T2E7 TimeTicks, cSpLinkQ752T2E9 TimeTicks, cSpLinkQ752T2E10 Counter32, cSpLinkQ752T2E15 TimeTicks, cSpLinkQ752T2E16 Counter32, cSpLinkQ752T2E18 Counter32, cSpLinkMtp3PacketsRetrans Counter32, -- Q752/3.2 cSpLinkMtp3BytesRetrans Counter32, -- Q752/3.2 cSpLinkQ752T3E6 Counter32, cSpLinkQ752T3E7 TimeTicks, cSpLinkQ752T3E10L1 Counter32, cSpLinkQ752T3E10L2 Counter32, cSpLinkQ752T3E10L3 Counter32, cSpLinkQ752T3E11L1 Counter32, cSpLinkQ752T3E11L2 Counter32, cSpLinkQ752T3E11L3 Counter32 } cSpLinkSlc OBJECT-TYPE SYNTAX CSpLinkSLC MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Signalling Link Code for this link." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 1 } cSpLinkState OBJECT-TYPE SYNTAX CSpOsiState MAX-ACCESS read-only STATUS current DESCRIPTION "The status of this link." ::= { cSpLinkTableEntry 2 } cSpLinkType OBJECT-TYPE SYNTAX CSpLinkType MAX-ACCESS read-only STATUS current DESCRIPTION "The link type." REFERENCE "For SCTP see RFC 2960." ::= { cSpLinkTableEntry 3 } cSpLinkifIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "If the link type specified by cSpLinkType is serial, this is the ifIndex specified in MIB-2, otherwise no significance is to be placed on this value." REFERENCE "RFC1213.txt" ::= { cSpLinkTableEntry 4 } cSpLinkSctpAssociation OBJECT-TYPE SYNTAX Integer32(-1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "If the link type specified by cSpLinkType is sctpIp, this is the sctpAssocId defined in the CISCO-SCTP-MIB. Where value greater than or equal to zero indicates a valid association and negative one indicates an invalid association. This value will always be set to negative one when cSpLinkType is set to the two value." ::= { cSpLinkTableEntry 5 } cSpLinkMtp3PacketsRcvd OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 packets received by this link. This measurement is specified in Q752/3.5" ::= { cSpLinkTableEntry 6 } cSpLinkMtp3PacketsSent OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 packets sent by this link. This measurement is specified in Q752/3.3" ::= { cSpLinkTableEntry 7 } cSpLinkHCMtp3PacketsRcvd OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 packets received by this link. This is the 64-bit version of cSpLinkMtp3PacketsRcvd. This measurement is specified in Q752/3.5" ::= { cSpLinkTableEntry 8 } cSpLinkHCMtp3PacketsSent OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 packets sent by this link. This is the 64-bit version of cSpLinkMtp3PacketsSent. This measurement is specified in Q752/3.3" ::= { cSpLinkTableEntry 9 } cSpLinkMtp3BytesRcvd OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 bytes received by this link. This measurement is specified in Q752/3.4" ::= { cSpLinkTableEntry 10 } cSpLinkMtp3BytesSent OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 bytes sent by this link. This measurement is specified in Q752/3.1" ::= { cSpLinkTableEntry 11 } cSpLinkHCMtp3BytesRcvd OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 bytes received by this link. This is the 64-bit version of cSpLinkMtp3BytesRcvd. This measurement is specified in Q752/3.4" ::= { cSpLinkTableEntry 12 } cSpLinkHCMtp3BytesSent OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 bytes sent by this link. This is the 64-bit version of cSpLinkMtp3BytesSent. This measurement is specified in Q752/3.1" ::= { cSpLinkTableEntry 13 } cSpLinkMtp2T01 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Alignment ready timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType value is equal to 'serial'. A get on this object will return a zero if cSpLinkType is not serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 14 } cSpLinkMtp2T02 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Not aligned timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial. A get on this object will return a zero if cSpLinkType is not serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 15 } cSpLinkMtp2T03 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Aligned timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial. A get on this object will return a zero if cSpLinkType is not serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 16 } cSpLinkMtp2T4N OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Proving period timer normal timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 17 } cSpLinkMtp2T4E OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Proving period timer emergency timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial. A get on this object will return a zero if cSpLinkType is not serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 18 } cSpLinkMtp2T05 OBJECT-TYPE SYNTAX Unsigned32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Sending SIB timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial. A get on this object will return a zero if cSpLinkType is not serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 19 } cSpLinkMtp2T06 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Remote congestion timer. The default and valid range is dependant on the value of cSpSs7Variant. The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial. A get on this object will return a zero if cSpLinkType is not serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 20 } cSpLinkMtp2T07 OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 milli-seconds." MAX-ACCESS read-only STATUS current DESCRIPTION "Excessive delay of acknowledgement timer. The default and valid range is dependant on the value of cSpSs7Variant The ranges are defined in the following references. This timer is only applicable if cSpLinkType is serial. A get on this object will return a zero if cSpLinkType is not serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 21 } cSpLinkMtp2T08 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Interval timer for error interval monitor. Note that this timer is only applicable if cSpLinkType is serial. A get on this object will return a zero if cSpLinkType is not serial." REFERENCE "ITU Q.703 Signalling Link. ANSI T1.111.3 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 22 } cSpLinkMtp3T01 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Delay to avoid message mis-sequencing on changeover." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 23 } cSpLinkMtp3T02 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for changeover acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 24 } cSpLinkMtp3T03 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Time controlled diversion-delay to avoid mis-sequencing on change back." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 25 } cSpLinkMtp3T04 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for change back acknowledgement (first attempt)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 26 } cSpLinkMtp3T05 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for change back acknowledgement (second attempt)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 27 } cSpLinkMtp3T06 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Delay to avoid message mis-sequencing on controlled rerouting." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 28 } cSpLinkMtp3T07 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for signalling data link connection acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 29 } cSpLinkMtp3T08 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Transfer prohibited inhibition timer (transient solution)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 30 } cSpLinkMtp3T10 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting to repeat signalling routeset test message." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 31 } cSpLinkMtp3T11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Transfer restricted timer. (This is one way of implementing the function described in 13.4/Q.704 and mainly intended to simplify SPs.)." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 32 } cSpLinkMtp3T12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for uninhibit acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 33 } cSpLinkMtp3T13 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for force uninhibit." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 34 } cSpLinkMtp3T14 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for inhibition acknowledgement." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 35 } cSpLinkMtp3T15 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting to start signalling routeset congestion test." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 36 } cSpLinkMtp3T16 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Waiting for routeset congestion status update." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 37 } cSpLinkMtp3T17 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Delay to avoid oscillation of initial alignment failure and link restart." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 38 } cSpLinkMtp3T18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer within a signalling point whose MTP restarts, for supervising link and linkset activation as well as the receipt of routing information." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 39 } cSpLinkMtp3T19 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Supervision timer during MTP restart to avoid possible ping-pong of TFP, TFR2) and TRA messages." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 40 } cSpLinkMtp3T20 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Overall MTP restart timer at the signalling point whose MTP restarts. Overall MTP restart timer at a signalling point adjacent to one whose MTP restarts." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 41 } cSpLinkMtp3T21 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Overall MTP restart timer at a signalling point adjacent to one whose MTP restarts." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 42 } cSpLinkMtp3T22 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Local inhibit test timer." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 43 } cSpLinkMtp3T23 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Remote inhibit test timer." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 44 } cSpLinkMtp3T24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Stabilizing timer after removal of local processor outage, used in LPO latching to RPO (national option)" REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 45 } cSpLinkMtp3T25 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer at Signalling Point (SP) adjacent to restarting SP, waiting for traffic restart allowed message." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 46 } cSpLinkMtp3T26 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer at restarting SP waiting to repeat traffic restart waiting message." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 47 } cSpLinkMtp3T27 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum duration of unavailability for full restart." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 48 } cSpLinkMtp3T28 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer at SP adjacent to restarting SP waiting for traffic restart waiting message." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 49 } cSpLinkMtp3T29 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer started when TRA sent in response to unexpected TRA or TRW." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 50 } cSpLinkMtp3T30 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer to limit sending of TFPs and TFRs in response to unexpected TRA or TRW." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 51 } cSpLinkMtp3T31 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "False link congestion detection timer." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 52 } cSpLinkMtp3T32 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Link oscillation timer - Procedure A." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 53 } cSpLinkMtp3T33 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Probation timer for link oscillation - Procedure B." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 54 } cSpLinkMtp3T34 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Suspension timer for link oscillation - Procedure B." REFERENCE "ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Message Transfer Part (MTP)." ::= { cSpLinkTableEntry 55 } cSpLinkXmitQueueDepth OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets waiting to be sent over this link." ::= { cSpLinkTableEntry 56 } cSpLinkXmitQueueDepthHigh OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This is the maximum number of packets waiting to be sent over this link since the last time this value was reset as indicated by cSpLinkXmitQueueDepthHighReset. Resetting this object is achieved by setting this object to 0. Attempting to set this object to any other value will result in a wrongValue error." ::= { cSpLinkTableEntry 57 } cSpLinkXmitQueueDepthHighReset OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates when cSpLinkXmitQueueDepthHigh was set to 0." ::= { cSpLinkTableEntry 58 } cSpLinkCongestionState OBJECT-TYPE SYNTAX Unsigned32 (0..3) MAX-ACCESS read-only STATUS current DESCRIPTION "The signalling link congestion status of this link. 0 is the least congestion level, 3 is the highest congestion level." REFERENCE "ITU Q.704 Signalling network functions and messages. ANSI T1.111 Telecommunications - Signaling system No. 7 (SS7)-Signalling network functions and messages 2.3.5.2." ::= { cSpLinkTableEntry 59 } cSpLinkCongestionAbate1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Threshold used to abate congestion level 1." ::= { cSpLinkTableEntry 60 } cSpLinkCongestionAbate2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Threshold used to abate congestion level 2." ::= { cSpLinkTableEntry 61 } cSpLinkCongestionAbate3 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Threshold used to abate congestion level 3." ::= { cSpLinkTableEntry 62 } cSpLinkCongestionOnset1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Threshold used to mark onset of congestion level 1." ::= { cSpLinkTableEntry 63 } cSpLinkCongestionOnset2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Threshold used to mark onset of congestion level 2." ::= { cSpLinkTableEntry 64 } cSpLinkCongestionOnset3 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Threshold used to mark onset of congestion level 3." ::= { cSpLinkTableEntry 65 } cSpLinkSigLinkTest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicated if signalling link test is enabled on this link. true : signalling link test is enabled. false : signalling link test not enabled." DEFVAL { true } ::= { cSpLinkTableEntry 66 } cSpLinkQ752T1E1 OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Duration of link in the In-Service state Q752/1.1." ::= { cSpLinkTableEntry 67 } cSpLinkQ752T1E2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Link failures - All reasons Q752/1.2." ::= { cSpLinkTableEntry 68 } cSpLinkQ752T1E3 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Link failures - Abnormal FIBR/BSNR Q752/1.4." ::= { cSpLinkTableEntry 69 } cSpLinkQ752T1E4 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Link failures - Excessive delay of acknowledgement Q752/1.4." ::= { cSpLinkTableEntry 70 } cSpLinkQ752T1E5 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Link failures - Excessive error rate Q752/1.5." ::= { cSpLinkTableEntry 71 } cSpLinkQ752T1E6 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Link failures - Excessive duration of congestion Q752/1.6." ::= { cSpLinkTableEntry 72 } cSpLinkQ752T1E7 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of alignment or proving errors Q752/1.7." ::= { cSpLinkTableEntry 73 } cSpLinkQ752T1E8 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of signal units received in error Q752/1.8." ::= { cSpLinkTableEntry 74 } cSpLinkQ752T1E9 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of negative acknowledgements received Q752/1.9." ::= { cSpLinkTableEntry 75 } cSpLinkQ752T1E10 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of 'local automatic changeover' events Q752/1.10." ::= { cSpLinkTableEntry 76 } cSpLinkQ752T1E11 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of 'local automatic changeback' events Q752/1.11." ::= { cSpLinkTableEntry 77 } -- Q752.12 Signalling Link Restoration The standard only requires -- that an event be issued when this occurs. cSpLinkQ752T2E1 OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Duration of Signalling Link unavailable(for any reason) Q752/2.1." ::= { cSpLinkTableEntry 78 } -- Q752/2.2 - Q752/2.4 deleted cSpLinkQ752T2E5 OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Duration of Signalling Link unavailable due to local management actions Q752/2.5." ::= { cSpLinkTableEntry 79 } cSpLinkQ752T2E6 OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Duration of Signalling Link unavailable due to remote management actions Q752/2.6." ::= { cSpLinkTableEntry 80 } cSpLinkQ752T2E7 OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Duration of Signalling Link unavailable due to link failure Q752/2.7." ::= { cSpLinkTableEntry 81 } -- Q752/2.8 deleted cSpLinkQ752T2E9 OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Duration of Signalling Link unavailable due to remote processor outage Q752/2.9." ::= { cSpLinkTableEntry 82 } cSpLinkQ752T2E10 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of 'remote processor outage' events Q752/2.10 and Q752/2.11. The standard only requires that events are issued. The entries have been combined into a single entry to track all occurrences of these event types." ::= { cSpLinkTableEntry 83 } -- Q752/2.12 Deleted -- Q752/2.13 and Q752/2.14. These values can be calculated from -- information provided by Q752/2.15, Q752/2.16, Q752/2.17 -- and Q752/2.18 cSpLinkQ752T2E15 OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Duration of local busy Q752/2.15." ::= { cSpLinkTableEntry 84 } cSpLinkQ752T2E16 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of local inhibition Q752/2.16 and Q752/2.17. The standard only requires that events are issued. The entries have been combined into a single entry to track all occurrences of these event types." ::= { cSpLinkTableEntry 85 } cSpLinkQ752T2E18 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of remote inhibition Q752/2.18 and Q752/2.19. The standard only requires that events are issued. The entries have been combined into a single entry to track all occurrences of these event types." ::= { cSpLinkTableEntry 86 } cSpLinkMtp3PacketsRetrans OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 packets retransmitted on this link. This measurement is specified in Q752/3.2" ::= { cSpLinkTableEntry 87 } cSpLinkMtp3BytesRetrans OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MTP3 bytes retransmitted on this link. This measurement is specified in Q752/3.2" ::= { cSpLinkTableEntry 88 } cSpLinkQ752T3E6 OBJECT-TYPE SYNTAX Counter32 UNITS "events" MAX-ACCESS read-only STATUS current DESCRIPTION "The number times this signalling link was marked congested. This measurement is specified in Q752/3.6" ::= { cSpLinkTableEntry 89 } cSpLinkQ752T3E7 OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Cumulative duration of signalling link congestion Q752/3.7." ::= { cSpLinkTableEntry 90 } cSpLinkQ752T3E10L1 OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets(MSUs) discarded due to signalling link level 1 congestion Q752/3.10" ::= { cSpLinkTableEntry 91 } cSpLinkQ752T3E10L2 OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets(MSUs) discard due to signalling link level 2 congestion Q752/3.10" ::= { cSpLinkTableEntry 92 } cSpLinkQ752T3E10L3 OBJECT-TYPE SYNTAX Counter32 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets(MSUs) discard due to signalling link level 3 congestion Q752/3.10" ::= { cSpLinkTableEntry 93 } cSpLinkQ752T3E11L1 OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number times this signalling link entered congestion level 1 and packets were discarded. This measurement is specified in Q752/3.11" ::= { cSpLinkTableEntry 94 } cSpLinkQ752T3E11L2 OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number times this signalling link entered congestion level 2 and packets were discarded. This measurement is specified in Q752/3.11" ::= { cSpLinkTableEntry 95 } cSpLinkQ752T3E11L3 OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number times this signalling link entered congestion level 3 and packets were discarded. This measurement is specified in Q752/3.11" ::= { cSpLinkTableEntry 96 } -- ************************************************************* -- * * -- * SP - Route Table * -- * * -- ************************************************************* cSpRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF CSpRouteTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The route table for determining the linkset that a packet must traverse to arrive at its destination node given by the destination point code." ::= { cSpRoute 1 } cSpRouteTableEntry OBJECT-TYPE SYNTAX CSpRouteTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list statements used to route mtp3 packets. Information in packets are matched against the information in each route statements and the packet is sent on the selected linkset." INDEX { cSpRouteTableName, cSpRouteDpc, cSpRouteDestLsCost, cSpRouteDestLinkset, cSpRouteMask } ::= { cSpRouteTable 1 } CSpRouteTableEntry ::= SEQUENCE { cSpRouteTableName CSpRouteTableName, cSpRouteDpc CSpPointCode, cSpRouteDestLsCost Unsigned32, cSpRouteDestLinkset CSpLinksetId, cSpRouteMask Unsigned32, cSpRouteStatus CSpRouteStatus } cSpRouteTableName OBJECT-TYPE SYNTAX CSpRouteTableName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configured name for this route table." ::= { cSpRouteTableEntry 1 } cSpRouteDpc OBJECT-TYPE SYNTAX CSpPointCode MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination point code." ::= { cSpRouteTableEntry 2 } cSpRouteDestLsCost OBJECT-TYPE SYNTAX Unsigned32 (1..9) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The cost assigned to this linkset matching this route. Higher numbers represent higher cost." ::= { cSpRouteTableEntry 3 } cSpRouteDestLinkset OBJECT-TYPE SYNTAX CSpLinksetId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The linkset that the packet is to be forwarded to on matching this route." ::= { cSpRouteTableEntry 4 } cSpRouteMask OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mask used to define which part of cSpRouteDpc is significant when comparing the cSpRouteDpc to the destination code point in the packet to be routed." ::= { cSpRouteTableEntry 5 } cSpRouteStatus OBJECT-TYPE SYNTAX CSpRouteStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the route from the perspective of the Signaling Point." ::= { cSpRouteTableEntry 6 } -- ************************************************************* -- * * -- * SP - Access Control List Table * -- * * -- ************************************************************* cSpAclTable OBJECT-TYPE SYNTAX SEQUENCE OF CSpAclTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of SP access controls. The access control definition controls which packets are accepted or rejected. The access control may be applied before sending the packet to the routing table or may be applied after the packet is processed by the routing table." ::= { cSpAccessControlList 1 } cSpAclTableEntry OBJECT-TYPE SYNTAX CSpAclTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of SP access control attributes." INDEX { cSpAclId, cSpAclEntryNumber } ::= { cSpAclTable 1 } CSpAclTableEntry ::= SEQUENCE { cSpAclId CSpAclId, cSpAclEntryNumber Unsigned32, cSpAclType INTEGER, cSpAclDpc CSpPointCode, cSpAclDpcMask Unsigned32, cSpAclOpc CSpPointCode, cSpAclOpcMask Unsigned32, cSpAclSi CSpAclSi, cSpAclPattern DisplayString, cSpAclOffset Unsigned32, cSpAclAction CSpAclAction } cSpAclId OBJECT-TYPE SYNTAX CSpAclId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identifier for this ACL." ::= { cSpAclTableEntry 1 } cSpAclEntryNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An numeric value assigned to each access list entry. The values start with zero and increase by one." ::= { cSpAclTableEntry 2 } cSpAclType OBJECT-TYPE SYNTAX INTEGER { dpc(1), opc(2), pattern(3), sio(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates which columns are used in determining the matching criteria for this access control. 'dpc' : cSpAclDpc and cSpAclDpcMask are the relevant columns. The packet is compared to cSpAclDpc in conjunction with cSpAclDpcMask to determine if the packet matches this access control. 'opc' : cSpAclOpc and cSpAclOpcMask are the relevant columns. The packet is compared to cSpAclOpc in conjunction with cSpAclOpcMask to determine if the packet matches this access control. 'pattern' : cSpAclPattern and cSpAclOffset are the relevant columns. The matching criteria is based on matching the pattern specified by cSpAclPattern at offset cSpAclOffset from the start of the packet. 'sio' : cSpAclSi is the relevant column. The SIO field of the packet is compared to cSpAclSi and a match is based on equality. " ::= { cSpAclTableEntry 3 } cSpAclDpc OBJECT-TYPE SYNTAX CSpPointCode MAX-ACCESS read-only STATUS current DESCRIPTION "The destination point code specified for this ACL." ::= { cSpAclTableEntry 4 } cSpAclDpcMask OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The mask used to define which part of the point code in the packet is significant when comparing the destination point code with cSpAclDpc." ::= { cSpAclTableEntry 5 } cSpAclOpc OBJECT-TYPE SYNTAX CSpPointCode MAX-ACCESS read-only STATUS current DESCRIPTION "The origin point code specified in this ACL." ::= { cSpAclTableEntry 6 } cSpAclOpcMask OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The mask used to define which part of the origin point code in the packet is significant when comparing the origin point code with cSpAclDpc." ::= { cSpAclTableEntry 7 } cSpAclSi OBJECT-TYPE SYNTAX CSpAclSi MAX-ACCESS read-only STATUS current DESCRIPTION "The Service Indicator Octet." ::= { cSpAclTableEntry 8 } cSpAclPattern OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32) ) MAX-ACCESS read-only STATUS current DESCRIPTION "The pattern used to match a packet at offset cSpAclOffset." DEFVAL { "" } ::= { cSpAclTableEntry 9 } cSpAclOffset OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The offset into the packet were we begin matching the pattern specified by cSpAclPattern is to start." ::= { cSpAclTableEntry 10 } cSpAclAction OBJECT-TYPE SYNTAX CSpAclAction MAX-ACCESS read-only STATUS current DESCRIPTION "The action to be performed on the packet that matched this access control." ::= { cSpAclTableEntry 11 } -- ************************************************************* -- * * -- * SP - Accounting Table * -- * * -- * This table supports Q752/6.6 and Q752/6.7 * -- ************************************************************* cSpAccountingTable OBJECT-TYPE SYNTAX SEQUENCE OF CSpAccountingTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of packet and byte counts for packets that match an ACL in the linkset's inbound ACL and in the outbound ACL. These counters are updated no more frequently than the value specified by cSpAccCheckPointPeriod. Polling more frequently than this period results in the same values being returned." ::= { cSpAccounting 1 } cSpAccountingTableEntry OBJECT-TYPE SYNTAX CSpAccountingTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of accounting objects." INDEX { cSpAccTableId, cSpLinksetName, -- shared index cSpAccDpc, cSpAccOpc } ::= { cSpAccountingTable 1 } CSpAccountingTableEntry ::= SEQUENCE { cSpAccTableId INTEGER, cSpAccDpc CSpPointCode, cSpAccOpc CSpPointCode, cSpAccRcvdPackets Counter32, cSpAccHCRcvdPackets Counter64, cSpAccSentPackets Counter32, cSpAccHCSentPackets Counter64, cSpAccRcvdBytes Counter32, cSpAccHCRcvdBytes Counter64, cSpAccSentBytes Counter32, cSpAccHCSentBytes Counter64, cSpAccSnmmRcvdPackets Counter32, cSpAccHCSnmmRcvdPackets Counter64, cSpAccSnmmRcvdBytes Counter32, cSpAccHCSnmmRcvdBytes Counter64, cSpAccSnmmSentPackets Counter32, cSpAccHCSnmmSentPackets Counter64, cSpAccSnmmSentBytes Counter32, cSpAccHCSnmmSentBytes Counter64, cSpAccSntmRcvdPackets Counter32, cSpAccHCSntmRcvdPackets Counter64, cSpAccSntmRcvdBytes Counter32, cSpAccHCSntmRcvdBytes Counter64, cSpAccSntmSentPackets Counter32, cSpAccHCSntmSentPackets Counter64, cSpAccSntmSentBytes Counter32, cSpAccHCSntmSentBytes Counter64, cSpAccSpare2RcvdPackets Counter32, cSpAccHCSpare2RcvdPackets Counter64, cSpAccSpare2RcvdBytes Counter32, cSpAccHCSpare2RcvdBytes Counter64, cSpAccSpare2SentPackets Counter32, cSpAccHCSpare2SentPackets Counter64, cSpAccSpare2SentBytes Counter32, cSpAccHCSpare2SentBytes Counter64, cSpAccSccpRcvdPackets Counter32, cSpAccHCSccpRcvdPackets Counter64, cSpAccSccpRcvdBytes Counter32, cSpAccHCSccpRcvdBytes Counter64, cSpAccSccpSentPackets Counter32, cSpAccHCSccpSentPackets Counter64, cSpAccSccpSentBytes Counter32, cSpAccHCSccpSentBytes Counter64, cSpAccTupRcvdPackets Counter32, cSpAccHCTupRcvdPackets Counter64, cSpAccTupRcvdBytes Counter32, cSpAccHCTupRcvdBytes Counter64, cSpAccTupSentPackets Counter32, cSpAccHCTupSentPackets Counter64, cSpAccTupSentBytes Counter32, cSpAccHCTupSentBytes Counter64, cSpAccIsupRcvdPackets Counter32, cSpAccHCIsupRcvdPackets Counter64, cSpAccIsupRcvdBytes Counter32, cSpAccHCIsupRcvdBytes Counter64, cSpAccIsupSentPackets Counter32, cSpAccHCIsupSentPackets Counter64, cSpAccIsupSentBytes Counter32, cSpAccHCIsupSentBytes Counter64, cSpAccDupcRcvdPackets Counter32, cSpAccHCDupcRcvdPackets Counter64, cSpAccDupcRcvdBytes Counter32, cSpAccHCDupcRcvdBytes Counter64, cSpAccDupcSentPackets Counter32, cSpAccHCDupcSentPackets Counter64, cSpAccDupcSentBytes Counter32, cSpAccHCDupcSentBytes Counter64, cSpAccDupfRcvdPackets Counter32, cSpAccHCDupfRcvdPackets Counter64, cSpAccDupfRcvdBytes Counter32, cSpAccHCDupfRcvdBytes Counter64, cSpAccDupfSentPackets Counter32, cSpAccHCDupfSentPackets Counter64, cSpAccDupfSentBytes Counter32, cSpAccHCDupfSentBytes Counter64, cSpAccMtupRcvdPackets Counter32, cSpAccHCMtupRcvdPackets Counter64, cSpAccMtupRcvdBytes Counter32, cSpAccHCMtupRcvdBytes Counter64, cSpAccMtupSentPackets Counter32, cSpAccHCMtupSentPackets Counter64, cSpAccMtupSentBytes Counter32, cSpAccHCMtupSentBytes Counter64, cSpAccBisupRcvdPackets Counter32, cSpAccHCBisupRcvdPackets Counter64, cSpAccBisupRcvdBytes Counter32, cSpAccHCBisupRcvdBytes Counter64, cSpAccBisupSentPackets Counter32, cSpAccHCBisupSentPackets Counter64, cSpAccBisupSentBytes Counter32, cSpAccHCBisupSentBytes Counter64, cSpAccSisupRcvdPackets Counter32, cSpAccHCSisupRcvdPackets Counter64, cSpAccSisupRcvdBytes Counter32, cSpAccHCSisupRcvdBytes Counter64, cSpAccSisupSentPackets Counter32, cSpAccHCSisupSentPackets Counter64, cSpAccSisupSentBytes Counter32, cSpAccHCSisupSentBytes Counter64, cSpAccSpare11RcvdPackets Counter32, cSpAccHCSpare11RcvdPackets Counter64, cSpAccSpare11RcvdBytes Counter32, cSpAccHCSpare11RcvdBytes Counter64, cSpAccSpare11SentPackets Counter32, cSpAccHCSpare11SentPackets Counter64, cSpAccSpare11SentBytes Counter32, cSpAccHCSpare11SentBytes Counter64, cSpAccSpare12RcvdPackets Counter32, cSpAccHCSpare12RcvdPackets Counter64, cSpAccSpare12RcvdBytes Counter32, cSpAccHCSpare12RcvdBytes Counter64, cSpAccSpare12SentPackets Counter32, cSpAccHCSpare12SentPackets Counter64, cSpAccSpare12SentBytes Counter32, cSpAccHCSpare12SentBytes Counter64, cSpAccSpare13RcvdPackets Counter32, cSpAccHCSpare13RcvdPackets Counter64, cSpAccSpare13RcvdBytes Counter32, cSpAccHCSpare13RcvdBytes Counter64, cSpAccSpare13SentPackets Counter32, cSpAccHCSpare13SentPackets Counter64, cSpAccSpare13SentBytes Counter32, cSpAccHCSpare13SentBytes Counter64, cSpAccSpare14RcvdPackets Counter32, cSpAccHCSpare14RcvdPackets Counter64, cSpAccSpare14RcvdBytes Counter32, cSpAccHCSpare14RcvdBytes Counter64, cSpAccSpare14SentPackets Counter32, cSpAccHCSpare14SentPackets Counter64, cSpAccSpare14SentBytes Counter32, cSpAccHCSpare14SentBytes Counter64, cSpAccSpare15RcvdPackets Counter32, cSpAccHCSpare15RcvdPackets Counter64, cSpAccSpare15RcvdBytes Counter32, cSpAccHCSpare15RcvdBytes Counter64, cSpAccSpare15SentPackets Counter32, cSpAccHCSpare15SentPackets Counter64, cSpAccSpare15SentBytes Counter32, cSpAccHCSpare15SentBytes Counter64 } cSpAccTableId OBJECT-TYPE SYNTAX INTEGER { passed(1), violation(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The accounting table identifier. 'passed' : signifies that this table instance represents statistics for packets that matched an ACL in the linkset's inbound ACL and in the outbound ACL. 'violation' : signifies that this table instance represents statistics for packets that did not match an ACL in the linkset's inbound ACL and in the outbound ACL." ::= { cSpAccountingTableEntry 1 } cSpAccDpc OBJECT-TYPE SYNTAX CSpPointCode MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination point code." ::= { cSpAccountingTableEntry 2 } cSpAccOpc OBJECT-TYPE SYNTAX CSpPointCode MAX-ACCESS not-accessible STATUS current DESCRIPTION "The origin point code." ::= { cSpAccountingTableEntry 3 } cSpAccRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of all received packets for this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 4 } cSpAccHCRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of all received packets for this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccRcvdPackets ." ::= { cSpAccountingTableEntry 5 } cSpAccSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of all transmitted packets for this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 6 } cSpAccHCSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of all transmitted packets for this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSentPackets ." ::= { cSpAccountingTableEntry 7 } cSpAccRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of all received bytes for this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 8 } cSpAccHCRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of all received bytes for this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccRcvdBytes ." ::= { cSpAccountingTableEntry 9 } cSpAccSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of all transmitted bytes for this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 10 } cSpAccHCSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of all transmitted bytes for this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSentBytes ." ::= { cSpAccountingTableEntry 11 } cSpAccSnmmRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Management (SNM) packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 12 } cSpAccHCSnmmRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Management (SNM) packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSnmmRcvdPackets ." ::= { cSpAccountingTableEntry 13 } cSpAccSnmmRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes contained in the Signalling Network Management (SNM) messages received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 14 } cSpAccHCSnmmRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes contained in the Signalling Network Management (SNM) messages received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSnmmRcvdBytes ." ::= { cSpAccountingTableEntry 15 } cSpAccSnmmSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Management (SNM) packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 16 } cSpAccHCSnmmSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Management (SNM) packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSnmmSentPackets ." ::= { cSpAccountingTableEntry 17 } cSpAccSnmmSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Management (SNM) bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 18 } cSpAccHCSnmmSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Management (SNM) bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSnmmSentBytes ." ::= { cSpAccountingTableEntry 19 } cSpAccSntmRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Testing and maintenance (MTN) packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 20 } cSpAccHCSntmRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Testing and maintenance (MTN) packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSntmRcvdPackets ." ::= { cSpAccountingTableEntry 21 } cSpAccSntmRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Testing and maintenance (MTN) bytes received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 22 } cSpAccHCSntmRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Testing and maintenance (MTN) bytes received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSntmRcvdBytes ." ::= { cSpAccountingTableEntry 23 } cSpAccSntmSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Testing and maintenance (MTN) packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 24 } cSpAccHCSntmSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Testing and maintenance (MTN) packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSntmSentPackets ." ::= { cSpAccountingTableEntry 25 } cSpAccSntmSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Testing and maintenance (MTN) bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 26 } cSpAccHCSntmSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signalling Network Testing and maintenance (MTN) bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSntmSentBytes ." ::= { cSpAccountingTableEntry 27 } cSpAccSpare2RcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 2 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 28 } cSpAccHCSpare2RcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 2 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare2RcvdPackets ." ::= { cSpAccountingTableEntry 29 } cSpAccSpare2RcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 2 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 30 } cSpAccHCSpare2RcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 2 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare2RcvdBytes ." ::= { cSpAccountingTableEntry 31 } cSpAccSpare2SentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 2 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 32 } cSpAccHCSpare2SentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 2 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare2SentPackets ." ::= { cSpAccountingTableEntry 33 } cSpAccSpare2SentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 2 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 34 } cSpAccHCSpare2SentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 2 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare2SentBytes ." ::= { cSpAccountingTableEntry 35 } cSpAccSccpRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signaling Connection Control Part (SCCP) packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 36 } cSpAccHCSccpRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signaling Connection Control Part (SCCP) packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSccpRcvdPackets ." ::= { cSpAccountingTableEntry 37 } cSpAccSccpRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signaling Connection Control Part (SCCP) bytes received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 38 } cSpAccHCSccpRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signaling Connection Control Part (SCCP) bytes received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSccpRcvdBytes ." ::= { cSpAccountingTableEntry 39 } cSpAccSccpSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signaling Connection Control Part (SCCP) packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 40 } cSpAccHCSccpSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signaling Connection Control Part (SCCP) packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSccpSentPackets ." ::= { cSpAccountingTableEntry 41 } cSpAccSccpSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signaling Connection Control Part (SCCP) bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 42 } cSpAccHCSccpSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Signaling Connection Control Part (SCCP) bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSccpSentBytes ." ::= { cSpAccountingTableEntry 43 } cSpAccTupRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Telephone User Part (TUP) packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 44 } cSpAccHCTupRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Telephone User Part (TUP) packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccTupRcvdPackets ." ::= { cSpAccountingTableEntry 45 } cSpAccTupRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Telephone User Part (TUP) bytes received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 46 } cSpAccHCTupRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Telephone User Part (TUP) bytes received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccTupRcvdBytes ." ::= { cSpAccountingTableEntry 47 } cSpAccTupSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Telephone User Part (TUP) packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 48 } cSpAccHCTupSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Telephone User Part (TUP) packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccTupSentPackets ." ::= { cSpAccountingTableEntry 49 } cSpAccTupSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Telephone User Part (TUP) bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 50 } cSpAccHCTupSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Telephone User Part (TUP) bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccTupSentBytes ." ::= { cSpAccountingTableEntry 51 } cSpAccIsupRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ISDN User Part (ISUP) packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 52 } cSpAccHCIsupRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ISDN User Part (ISUP) packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccIsupRcvdPackets ." ::= { cSpAccountingTableEntry 53 } cSpAccIsupRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ISDN User Part (ISUP) bytes received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 54 } cSpAccHCIsupRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ISDN User Part (ISUP) bytes received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccIsupRcvdBytes ." ::= { cSpAccountingTableEntry 55 } cSpAccIsupSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ISDN User Part (ISUP) packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 56 } cSpAccHCIsupSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ISDN User Part (ISUP) packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccIsupSentPackets ." ::= { cSpAccountingTableEntry 57 } cSpAccIsupSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ISDN User Part (ISUP) bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 58 } cSpAccHCIsupSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ISDN User Part (ISUP) bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccIsupSentBytes ." ::= { cSpAccountingTableEntry 59 } cSpAccDupcRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Data User Part (call and circuit-related messages) - Dupc packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 60 } cSpAccHCDupcRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Data User Part (call and circuit-related messages) - Dupc packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccDupcRcvdPackets ." ::= { cSpAccountingTableEntry 61 } cSpAccDupcRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupc bytes received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 62 } cSpAccHCDupcRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupc bytes received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccDupcRcvdBytes ." ::= { cSpAccountingTableEntry 63 } cSpAccDupcSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupc packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 64 } cSpAccHCDupcSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupc packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccDupcSentPackets ." ::= { cSpAccountingTableEntry 65 } cSpAccDupcSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupc bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 66 } cSpAccHCDupcSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupc bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccDupcSentBytes ." ::= { cSpAccountingTableEntry 67 } cSpAccDupfRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Data User Part (facility registration and cancellation messages) - Dupf packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 68 } cSpAccHCDupfRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Data User Part (facility registration and cancellation messages) - Dupf packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccDupfRcvdPackets ." ::= { cSpAccountingTableEntry 69 } cSpAccDupfRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupf bytes received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 70 } cSpAccHCDupfRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupf bytes received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccDupfRcvdBytes ." ::= { cSpAccountingTableEntry 71 } cSpAccDupfSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupf packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 72 } cSpAccHCDupfSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupf packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccDupfSentPackets ." ::= { cSpAccountingTableEntry 73 } cSpAccDupfSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupf bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 74 } cSpAccHCDupfSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Dupf bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccDupfSentBytes ." ::= { cSpAccountingTableEntry 75 } cSpAccMtupRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Reserved for MTP Testing User Part (Mtup) packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 76 } cSpAccHCMtupRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Reserved for MTP Testing User Part (Mtup) packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccMtupRcvdPackets ." ::= { cSpAccountingTableEntry 77 } cSpAccMtupRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Reserved for MTP Testing User Part (Mtup) bytes received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 78 } cSpAccHCMtupRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Reserved for MTP Testing User Part (Mtup) bytes received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccMtupRcvdBytes ." ::= { cSpAccountingTableEntry 79 } cSpAccMtupSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Reserved for MTP Testing User Part (Mtup) packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 80 } cSpAccHCMtupSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Reserved for MTP Testing User Part (Mtup) packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccMtupSentPackets ." ::= { cSpAccountingTableEntry 81 } cSpAccMtupSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Reserved for MTP Testing User Part (Mtup) bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 82 } cSpAccHCMtupSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Reserved for MTP Testing User Part (Mtup) bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccMtupSentBytes ." ::= { cSpAccountingTableEntry 83 } cSpAccBisupRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadband ISDN User Part (Bisup) packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 84 } cSpAccHCBisupRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadband ISDN User Part (Bisup) packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccBisupRcvdPackets ." ::= { cSpAccountingTableEntry 85 } cSpAccBisupRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadband ISDN User Part (Bisup) bytes received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 86 } cSpAccHCBisupRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadband ISDN User Part (Bisup) bytes received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccBisupRcvdBytes ." ::= { cSpAccountingTableEntry 87 } cSpAccBisupSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadband ISDN User Part (Bisup) packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 88 } cSpAccHCBisupSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadband ISDN User Part (Bisup) packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccBisupSentPackets ." ::= { cSpAccountingTableEntry 89 } cSpAccBisupSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadband ISDN User Part (Bisup) bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 90 } cSpAccHCBisupSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadband ISDN User Part (Bisup) bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccBisupSentBytes ." ::= { cSpAccountingTableEntry 91 } cSpAccSisupRcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Satellite ISDN User Part (Sisup) packets received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 92 } cSpAccHCSisupRcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Satellite ISDN User Part (Sisup) packets received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSisupRcvdPackets ." ::= { cSpAccountingTableEntry 93 } cSpAccSisupRcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Satellite ISDN User Part (Sisup) bytes received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 94 } cSpAccHCSisupRcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Satellite ISDN User Part (Sisup) bytes received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSisupRcvdBytes ." ::= { cSpAccountingTableEntry 95 } cSpAccSisupSentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Satellite ISDN User Part (Sisup) packets transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 96 } cSpAccHCSisupSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Satellite ISDN User Part (Sisup) packets transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSisupSentPackets ." ::= { cSpAccountingTableEntry 97 } cSpAccSisupSentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Satellite ISDN User Part (Sisup) bytes transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 98 } cSpAccHCSisupSentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Satellite ISDN User Part (Sisup) bytes transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSisupSentBytes ." ::= { cSpAccountingTableEntry 99 } cSpAccSpare11RcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 11 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 100 } cSpAccHCSpare11RcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 11 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare11RcvdPackets ." ::= { cSpAccountingTableEntry 101 } cSpAccSpare11RcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 11 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 102 } cSpAccHCSpare11RcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 11 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare11RcvdBytes ." ::= { cSpAccountingTableEntry 103 } cSpAccSpare11SentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 11 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 104 } cSpAccHCSpare11SentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 11 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare11SentPackets ." ::= { cSpAccountingTableEntry 105 } cSpAccSpare11SentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 11 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 106 } cSpAccHCSpare11SentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 11 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare11SentBytes ." ::= { cSpAccountingTableEntry 107 } cSpAccSpare12RcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 12 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 108 } cSpAccHCSpare12RcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 12 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare12RcvdPackets ." ::= { cSpAccountingTableEntry 109 } cSpAccSpare12RcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 12 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 110 } cSpAccHCSpare12RcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 12 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare12RcvdBytes ." ::= { cSpAccountingTableEntry 111 } cSpAccSpare12SentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 12 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 112 } cSpAccHCSpare12SentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 12 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare12SentPackets ." ::= { cSpAccountingTableEntry 113 } cSpAccSpare12SentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 12 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 114 } cSpAccHCSpare12SentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 12 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare12SentBytes ." ::= { cSpAccountingTableEntry 115 } cSpAccSpare13RcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 13 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 116 } cSpAccHCSpare13RcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 13 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare13RcvdPackets ." ::= { cSpAccountingTableEntry 117 } cSpAccSpare13RcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 13 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 118 } cSpAccHCSpare13RcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 13 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare13RcvdBytes ." ::= { cSpAccountingTableEntry 119 } cSpAccSpare13SentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 13 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 120 } cSpAccHCSpare13SentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 13 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare13SentPackets ." ::= { cSpAccountingTableEntry 121 } cSpAccSpare13SentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 13 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 122 } cSpAccHCSpare13SentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 13 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare13SentBytes ." ::= { cSpAccountingTableEntry 123 } cSpAccSpare14RcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 14 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 124 } cSpAccHCSpare14RcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 14 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare14RcvdPackets ." ::= { cSpAccountingTableEntry 125 } cSpAccSpare14RcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 14 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 126 } cSpAccHCSpare14RcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 14 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare14RcvdBytes ." ::= { cSpAccountingTableEntry 127 } cSpAccSpare14SentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 14 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 128 } cSpAccHCSpare14SentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 14 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare14SentPackets ." ::= { cSpAccountingTableEntry 129 } cSpAccSpare14SentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 14 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 130 } cSpAccHCSpare14SentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 15 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare15SentBytes ." ::= { cSpAccountingTableEntry 131 } cSpAccSpare15RcvdPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 15 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 132 } cSpAccHCSpare15RcvdPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 15 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare15RcvdPackets ." ::= { cSpAccountingTableEntry 133 } cSpAccSpare15RcvdBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 15 received on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 134 } cSpAccHCSpare15RcvdBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 15 received on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare15RcvdBytes ." ::= { cSpAccountingTableEntry 135 } cSpAccSpare15SentPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 15 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 136 } cSpAccHCSpare15SentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets with Service Indicator value 15 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare15SentPackets ." ::= { cSpAccountingTableEntry 137 } cSpAccSpare15SentBytes OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 15 transmitted on this linkset, DPC and OPC combination." ::= { cSpAccountingTableEntry 138 } cSpAccHCSpare15SentBytes OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes with Service Indicator value 15 transmitted on this linkset, DPC and OPC combination. This is the 64 bit version of cSpAccSpare15SentBytes ." ::= { cSpAccountingTableEntry 139 } -- ************************************************************* -- * * -- * SP - Notification Enable Objects * -- * * -- ************************************************************* cSpLsStateChangeNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The SP linkset notification truth value. 'true' Indicates that ciscoSpLinksetStateChange notification is to be generated when the state changes. That is, the notification generation is enabled. 'false' Indicates that ciscoSpLinksetStateChange notification generation is disabled." DEFVAL { true } ::= { cSpNotificationsEnable 1 } cSpLnkStateChangeNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The SP link notification truth value. 'true' Indicates that ciscoSpLinkStateChange notification is to be generated when the state changes. That is, the notification generation is enabled. 'false' Indicates that ciscoSpLinkStateChange notification generation is disabled." DEFVAL { true } ::= { cSpNotificationsEnable 2 } -- -- Notifications -- ciscoSpMIBNotificationPrefix OBJECT IDENTIFIER ::= { ciscoSpMIB 2 } ciscoSpMIBNotifications OBJECT IDENTIFIER ::= { ciscoSpMIBNotificationPrefix 0 } ciscoSpLinksetStateChange NOTIFICATION-TYPE OBJECTS { cSpLinksetState } STATUS current DESCRIPTION "The notification generated when a linkset changes to a new state. The value of cSpLinksetState indicates the new state." ::= { ciscoSpMIBNotifications 1 } ciscoSpLinkStateChange NOTIFICATION-TYPE OBJECTS { cSpLinkState } STATUS current DESCRIPTION "The notification generated when a SP link changes state. The value of cSpLinkState indicates the new state." ::= { ciscoSpMIBNotifications 2 } -- -- Conformance Information -- ciscoSpMIBConformance OBJECT IDENTIFIER ::= { ciscoSpMIB 3 } ciscoSpMIBCompliances OBJECT IDENTIFIER ::= { ciscoSpMIBConformance 1 } ciscoSpMIBGroups OBJECT IDENTIFIER ::= { ciscoSpMIBConformance 2 } -- Compliance ciscoSpMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Cisco SP MIB" MODULE -- this module MANDATORY-GROUPS { ciscoSpSwitchGroup, ciscoSpLinksetGroup, ciscoSpLinkGroup, ciscoSpRouteGroup, ciscoSpAccessListGroup, ciscoSpAccountingGroup, ciscoSpNotificationsEnableGroup } GROUP ciscoSpNotificationsGroup DESCRIPTION "This group is optional." ::= { ciscoSpMIBCompliances 1 } -- Units of Conformance ciscoSpSwitchGroup OBJECT-GROUP OBJECTS { cSpPointCode, cSpSs7Variant, cSpMtp2T01, cSpMtp2T02, cSpMtp2T03, cSpMtp2T4N, cSpMtp2T4E, cSpMtp2T05, cSpMtp2T06, cSpMtp2T07, cSpMtp2T08, cSpMtp3T01, cSpMtp3T02, cSpMtp3T03, cSpMtp3T04, cSpMtp3T05, cSpMtp3T06, cSpMtp3T07, cSpMtp3T08, cSpMtp3T10, cSpMtp3T11, cSpMtp3T12, cSpMtp3T13, cSpMtp3T14, cSpMtp3T15, cSpMtp3T16, cSpMtp3T17, cSpMtp3T18, cSpMtp3T19, cSpMtp3T20, cSpMtp3T21, cSpMtp3T22, cSpMtp3T23, cSpMtp3T24, cSpMtp3T25, cSpMtp3T26, cSpMtp3T27, cSpMtp3T28, cSpMtp3T29, cSpMtp3T30, cSpMtp3T31, cSpMtp3T32, cSpMtp3T33, cSpMtp3T34 } STATUS current DESCRIPTION "SP main objects." ::= { ciscoSpMIBGroups 1 } ciscoSpLinksetGroup OBJECT-GROUP OBJECTS { cSpLinksetAdjacentPointCode, cSpLinksetState, cSpLinksetInboundAcl, cSpLinksetOutboundAcl, cSpLinksetSnmmRouteTableName, cSpLinksetSntmRouteTableName, cSpLinksetSpare2RouteTableName, cSpLinksetSccpRouteTableName, cSpLinksetTupRouteTableName, cSpLinksetIsupRouteTableName, cSpLinksetDupcRouteTableName, cSpLinksetDupfRouteTableName, cSpLinksetMtupRouteTableName, cSpLinksetBisupRouteTableName, cSpLinksetSisupRouteTableName, cSpLinksetSpare11RouteTableName, cSpLinksetSpare12RouteTableName, cSpLinksetSpare13RouteTableName, cSpLinksetSpare14RouteTableName, cSpLinksetSpare15RouteTableName, cSpLinksetAccountingEnabled, cSpLinksetNumLinks, cSpLinksetPacketsSent, cSpLinksetHCPacketsSent, cSpLinksetPacketsRcvd, cSpLinksetHCPacketsRcvd, cSpLinksetBytesSent, cSpLinksetHCBytesSent, cSpLinksetBytesRcvd, cSpLinksetHCBytesRcvd, cSpLinksetDurationInService, cSpLinksetDurationOutService, cSpLinksetMtp2T01, cSpLinksetMtp2T02, cSpLinksetMtp2T03, cSpLinksetMtp2T4N, cSpLinksetMtp2T4E, cSpLinksetMtp2T05, cSpLinksetMtp2T06, cSpLinksetMtp2T07, cSpLinksetMtp2T08, cSpLinksetMtp3T01, cSpLinksetMtp3T02, cSpLinksetMtp3T03, cSpLinksetMtp3T04, cSpLinksetMtp3T05, cSpLinksetMtp3T06, cSpLinksetMtp3T07, cSpLinksetMtp3T08, cSpLinksetMtp3T10, cSpLinksetMtp3T11, cSpLinksetMtp3T12, cSpLinksetMtp3T13, cSpLinksetMtp3T14, cSpLinksetMtp3T15, cSpLinksetMtp3T16, cSpLinksetMtp3T17, cSpLinksetMtp3T18, cSpLinksetMtp3T19, cSpLinksetMtp3T20, cSpLinksetMtp3T21, cSpLinksetMtp3T22, cSpLinksetMtp3T23, cSpLinksetMtp3T24, cSpLinksetMtp3T25, cSpLinksetMtp3T26, cSpLinksetMtp3T27, cSpLinksetMtp3T28, cSpLinksetMtp3T29, cSpLinksetMtp3T30, cSpLinksetMtp3T31, cSpLinksetMtp3T32, cSpLinksetMtp3T33, cSpLinksetMtp3T34 } STATUS current DESCRIPTION "SP linkset objects." ::= { ciscoSpMIBGroups 2 } ciscoSpLinkGroup OBJECT-GROUP OBJECTS { cSpLinkState, cSpLinkType, cSpLinkifIndex, cSpLinkSctpAssociation, cSpLinkMtp3PacketsRcvd, cSpLinkMtp3PacketsSent, cSpLinkHCMtp3PacketsRcvd, cSpLinkHCMtp3PacketsSent, cSpLinkMtp3BytesRcvd, cSpLinkMtp3BytesSent, cSpLinkHCMtp3BytesRcvd, cSpLinkHCMtp3BytesSent, cSpLinkMtp2T01, cSpLinkMtp2T02, cSpLinkMtp2T03, cSpLinkMtp2T4N, cSpLinkMtp2T4E, cSpLinkMtp2T05, cSpLinkMtp2T06, cSpLinkMtp2T07, cSpLinkMtp2T08, cSpLinkMtp3T01, cSpLinkMtp3T02, cSpLinkMtp3T03, cSpLinkMtp3T04, cSpLinkMtp3T05, cSpLinkMtp3T06, cSpLinkMtp3T07, cSpLinkMtp3T08, cSpLinkMtp3T10, cSpLinkMtp3T11, cSpLinkMtp3T12, cSpLinkMtp3T13, cSpLinkMtp3T14, cSpLinkMtp3T15, cSpLinkMtp3T16, cSpLinkMtp3T17, cSpLinkMtp3T18, cSpLinkMtp3T19, cSpLinkMtp3T20, cSpLinkMtp3T21, cSpLinkMtp3T22, cSpLinkMtp3T23, cSpLinkMtp3T24, cSpLinkMtp3T25, cSpLinkMtp3T26, cSpLinkMtp3T27, cSpLinkMtp3T28, cSpLinkMtp3T29, cSpLinkMtp3T30, cSpLinkMtp3T31, cSpLinkMtp3T32, cSpLinkMtp3T33, cSpLinkMtp3T34, cSpLinkXmitQueueDepth, cSpLinkXmitQueueDepthHigh, cSpLinkXmitQueueDepthHighReset, cSpLinkCongestionState, cSpLinkCongestionAbate1, cSpLinkCongestionAbate2, cSpLinkCongestionAbate3, cSpLinkCongestionOnset1, cSpLinkCongestionOnset2, cSpLinkCongestionOnset3, cSpLinkSigLinkTest, cSpLinkQ752T1E1, cSpLinkQ752T1E2, cSpLinkQ752T1E3, cSpLinkQ752T1E4, cSpLinkQ752T1E5, cSpLinkQ752T1E6, cSpLinkQ752T1E7, cSpLinkQ752T1E8, cSpLinkQ752T1E9, cSpLinkQ752T1E10, cSpLinkQ752T1E11, cSpLinkQ752T2E1, cSpLinkQ752T2E5, cSpLinkQ752T2E6, cSpLinkQ752T2E7, cSpLinkQ752T2E9, cSpLinkQ752T2E10, cSpLinkQ752T2E15, cSpLinkQ752T2E16, cSpLinkQ752T2E18, cSpLinkMtp3PacketsRetrans, -- Q752/3.2 cSpLinkMtp3BytesRetrans, -- Q752/3.2 cSpLinkQ752T3E6, cSpLinkQ752T3E7, cSpLinkQ752T3E10L1, cSpLinkQ752T3E10L2, cSpLinkQ752T3E10L3, cSpLinkQ752T3E11L1, cSpLinkQ752T3E11L2, cSpLinkQ752T3E11L3 } STATUS current DESCRIPTION "SP link objects." ::= { ciscoSpMIBGroups 3 } ciscoSpRouteGroup OBJECT-GROUP OBJECTS { cSpRouteStatus } STATUS current DESCRIPTION "SP route table objects." ::= { ciscoSpMIBGroups 4 } ciscoSpAccessListGroup OBJECT-GROUP OBJECTS { cSpAclType, cSpAclDpc, cSpAclDpcMask, cSpAclOpc, cSpAclOpcMask, cSpAclSi, cSpAclPattern, cSpAclOffset, cSpAclAction } STATUS current DESCRIPTION "SP access control list objects." ::= { ciscoSpMIBGroups 5 } ciscoSpAccountingGroup OBJECT-GROUP OBJECTS { cSpAccRcvdPackets, cSpAccHCRcvdPackets, cSpAccSentPackets, cSpAccHCSentPackets, cSpAccRcvdBytes, cSpAccHCRcvdBytes, cSpAccSentBytes, cSpAccHCSentBytes, cSpAccSnmmRcvdPackets, cSpAccHCSnmmRcvdPackets, cSpAccSnmmRcvdBytes, cSpAccHCSnmmRcvdBytes, cSpAccSnmmSentPackets, cSpAccHCSnmmSentPackets, cSpAccSnmmSentBytes, cSpAccHCSnmmSentBytes, cSpAccSntmRcvdPackets, cSpAccHCSntmRcvdPackets, cSpAccSntmRcvdBytes, cSpAccHCSntmRcvdBytes, cSpAccSntmSentPackets, cSpAccHCSntmSentPackets, cSpAccSntmSentBytes, cSpAccHCSntmSentBytes, cSpAccSpare2RcvdPackets, cSpAccHCSpare2RcvdPackets, cSpAccSpare2RcvdBytes, cSpAccHCSpare2RcvdBytes, cSpAccSpare2SentPackets, cSpAccHCSpare2SentPackets, cSpAccSpare2SentBytes, cSpAccHCSpare2SentBytes, cSpAccSccpRcvdPackets, cSpAccHCSccpRcvdPackets, cSpAccSccpRcvdBytes, cSpAccHCSccpRcvdBytes, cSpAccSccpSentPackets, cSpAccHCSccpSentPackets, cSpAccSccpSentBytes, cSpAccHCSccpSentBytes, cSpAccTupRcvdPackets, cSpAccHCTupRcvdPackets, cSpAccTupRcvdBytes, cSpAccHCTupRcvdBytes, cSpAccTupSentPackets, cSpAccHCTupSentPackets, cSpAccTupSentBytes, cSpAccHCTupSentBytes, cSpAccIsupRcvdPackets, cSpAccHCIsupRcvdPackets, cSpAccIsupRcvdBytes, cSpAccHCIsupRcvdBytes, cSpAccIsupSentPackets, cSpAccHCIsupSentPackets, cSpAccIsupSentBytes, cSpAccHCIsupSentBytes, cSpAccDupcRcvdPackets, cSpAccHCDupcRcvdPackets, cSpAccDupcRcvdBytes, cSpAccHCDupcRcvdBytes, cSpAccDupcSentPackets, cSpAccHCDupcSentPackets, cSpAccDupcSentBytes, cSpAccHCDupcSentBytes, cSpAccDupfRcvdPackets, cSpAccHCDupfRcvdPackets, cSpAccDupfRcvdBytes, cSpAccHCDupfRcvdBytes, cSpAccDupfSentPackets, cSpAccHCDupfSentPackets, cSpAccDupfSentBytes, cSpAccHCDupfSentBytes, cSpAccMtupRcvdPackets, cSpAccHCMtupRcvdPackets, cSpAccMtupRcvdBytes, cSpAccHCMtupRcvdBytes, cSpAccMtupSentPackets, cSpAccHCMtupSentPackets, cSpAccMtupSentBytes, cSpAccHCMtupSentBytes, cSpAccBisupRcvdPackets, cSpAccHCBisupRcvdPackets, cSpAccBisupRcvdBytes, cSpAccHCBisupRcvdBytes, cSpAccBisupSentPackets, cSpAccHCBisupSentPackets, cSpAccBisupSentBytes, cSpAccHCBisupSentBytes, cSpAccSisupRcvdPackets, cSpAccHCSisupRcvdPackets, cSpAccSisupRcvdBytes, cSpAccHCSisupRcvdBytes, cSpAccSisupSentPackets, cSpAccHCSisupSentPackets, cSpAccSisupSentBytes, cSpAccHCSisupSentBytes, cSpAccSpare11RcvdPackets, cSpAccHCSpare11RcvdPackets, cSpAccSpare11RcvdBytes, cSpAccHCSpare11RcvdBytes, cSpAccSpare11SentPackets, cSpAccHCSpare11SentPackets, cSpAccSpare11SentBytes, cSpAccHCSpare11SentBytes, cSpAccSpare12RcvdPackets, cSpAccHCSpare12RcvdPackets, cSpAccSpare12RcvdBytes, cSpAccHCSpare12RcvdBytes, cSpAccSpare12SentPackets, cSpAccHCSpare12SentPackets, cSpAccSpare12SentBytes, cSpAccHCSpare12SentBytes, cSpAccSpare13RcvdPackets, cSpAccHCSpare13RcvdPackets, cSpAccSpare13RcvdBytes, cSpAccHCSpare13RcvdBytes, cSpAccSpare13SentPackets, cSpAccHCSpare13SentPackets, cSpAccSpare13SentBytes, cSpAccHCSpare13SentBytes, cSpAccSpare14RcvdPackets, cSpAccHCSpare14RcvdPackets, cSpAccSpare14RcvdBytes, cSpAccHCSpare14RcvdBytes, cSpAccSpare14SentPackets, cSpAccHCSpare14SentPackets, cSpAccSpare14SentBytes, cSpAccHCSpare14SentBytes, cSpAccSpare15RcvdPackets, cSpAccHCSpare15RcvdPackets, cSpAccSpare15RcvdBytes, cSpAccHCSpare15RcvdBytes, cSpAccSpare15SentPackets, cSpAccHCSpare15SentPackets, cSpAccSpare15SentBytes, cSpAccHCSpare15SentBytes } STATUS current DESCRIPTION "SP accounting objects." ::= { ciscoSpMIBGroups 6 } ciscoSpNotificationsEnableGroup OBJECT-GROUP OBJECTS { cSpLsStateChangeNotifEnabled, cSpLnkStateChangeNotifEnabled } STATUS current DESCRIPTION "SP enable notification objects." ::= { ciscoSpMIBGroups 7 } ciscoSpNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { ciscoSpLinksetStateChange, ciscoSpLinkStateChange } STATUS current DESCRIPTION "The collection of notifications used to indicate wrapped and unwrapped node state information." ::= { ciscoSpMIBGroups 8 } END