-- ***************************************************************** -- Disman Expression MIB -- July 1997, Sandra C. Durham -- Copyright (c) 1997, 1998 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** -- This mib was extracted from the first draft of the expression mib EXPRESSION-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Gauge32, Unsigned32, Counter32, Counter64, zeroDotZero, IpAddress FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, TruthValue, TimeStamp, DisplayString FROM SNMPv2-TC ciscoExperiment FROM CISCO-SMI sysUpTime FROM RFC1213-MIB MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; expressionMIB MODULE-IDENTITY LAST-UPDATED "200511240000Z" ORGANIZATION "IETF Distributed Management Working Group" CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-snmp@cisco.com" DESCRIPTION "The MIB module for defining expressions of MIB objects for network management purposes. This MIB is an early snapshot of work done by the IETF's Distributed Management working group. After this snapshot was taken, the MIB was modified, had new OIDs assigned, and then published as RFC 2982." REVISION "200511240000Z" DESCRIPTION "Imported Unsigned32 from SNMPv2-SMI." REVISION "9802251700Z" DESCRIPTION "Initial version of the mib module." ::= { ciscoExperiment 22 } ExpressionName ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is a refinement of DisplayString to represent an identification for an expression. An ExpressionName corresponds one-to-one to an ExpressionIndex. This identification of an expression is subject to change only by administrative request." SYNTAX OCTET STRING (SIZE (1..64)) ExpressionIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An integer shorthand identification for an expression. An ExpressionIndex corresponds one-to-one to an ExpressionName. Once assigned an ExpressionIndex may not be changed." SYNTAX Unsigned32 (1..4294967295) ExpressionIndexOrZero ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Either an ExpressionIndex or zero. The meaning of zero depends on the DESCRIPTION of the object." SYNTAX Unsigned32 (0..4294967295) expressionMIBObjects OBJECT IDENTIFIER ::= { expressionMIB 1 } expResource OBJECT IDENTIFIER ::= { expressionMIBObjects 1 } expNames OBJECT IDENTIFIER ::= { expressionMIBObjects 2 } expDefine OBJECT IDENTIFIER ::= { expressionMIBObjects 3 } expValue OBJECT IDENTIFIER ::= { expressionMIBObjects 4 } -- Wildcarding Example -- This example refers to tables and objects defined below. It may well -- make more sense after reading those definitions. -- An expression may use wildcarded MIB objects that result in multiple -- values for the expression. To specify a wildcarded MIB object a -- management application leaves off part or all of the instance portion -- of the object identifier, and sets expObjectWildcard to true(1) for -- that object. For our example we'll use a counter of total blessings -- from a table of people. Another table, indexed by town and person -- has blessings just from that town. -- So the index clauses are: -- personEntry OBJECT-TYPE -- ... -- INDEX { personIndex } -- And: -- townPersonEntry OBJECT-TYPE -- ... -- INDEX { townIndex, personIndex } -- In our friendly application we may have entered our expression as: -- 100 * townPersonBlessings.976.* / personBlessings.* -- What goes in expExpression is: -- 100*$1/$2 -- For example purposes we'll use some slightly far-fetched OIDs, but -- the weirdity won't matter. The People MIB is 1.3.6.1.99.7 and the -- Town MIB is 1.3.6.1.99.11, so for our two counters the OIDs are: -- personBlessings 1.3.6.1.99.7.1.3.1.4 -- townPersonBlessings 1.3.6.1.99.11.1.2.1.9 -- The rule for wildcards is that all the wildcarded parts have to match -- exactly. In this case that means we have to hardwire the town and -- only the personIndex can be wildcarded. So our values for expObjectID -- are: -- 1.3.6.1.99.7.1.3.1.4 -- 1.3.6.1.99.11.1.2.1.9.976 -- We're hardwired to townIndex 976 and personIndex is allowed to vary. -- The value of expExpressionPrefix can be either of those two counter -- OIDs (including the instance fragment in the second case), since -- either of them takes you to a MIB definition where you can look at -- the INDEX clause and figure out what's been left off. What's been -- left off doesn't have to work out to be the same object, but it -- does have to work out to be the same values (semantics) for the -- result to make sense. Note that the agent can not typically check -- such semantics and if given nonsense will return nonsense. -- If we have people numbered 6, 19, and 42 in town number 976, the -- successive values of expValueInstance will be: -- 0.0.6 -- 0.0.19 -- 0.0.42 -- So there will be three values in expValueTable, with those OIDs as -- the expValueInstance part of their indexing. -- Resource Control expResourceDeltaMinimum OBJECT-TYPE SYNTAX Integer32 (-1 | 1..600) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum expExpressionDeltaInterval this system will accept. A system may use the larger values of this minimum to lessen the impact of constantly computing deltas. The value -1 indicates this system will not accept deltaValue as a value for expObjectSampleType. Unless explicitly resource limited, a system's value for this object should be 1. Changing this value will not invalidate an existing setting of expObjectSampleType." ::= { expResource 1 } expResourceDeltaWildcardInstanceMaximum OBJECT-TYPE SYNTAX Unsigned32 UNITS "instances" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of dynamic instance entries this system will support for wildcarded delta objects in expressions. These are the entries that maintain state, one for each instance of each deltaValue object for each value of an expression. A value of 0 indicates no preset limit, that is, the limit is dynamic based on system operation and resources. Unless explicitly resource limited, a system's value for this object should be 0. Changing this value will not eliminate or inhibit existing delta wildcard instance objects but will prevent the creation of more such objects." ::= { expResource 2 } expResourceDeltaWildcardInstances OBJECT-TYPE SYNTAX Gauge32 UNITS "instances" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of currently active instance entries as defined for expResourceDeltaWildcardInstanceMaximum." ::= { expResource 3 } expResourceDeltaWildcardInstancesHigh OBJECT-TYPE SYNTAX Gauge32 UNITS "instances" MAX-ACCESS read-only STATUS current DESCRIPTION "The highest value of expResourceDeltaWildcardInstances that has occurred since initialization of the management system." ::= { expResource 4 } expResourceDeltaWildcardInstanceResourceLacks OBJECT-TYPE SYNTAX Counter32 UNITS "instances" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this system could not evaluate an expression because that would have created a value instance in excess of expResourceDeltaWildcardInstanceMaximum." ::= { expResource 5 } -- Naming & Creation expNameLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime the last time an expression was created or deleted or had its name changed using expExpressionName." ::= { expNames 1 } expNameHighestIndex OBJECT-TYPE SYNTAX ExpressionIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The highest value of ExpressionIndex ever assigned on this system. Preferrably this value is preserved across system reboots. A managed system that is unable to store expressions across reboots need not preserve this value across reboots. If all expression-creating applications cooperate, they may use this to avoid reusing an ExpressionIndex. To do so, attempt creation of a new entry with this value + 1 as the value of expExpressionIndex. Although reusing ExpressionIndexes could lead to an application receiving a misunderstood value, it is a matter of local management policy whether to reuse them." ::= { expNames 2 } -- Name Creation Table expNameTable OBJECT-TYPE SYNTAX SEQUENCE OF ExpNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of expression names, for creating and deleting expressions." ::= { expNames 3 } expNameEntry OBJECT-TYPE SYNTAX ExpNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single expression. New expressions can be created using expNameStatus. To create an expression first create the named entry in this table. Then use expExpressionIndex to populate expExpressionTable and expObjectTable. For expression evaluation to succeed all related entries in expNameTable, expExpressionTable, and expObjectTable must be 'active'. If these conditions are not met the corresponding values in expValue simply are not instantiated. Deleting an entry deletes all related entries in expExpressionTable and expObjectTable. Because of the relationships among the multiple tables for an expression (expNameTable, expExpressionTable, expObjectTable, and expValueTable) and the SNMP rules for independence in setting object values, it is necessary to do final error checking when an expression is evaluated, that is, when one of its instances in expValueTable is read. Earlier checking need not be done and an implementation may not impose any ordering on the creation of objects related to an expression other than to require values for expName and expExpressionIndex before any other related objects can be created. To maintain security of MIB information, when creating a new row in this table, the managed system must record the security credentials of the requester. If the subsequent expression includes objects with expObjectSampleType 'deltaValue' the evaluation of that expression takes place under the security credentials of the creator of its expNameEntry." INDEX { expName } ::= { expNameTable 1 } ExpNameEntry ::= SEQUENCE { expName ExpressionName, expExpressionIndex ExpressionIndex, expNameStatus RowStatus } expName OBJECT-TYPE SYNTAX ExpressionName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the expression. Choosing names with useful lexical ordering supports using GetNext or GetBulk to retrieve a useful subset of the table." ::= { expNameEntry 1 } expExpressionIndex OBJECT-TYPE SYNTAX ExpressionIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The numeric identification of the expression. Applications may select this number in ascending numerical order by using expNameHighestIndex as a hint or may use any other acceptable, unused number. Once set this value may not be set to a different value." ::= { expNameEntry 2 } expNameStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The control that allows creation/deletion of entries." ::= { expNameEntry 3 } -- Definition -- Expression Definition Table expExpressionTable OBJECT-TYPE SYNTAX SEQUENCE OF ExpExpressionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of expression definitions." ::= { expDefine 1 } expExpressionEntry OBJECT-TYPE SYNTAX ExpExpressionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single expression. An entry appears in this table when an entry is created in expNameTable. Deleting that expNameTable entry automatically deletes this entry and its associated expObjectTable entries. Values of read-write objects in this table may be changed at any time." INDEX { expExpressionIndex } ::= { expExpressionTable 1 } ExpExpressionEntry ::= SEQUENCE { expExpressionName ExpressionName, expExpression OCTET STRING, expExpressionValueType INTEGER, expExpressionComment DisplayString, expExpressionDeltaInterval Integer32, expExpressionPrefix OBJECT IDENTIFIER, expExpressionErrors Counter32, expExpressionErrorTime TimeStamp, expExpressionErrorIndex Integer32, expExpressionError INTEGER, expExpressionInstance OBJECT IDENTIFIER, expExpressionOwner DisplayString } expExpressionName OBJECT-TYPE SYNTAX ExpressionName MAX-ACCESS read-write STATUS current DESCRIPTION "The unique name of the expression, the same as expName. Use this object to change the expression's name without changing its expExpressionIndex." ::= { expExpressionEntry 1 } expExpression OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..1024)) MAX-ACCESS read-write STATUS current DESCRIPTION "The expression to be evaluated. This object is the same as a DisplayString (RFC 1903) except for its maximum length. Except for the variable names the expression is in ANSI C syntax. Only the subset of ANSI C operators and functions listed here is allowed. Variables are expressed as a dollar sign ('$') and an integer that corresponds to an expObjectIndex. An example of a valid expression is: ($1-$5)*100 Expressions may not be recursive, that is although an expression may use the results of another expression, it may not contain any variable that is directly or indirectly a result of its own evaluation. The only allowed operators are: ( ) - (unary) + - * / % & | ^ << >> ~ ! && || == != > >= < <= Note the parentheses are included for parenthesizing the expression, not for casting data types. The only constant types defined are: int (32-bit signed) long (64-bit signed) unsigned int unsigned long hexadecimal character string oid The default type for a positive integer is int unless it is too large in which case it is long. All but oid are as defined for ANSI C. Note that a hexadecimal constant may end up as a scalar or an array of 8-bit integers. A string constant is enclosed in double quotes and may contain back-slashed individual characters as in ANSI C. An oid constant comprises 32-bit, unsigned integers and at least one period, for example: 0. .0 1.3.6.1 Integer-typed objects are treated as 32- or 64-bit, signed or unsigned integers, as appropriate. The results of mixing them are as for ANSI C, including the type of the result. Note that a 32-bit value is thus promoted to 64 bits only in an operation with a 64-bit value. There is no provision for larger values to handle overflow. Relative to SNMP data types, a resulting value becomes unsigned when calculating it uses any unsigned value, including a counter. To force the final value to be of data type counter the expression must explicitly use the counter32() or counter64() function (defined below). OCTET STRINGS and OBJECT IDENTIFIERs are treated as 1-based arrays of unsigned 8-bit integers and unsigned 32-bit integers, respectively. IpAddresses are treated as 32-bit, unsigned integers in network byte order, that is, the hex version of 255.0.0.0 is 0xff000000. Conditional expressions result in a 32-bit, unsigned integer of value 0 for false or 1 for true. When an arbitrary value is used as a boolean 0 is false and non-zero is true. Rules for the resulting data type from an operation, based on the operator: For << and >> the result is the same as the left hand operand. For &&, ||, ==, !=, <, <=, >, and >= the result is always Unsigned32. For unary - the result is always Integer32. For +, -, *, /, %, &, |, and ^ the result is promoted according to the following rules, in order from most to least preferred: If left hand and right hand operands are the same type, use that. If either side is Counter64, use that. If either side is IpAddress, use that. If either side is TimeTicks, use that. If either side is Counter32, use that. Otherwise use Unsigned32. The following rules say what operators apply with what data types. Any combination not explicitly defined does not work. For all operators any of the following can be the left hand or right hand operand: Integer32, Counter32, Unsigned32, Counter64. The operators +, -, *, /, %, <, <=, >, and >= also work with TimeTicks. The operators &, |, and ^ also work with IpAddress. The operators << and >> also work with IpAddress but only as the left hand operand. The + operator performs a concatenation of two OCTET STRINGs or two OBJECT IDENTIFIERs. The operators &, | perform bitwise operations on OCTET STRINGs. If the OCTET STRING happens to be a DisplayString the results may be meaningless, but the agent system does not check this as some such systems do not have this information. The operators << and >> perform bitwise operations on OCTET STRINGs appearing as the left hand operand. The only functions defined are: counter32 counter64 arraySection stringBegins stringEnds stringContains oidBegins oidEnds oidContains sum exists The following function definitions indicate their by naming the data type of the parameter in the parameter's position in the parameter list. The parameter must be of the type indicated and generally may be a constant, a MIB object, a function, or an expression. counter32(integer) - wrapped around an integer value counter32 forces Counter32 as a data type. counter64(integer) - similar to counter32 except that the resulting data type is 'counter64'. arraySection(array, integer, integer) - selects a piece of an array (i.e. part of an OCTET STRING or OBJECT IDENTIFIER). The integer arguments are in the range 0 to 4,294,967,295. The first is an initial array index (1-based) and the second is an ending array index. A value of 0 indicates first or last element, respectively. If the first element is larger than the array length the result is 0 length. If the second integer is less than or equal to the first, the result is 0 length. If the second is larger than the array length it indicates last element. stringBegins/Ends/Contains(octetString, octetString) - looks for the second string (which can be a string constant) in the first and returns the 1-based index where the match began. A return value of 0 indicates no match (i.e. boolean false). oidBegins/Ends/Contains(oid, oid) - looks for the second OID (which can be an OID constant) in the first and returns the the 1-based index where the match began. A return value of 0 indicates no match (i.e. boolean false). sum(integerObject*) - sums all availiable values of the wildcarded integer object, resulting in an integer scalar. Must be used with caution as it wraps on overflow with no notification. exists(anyTypeObject) - verifies the object instance exists. A return value of 0 indicates NoSuchInstance (i.e. boolean false)." ::= { expExpressionEntry 2 } expExpressionValueType OBJECT-TYPE SYNTAX INTEGER { counter32(1), unsignedOrGauge32(2), timeTicks(3), integer32(4), ipAddress(5), octetString(6), objectId(7), counter64(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of the expression value. One and only one of the value objects in expValueTable will be instantiated to match this type. If the result of the expression can not be made into this type, an invalidOperandType error will occur." DEFVAL { counter32 } ::= { expExpressionEntry 3 } expExpressionComment OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "A comment to explain the use or meaning of the expression." DEFVAL { "" } ::= { expExpressionEntry 4 } expExpressionDeltaInterval OBJECT-TYPE SYNTAX Integer32 (0..86400) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Sampling interval for objects in this expression with expObjectSampleType 'deltaValue'. This object is not instantiated if not applicable. A value of 0 indicates no automated sampling. In this case the delta is the difference from the last time the expression was evaluated. Note that this is subject to unpredictable delta times in the face of retries or multiple managers. A value greater than zero is the number of seconds between automated samples. Until the delta interval has expired once the delta for the object is effectively not instantiated and evaluating the expression has results as if the object itself were not instantiated. Note that delta values potentially consume large amounts of system CPU and memory. Delta state and processing must continue constantly even if the expression is not being used. That is, the expression is being evaluated every delta interval, even if no application is reading those values. For wildcarded objects this can be substantial overhead. Note that delta intervals, external expression value sampling intervals and delta intervals for expressions within other expressions can have unusual interactions as they are impossible to synchronize accurately. In general one interval embedded below another must be enough shorter that the higher sample sees relatively smooth, predictable behavior." DEFVAL { 0 } ::= { expExpressionEntry 5 } expExpressionPrefix OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "An object prefix to assist an application in determining the instance indexing to use in expValueTable, relieving the application of the need to scan the expObjectTable to determine such a prefix. See expObjectTable for information on wildcarded objects. If the expValueInstance portion of the value OID may be treated as a scalar (that is, normally, 0) the value of expExpressionPrefix is zero length, that is, no OID at all. Otherwise expExpressionPrefix is the value of any wildcarded instance of expObjectID for the expression. This is sufficient as the remainder, that is, the instance fragment relevant to instancing the values must be the same for all wildcarded objects in the expression." ::= { expExpressionEntry 6 } expExpressionErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of errors encountered while evaluating this expression. Note that an object in the expression not being accessible is not considered an error. It is a legitimate condition that causes the corresponding expression value not to be instantiated." ::= { expExpressionEntry 7 } expExpressionErrorTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime the last time an error caused a failure to evaluate this expression. This object is not instantiated if there have been no errors." ::= { expExpressionEntry 8 } expExpressionErrorIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 1-based character index into expExpression for where the error occurred. The value zero indicates irrelevance. This object is not instantiated if there have been no errors." ::= { expExpressionEntry 9 } expExpressionError OBJECT-TYPE SYNTAX INTEGER { invalidSyntax(1), undefinedObjectIndex(2), unrecognizedOperator(3), unrecognizedFunction(4), invalidOperandType(5), unmatchedParenthesis(6), tooManyWildcardValues(7), recursion(8), deltaTooShort(9), resourceUnavailable(10), divideByZero(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "The error that occurred. In the following explanations the expected timing of the error is in parentheses. 'S' means the error occurs on a Set request. 'E' means the error occurs on the attempt to evaluate the expression either due to Get from expValueTable or in ongoing delta processing. invalidSyntax the value sent for expExpression is not valid Expression MIB expression syntax (S) undefinedObjectIndex an object reference ($n) in expExpression does not have a matching instance in expObjectTable (E) unrecognizedOperator the value sent for expExpression held an unrecognized operator (S) unrecognizedFunction the value sent for expExpression held an unrecognized function name (S) invalidOperandType an operand in expExpression is not the right type for the associated operator or result (SE) unmatchedParenthesis the value sent for expExpression is not correctly parenthesized (S) tooManyWildcardValues evaluating the expression exceeded the limit set by expResourceDelta WildcardInstanceMaximum (E) recursion through some chain of embedded expressions the expression invokes itself (E) deltaTooShort the delta for the next evaluation passed before the system could evaluate the present sample (E) resourceUnavailable some resource, typically dynamic memory, was unavailable (SE) divideByZero an attempt to divide by zero occurred (E) For the errors that occur when the attempt is made to set expExpression Set request fails with the SNMP error code 'wrongValue'. Such failures refer to the most recent failure to Set expExpression, not to the present value of expExpression which must be either unset or syntactically correct. Errors that occur during evalutaion for a Get* operation return the SNMP error code 'genErr' except for 'tooManyWildcardValues' and 'resourceUnavailable' which return the SNMP error code 'resourceUnavailable'. This object is not instantiated if there have been no errors." ::= { expExpressionEntry 10 } expExpressionInstance OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "The expValueInstance being evaluated when the error occurred. A zero-length indicates irrelevance. This object is not instantiated if there have been no errors." ::= { expExpressionEntry 11 } expExpressionOwner OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." DEFVAL { "" } ::= { expExpressionEntry 12 } -- Object Table expObjectTable OBJECT-TYPE SYNTAX SEQUENCE OF ExpObjectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of object definitions for each expExpression. Wildcarding instance IDs: It is legal to omit all or part of the instance portion for some or all of the objects in an expression. (See the DESCRIPTION of expObjectID for details. However, note that if more than one object in the same expression is wildcarded in this way, they all must be objects where that portion of the instance is the same. In other words, all objects may be in the same SEQUENCE or in different SEQUENCEs but with the same semantic index value (e.g., a value of ifIndex) for the wildcarded portion." ::= { expDefine 2 } expObjectEntry OBJECT-TYPE SYNTAX ExpObjectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an object. An application uses expObjectStatus to create entries in this table while in the process of defining an expression. Values of read-create objects in this table may be changed at any time." INDEX { expExpressionIndex, expObjectIndex } ::= { expObjectTable 1 } ExpObjectEntry ::= SEQUENCE { expObjectIndex Unsigned32, expObjectID OBJECT IDENTIFIER, expObjectIDWildcard TruthValue, expObjectSampleType INTEGER, expObjectDeltaDiscontinuityID OBJECT IDENTIFIER, expObjectDiscontinuityIDWildcard TruthValue, expObjectDiscontinuityIDType INTEGER, expObjectConditional OBJECT IDENTIFIER, expObjectConditionalWildcard TruthValue, expObjectStatus RowStatus } expObjectIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Within an expression, a unique, numeric identification for an object. Prefixed with a dollar sign ('$') this is used to reference the object in the corresponding expExpression." ::= { expObjectEntry 1 } expObjectID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The OBJECT IDENTIFIER (OID) of this object. The OID may be fully qualified, meaning it includes a complete instance identifier part (e.g., ifInOctets.1 or sysUpTime.0), or it may not be fully qualified, meaning it may lack all or part of the instance identifier. If the expObjectID is not fully qualified, then expObjectWildcard must be set to true(1). The value of the expression will be multiple values, as if done for a GetNext sweep of the object. An object here may itself be the result of an expression but recursion is not allowed. NOTE: The simplest implementations of this MIB may not allow wildcards." ::= { expObjectEntry 2 } expObjectIDWildcard OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "A true value indicates the expObjecID of this row is a wildcard object. False indicates that expObjectID is fully instanced. If all expObjectWildcard values for a given expression are FALSE, expExpressionPrefix will reflect a scalar object (ie will be 0.0). NOTE: The simplest implementations of this MIB may not allow wildcards." DEFVAL { false } ::= { expObjectEntry 3 } expObjectSampleType OBJECT-TYPE SYNTAX INTEGER { absoluteValue(1), deltaValue(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The method of sampling the selected variable. An 'absoluteValue' is simply the present value of the object. A 'deltaValue' is the present value minus the previous value, which was sampled expExpressionDeltaInterval seconds ago. This is intended primarily for use with SNMP counters, which are meaningless as an 'absoluteValue', but may be used with any integer-based value. When an expression contains both delta and absolute values the absolute values are obtained at the end of the delta period." DEFVAL { absoluteValue } ::= { expObjectEntry 4 } sysUpTimeInstance OBJECT IDENTIFIER ::= { sysUpTime 0 } expObjectDeltaDiscontinuityID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The OBJECT IDENTIFIER (OID) of a TimeTicks or TimeStamp object that indicates a discontinuity in the value at expObjectID. This object is not instantiated if expObject is not 'deltaValue'. The OID may be for a leaf object (e.g. sysUpTime.0) or may be wildcarded to match expObjectID. This object supports normal checking for a discontinuity in a counter. Note that if this object does not point to sysUpTime discontinuity checking must still check sysUpTime for an overall discontinuity. If the object identified is not accessible no discontinuity check will be made." DEFVAL { sysUpTimeInstance } ::= { expObjectEntry 5 } expObjectDiscontinuityIDWildcard OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "A true value indicates the expObjectDeltaDiscontinuityID of this row is a wildcard object. False indicates that expObjectDeltaDiscontinuityID is fully instanced. This object is not instantiated if expObject is not 'deltaValue'. NOTE: The simplest implementations of this MIB may not allow wildcards." DEFVAL { false } ::= { expObjectEntry 6 } expObjectDiscontinuityIDType OBJECT-TYPE SYNTAX INTEGER { timeTicks(1), timeStamp(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The value 'timeTicks' indicates the expObjectDeltaDiscontinuityID of this row is of syntax TimeTicks. The value 'timeStamp' indicates that expObjectDeltaDiscontinuityID is of syntax TimeStamp. This object is not instantiated if expObject is not 'deltaValue'." DEFVAL { timeTicks } ::= { expObjectEntry 7 } expObjectConditional OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The OBJECT IDENTIFIER (OID) of an object that overrides whether the instance of expObjectID is to be considered usable. If the value of the object at expObjectConditional is 0 or not instantiated, the object at expObjectID is treated as if it is not instantiated. In other words, expObjectConditional is a filter that controls whether or not to use the value at expObjectID. The OID may be for a leaf object (e.g. sysObjectID.0) or may be wildcarded to match expObjectID. If expObject is wildcarded and expObjectID in the same row is not, the wild portion of expObjectConditional must match the wildcarding of the rest of the expression. If no object in the expression is wildcarded but expObjectConditional is, use the lexically first instance (if any) of expObjectConditional. If the value of expObjectConditional is 0.0 operation is as if the value pointed to by expObjectConditional is a non-zero (true) value. Note that expObjectConditional can not trivially use an object of syntax TruthValue, since the underlying value is not 0 or 1." DEFVAL { zeroDotZero } ::= { expObjectEntry 8 } expObjectConditionalWildcard OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "A true value indicates the expObjectConditional of this row is a wildcard object. False indicates that expObjectConditional is fully instanced. NOTE: The simplest implementations of this MIB may not allow wildcards." DEFVAL { false } ::= { expObjectEntry 9 } expObjectStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The control that allows creation/deletion of entries. Objects in this table may be changed while expObjectStatus is in any state." ::= { expObjectEntry 10 } -- Expression Value Table expValueTable OBJECT-TYPE SYNTAX SEQUENCE OF ExpValueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of values from evaluated expressions." ::= { expValue 1 } expValueEntry OBJECT-TYPE SYNTAX ExpValueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single value from an evaluated expression. For a given instance, only one 'Val' object in the conceptual row will be instantiated, that is, the one with the appropriate type for the value. For values that contain no objects of expObjectSampleType 'deltaValue', reading a value from the table causes the evaluation of the expression for that value. For those that contain a 'deltaValue' the value read is as of the last delta interval. If in the attempt to evaluate the expression one or more of the necessary objects is not available, the corresponding entry in this table is effectively not instantiated. To maintain security of MIB information, expression evaluation must take place using security credentials for the implied Gets of the objects in the expression. For expressions with no deltaValue those security credentials are the ones that came with the Get* for the value. For expressions with a deltaValue the ongoing expression evaluation is under the security credentials of the creator of the corresponding expNameEntry." INDEX { expExpressionIndex, expValueInstance } ::= { expValueTable 1 } ExpValueEntry ::= SEQUENCE { expValueInstance OBJECT IDENTIFIER, expValueCounter32Val Counter32, expValueUnsigned32Val Unsigned32, expValueInteger32Val Integer32, expValueIpAddressVal IpAddress, expValueOctetStringVal OCTET STRING, expValueOidVal OBJECT IDENTIFIER, expValueCounter64Val Counter64 } expValueInstance OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The final instance portion of a value's OID according to the wildcarding in instances of expObjectID for the expression. The prefix of this OID fragment is 0.0, leading to the following behavior. If there is no wildcarding, the value is 0.0.0. In other words, there is one value which standing alone would have been a scalar with a 0 at the end of its OID. If there is wildcarding, the value is 0.0 followed by a value that the wildcard can take, thus defining one value instance for each real, possible value of the wildcard. So, for example, if the wildcard worked out to be an ifIndex, there is an expValueInstance for each applicable ifIndex." ::= { expValueEntry 1 } expValueCounter32Val OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value when expExpressionValueType is 'counter32'." ::= { expValueEntry 2 } expValueUnsigned32Val OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value when expExpressionValueType is 'unsignedOrGauge32' or 'timeTicks'." ::= { expValueEntry 3 } expValueInteger32Val OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value when expExpressionValueType is 'integer32'." ::= { expValueEntry 4 } expValueIpAddressVal OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The value when expExpressionValueType is 'ipAddress'." ::= { expValueEntry 5 } expValueOctetStringVal OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value when expExpressionValueType is 'octetString'." ::= { expValueEntry 6 } expValueOidVal OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "The value when expExpressionValueType is 'objectId'." ::= { expValueEntry 7 } expValueCounter64Val OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The value when expExpressionValueType is 'counter64'." ::= { expValueEntry 8 } -- Conformance expressionMIBConformance OBJECT IDENTIFIER ::= { expressionMIB 3 } expressionMIBCompliances OBJECT IDENTIFIER ::= { expressionMIBConformance 1 } expressionMIBGroups OBJECT IDENTIFIER ::= { expressionMIBConformance 2 } -- Compliance expressionMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Expression MIB." MODULE -- this module MANDATORY-GROUPS { expressionResourceGroup, expressionDefinitionGroup, expressionValueGroup } OBJECT expResourceDeltaMinimum SYNTAX Integer32 (-1 | 60..600) DESCRIPTION "Implementation need not allow deltas or it may implement them and restrict them to higher values." OBJECT expObjectSampleType WRITE-SYNTAX INTEGER { absoluteValue(1) } DESCRIPTION "Implementation need not allow deltas." ::= { expressionMIBCompliances 1 } -- Units of Conformance expressionResourceGroup OBJECT-GROUP OBJECTS { expResourceDeltaMinimum, expResourceDeltaWildcardInstanceMaximum, expResourceDeltaWildcardInstances, expResourceDeltaWildcardInstancesHigh, expResourceDeltaWildcardInstanceResourceLacks } STATUS current DESCRIPTION "Expression definition resource management." ::= { expressionMIBGroups 1 } expressionDefinitionGroup OBJECT-GROUP OBJECTS { expNameLastChange, expNameHighestIndex, expExpressionIndex, expNameStatus, expExpressionName, expExpression, expExpressionValueType, expExpressionComment, expExpressionDeltaInterval, expExpressionPrefix, expExpressionErrors, expExpressionErrorTime, expExpressionErrorIndex, expExpressionError, expExpressionInstance, expExpressionOwner, expObjectID, expObjectIDWildcard, expObjectSampleType, expObjectDeltaDiscontinuityID, expObjectDiscontinuityIDWildcard, expObjectDiscontinuityIDType, expObjectConditional, expObjectConditionalWildcard, expObjectStatus } STATUS current DESCRIPTION "Expression definition resource management." ::= { expressionMIBGroups 2 } expressionValueGroup OBJECT-GROUP OBJECTS { expValueCounter32Val, expValueUnsigned32Val, expValueInteger32Val, expValueIpAddressVal, expValueOctetStringVal, expValueOidVal, expValueCounter64Val } STATUS current DESCRIPTION "Expression definition resource management." ::= { expressionMIBGroups 3 } END