-- ***************************************************************** -- SONET-MIB.my : Sonet MIB file -- -- Mar 2001 -- -- Copyright (c) 2001, 2004 by cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** -- This mib was extracted from RFC 3592 SONET-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, transmission FROM SNMPv2-SMI DisplayString, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB; -- This is the MIB module for the SONET/SDH Interface objects. sonetMIB MODULE-IDENTITY LAST-UPDATED "200308110000Z" ORGANIZATION "IETF AToM MIB Working Group" CONTACT-INFO "WG charter: http://www.ietf.org/html.charters/atommib-charter.html Mailing Lists: General Discussion: atommib@research.telcordia.com To Subscribe: atommib-request@research.telcordia.com Kaj Tesink Telcordia Technologies Tel: (732) 758-5254 Fax: (732) 758-2269 E-mail: kaj@research.telcordia.com." DESCRIPTION "The MIB module to describe SONET/SDH interface objects. Copyright (C) The Internet Society (2003). This version of this MIB module is part of RFC 3592; see the RFC itself for full legal notices." REVISION "200308110000Z" DESCRIPTION "The key changes made to this MIB module since its publication in RFC 2558 are as follows. (1) Corrected typographical error (bellcore1991(2) in sonetSESthresholdSet) (2) Added support for sts192cSTM64(6) and sts768cSTM256(7) in sonetPathCurrentWidth (3) Corrected description of the applicability of VTs for SDH for improved accuracy (4) Added clarification in the SES description that CV counts should be frozen during SESs (5) Corrected typographical errors: - Line Alarm Indication Signal description of the Terminology section (20.5 --> 2.5 seconds) - In the Terminology section sonetSESThresholdSet --> sonetSESthresholdSet " REVISION "199810190000Z" DESCRIPTION "The RFC 2558 version of this MIB module. The key changes made to this MIB module since its initial publication in RFC 1595 are as follows. (1) The MODULE-IDENTITY has been updated to reflect the changes to the MIB. (2) Where applicable, the textual conventions PerfCurrentCount and PerfIntervalCount from PerfHist-TC-MIB have been used in place of Gauge32. (3) An agent now has the option to delay updates to the various performance counts in lieu of performing retroactive adjustments upon entering into or exiting from unavailable time. This implementation option is described in Appendix A of this memo. (4) In order to make the SONET-MIB more useful for circuit provisioning, the formerly read-only objects sonetMediumType, sonetMediumLineCoding, sonetMediumLineType, and sonetMediumCircuitIdentifier have been given a MAX-ACCESS of read-write. The MIN-ACCESS remains read-only. (5) The DESCRIPTION clause for sonetMediumTimeElapsed has been updated to describe its behaviour if the duration of the current interval exceeds the maximum value. (6) The DESCRIPTION clause for sonetMediumValidIntervals has been updated to describe its behaviour when some intervals may be unavailable, and the object sonetMediumInvalidIntervals has been added to keep count of the number of missing intervals (if any). (7) The object sonetMediumLoopbackConfig has been added to enable or disable loopback configurations. (8) Because the error count thresholds for declaring severely errored seconds that are specified in ANSI T1.231-1993, ITU-T G.826-1995, and ANSI T1.231-1997 are all different from each other and from the thresholds specified in RFC 1595, an enumerated INTEGER object sonetSESthresholdSet has been added to allow an agent to specify which threshold set is in use. Text has been added to Section 3 stating that if this object is not implemented the thresholds specified in RFC 1595 should be assumed, and the table containing those thresholds has been moved to Appendix B of this memo. (9) A column with SYNTAX TruthValue has been added to each interval table. The purpose of the additional column is to indicate, for each interval, whether the data is valid in the sense intended by ANSI T1.231 clause 9.1.2.2 [T1.231a][T1.231b]. The objects in question are: sonetSectionIntervalValidData sonetLineIntervalValidData sonetFarEndLineIntervalValidData sonetPathIntervalValidData sonetFarEndPathIntervalValidData sonetVTIntervalValidData sonetFarEndVTIntervalValidData (10) The ranges for sonetPathCurrentStatus and sonetVTCurrentStatus have been made consistent with the DESCRIPTION clauses. (11) The conformance information has been updated. Previous conformance information from RFC 1595 has been deprecated. Some typographical errors in the deprecated section have been corrected in order to prevent MIB compilation errors." REVISION "199401030000Z" DESCRIPTION "The RFC 1595 version of this MIB module." ::= { transmission 39 } -- This is the MIB module for the SONET/SDH objects sonetObjects OBJECT IDENTIFIER ::= { sonetMIB 1 } sonetObjectsPath OBJECT IDENTIFIER ::= { sonetMIB 2 } sonetObjectsVT OBJECT IDENTIFIER ::= { sonetMIB 3 } -- groups in the SONET/SDH MIB module sonetMedium OBJECT IDENTIFIER ::= { sonetObjects 1 } sonetSection OBJECT IDENTIFIER ::= { sonetObjects 2 } sonetLine OBJECT IDENTIFIER ::= { sonetObjects 3 } sonetFarEndLine OBJECT IDENTIFIER ::= { sonetObjects 4 } sonetPath OBJECT IDENTIFIER ::= { sonetObjectsPath 1 } sonetFarEndPath OBJECT IDENTIFIER ::= { sonetObjectsPath 2 } sonetVT OBJECT IDENTIFIER ::= { sonetObjectsVT 1 } sonetFarEndVT OBJECT IDENTIFIER ::= { sonetObjectsVT 2 } -- the SONET/SDH Medium group -- SONET/SDH interfaces for some applications may be electrical -- interfaces and not optical interfaces. This group handles -- the configuration information for both optical SONET/SDH -- interfaces and electrical SONET/SDH interfaces. sonetMediumTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetMediumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Medium table." ::= { sonetMedium 1 } sonetMediumEntry OBJECT-TYPE SYNTAX SonetMediumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Medium table." INDEX { ifIndex } ::= { sonetMediumTable 1 } SonetMediumEntry ::= SEQUENCE { sonetMediumType INTEGER, sonetMediumTimeElapsed Integer32, sonetMediumValidIntervals Integer32, sonetMediumLineCoding INTEGER, sonetMediumLineType INTEGER, sonetMediumCircuitIdentifier DisplayString, sonetMediumInvalidIntervals Integer32, sonetMediumLoopbackConfig BITS } sonetMediumType OBJECT-TYPE SYNTAX INTEGER { sonet(1), sdh(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable identifies whether a SONET or a SDH signal is used across this interface." ::= { sonetMediumEntry 1 } sonetMediumTimeElapsed OBJECT-TYPE SYNTAX Integer32 (1..900) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value." ::= { sonetMediumEntry 2 } sonetMediumValidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals for which data was collected. A SONET/SDH interface must be capable of supporting at least n intervals. The minimum value of n is 4. The default of n is 32. The maximum value of n is 96. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available. " ::= { sonetMediumEntry 3 } sonetMediumLineCoding OBJECT-TYPE SYNTAX INTEGER { sonetMediumOther(1), sonetMediumB3ZS(2), sonetMediumCMI(3), sonetMediumNRZ(4), sonetMediumRZ(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable describes the line coding for this interface. The B3ZS and CMI are used for electrical SONET/SDH signals (STS-1 and STS-3). The Non-Return to Zero (NRZ) and the Return to Zero are used for optical SONET/SDH signals." ::= { sonetMediumEntry 4 } sonetMediumLineType OBJECT-TYPE SYNTAX INTEGER { sonetOther(1), sonetShortSingleMode(2), sonetLongSingleMode(3), sonetMultiMode(4), sonetCoax(5), sonetUTP(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable describes the line type for this interface. The line types are Short and Long Range Single Mode fiber or Multi-Mode fiber interfaces, and coax and UTP for electrical interfaces. The value sonetOther should be used when the Line Type is not one of the listed values." ::= { sonetMediumEntry 5 } sonetMediumCircuitIdentifier OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. Note that the circuit identifier, if available, is also represented by ifPhysAddress." ::= { sonetMediumEntry 6 } sonetMediumInvalidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals in the range from 0 to sonetMediumValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { sonetMediumEntry 7 } sonetMediumLoopbackConfig OBJECT-TYPE SYNTAX BITS { sonetNoLoop(0), sonetFacilityLoop(1), sonetTerminalLoop(2), sonetOtherLoop(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current loopback state of the SONET/SDH interface. The values mean: sonetNoLoop Not in the loopback state. A device that is not capable of performing a loopback on this interface shall always return this value. sonetFacilityLoop The received signal at this interface is looped back out through the corresponding transmitter in the return direction. sonetTerminalLoop The signal that is about to be transmitted is connected to the associated incoming receiver. sonetOtherLoop Loopbacks that are not defined here." ::= { sonetMediumEntry 8 } sonetSESthresholdSet OBJECT-TYPE SYNTAX INTEGER { other(1), bellcore1991(2), ansi1993(3), itu1995(4), ansi1997(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "An enumerated integer indicating which recognized set of SES thresholds that the agent uses for determining severely errored seconds and unavailable time. other(1) None of the following. bellcore1991(2) Bellcore TR-NWT-000253, 1991 [TR253], or ANSI T1M1.3/93-005R2, 1993 [T1M1.3]. See also Appendix B. ansi1993(3) ANSI T1.231, 1993 [T1.231a], or Bellcore GR-253-CORE, Issue 2, 1995 [GR253] itu1995(4) ITU Recommendation G.826, 1995 [G.826] ansi1997(5) ANSI T1.231, 1997 [T1.231b] If a manager changes the value of this object then the SES statistics collected prior to this change must be invalidated." ::= { sonetMedium 2 } -- the SONET/SDH Section group -- this group consists of 2 tables: -- - the SONET/SDH Section Current Table -- - the SONET/SDH Section Interval Table -- the SONET/SDH Section Current Table -- The SONET/SDH Section -- current table contains various statistics -- being collected for the current 15 minute interval. sonetSectionCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSectionCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Section Current table." ::= { sonetSection 1 } sonetSectionCurrentEntry OBJECT-TYPE SYNTAX SonetSectionCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Section Current table." INDEX { ifIndex } ::= { sonetSectionCurrentTable 1 } SonetSectionCurrentEntry ::= SEQUENCE { sonetSectionCurrentStatus Integer32, sonetSectionCurrentESs PerfCurrentCount, sonetSectionCurrentSESs PerfCurrentCount, sonetSectionCurrentSEFSs PerfCurrentCount, sonetSectionCurrentCVs PerfCurrentCount } sonetSectionCurrentStatus OBJECT-TYPE SYNTAX Integer32 (1..6) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the status of the interface. The sonetSectionCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetSectionNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetSectionNoDefect 2 sonetSectionLOS 4 sonetSectionLOF" ::= { sonetSectionCurrentEntry 1 } sonetSectionCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered by a SONET/SDH Section in the current 15 minute interval." ::= { sonetSectionCurrentEntry 2 } sonetSectionCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Section in the current 15 minute interval." ::= { sonetSectionCurrentEntry 3 } sonetSectionCurrentSEFSs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Framing Seconds encountered by a SONET/SDH Section in the current 15 minute interval." ::= { sonetSectionCurrentEntry 4 } sonetSectionCurrentCVs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Coding Violations encountered by a SONET/SDH Section in the current 15 minute interval." ::= { sonetSectionCurrentEntry 5 } -- the SONET/SDH Section Interval Table -- The SONET/SDH Section Interval Table -- contains various statistics -- collected by each system over a maximum -- of the previous 24 hours of -- operation. The past 24 hours may be broken into 96 -- completed 15 minute intervals. -- A system is required to store at -- least 4 completed 15 minute interval. -- The default value is 32 intervals. sonetSectionIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSectionIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Section Interval table." ::= { sonetSection 2 } sonetSectionIntervalEntry OBJECT-TYPE SYNTAX SonetSectionIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Section Interval table." INDEX { ifIndex, sonetSectionIntervalNumber } ::= { sonetSectionIntervalTable 1 } SonetSectionIntervalEntry ::= SEQUENCE { sonetSectionIntervalNumber Integer32, sonetSectionIntervalESs PerfIntervalCount, sonetSectionIntervalSESs PerfIntervalCount, sonetSectionIntervalSEFSs PerfIntervalCount, sonetSectionIntervalCVs PerfIntervalCount, sonetSectionIntervalValidData TruthValue } sonetSectionIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { sonetSectionIntervalEntry 1 } sonetSectionIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours." ::= { sonetSectionIntervalEntry 2 } sonetSectionIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours." ::= { sonetSectionIntervalEntry 3 } sonetSectionIntervalSEFSs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Framing Seconds encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours." ::= { sonetSectionIntervalEntry 4 } sonetSectionIntervalCVs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Coding Violations encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours." ::= { sonetSectionIntervalEntry 5 } sonetSectionIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { sonetSectionIntervalEntry 6 } -- the SONET/SDH Line group -- this group consists of 2 tables: -- - the SONET/SDH Line Current Table -- - the SONET/SDH Line Interval Table -- the SONET/SDH Line Current Table -- The SONET/SDH Line -- current table contains various statistics -- being collected for the current 15 minute interval. sonetLineCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetLineCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Line Current table." ::= { sonetLine 1 } sonetLineCurrentEntry OBJECT-TYPE SYNTAX SonetLineCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Line Current table." INDEX { ifIndex } ::= { sonetLineCurrentTable 1 } SonetLineCurrentEntry ::= SEQUENCE { sonetLineCurrentStatus Integer32, sonetLineCurrentESs PerfCurrentCount, sonetLineCurrentSESs PerfCurrentCount, sonetLineCurrentCVs PerfCurrentCount, sonetLineCurrentUASs PerfCurrentCount } sonetLineCurrentStatus OBJECT-TYPE SYNTAX Integer32 (1..6) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the status of the interface. The sonetLineCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetLineNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetLineNoDefect 2 sonetLineAIS 4 sonetLineRDI" ::= { sonetLineCurrentEntry 1 } sonetLineCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered by a SONET/SDH Line in the current 15 minute interval." ::= { sonetLineCurrentEntry 2 } sonetLineCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Line in the current 15 minute interval." ::= { sonetLineCurrentEntry 3 } sonetLineCurrentCVs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Coding Violations encountered by a SONET/SDH Line in the current 15 minute interval." ::= { sonetLineCurrentEntry 4 } sonetLineCurrentUASs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered by a SONET/SDH Line in the current 15 minute interval." ::= { sonetLineCurrentEntry 5 } -- the SONET/SDH Line Interval Table -- The SONET/SDH Line Interval Table -- contains various statistics -- collected by each system over a maximum -- of the previous 24 hours of -- operation. The past 24 hours may be broken into 96 -- completed 15 minute intervals. -- A system is required to store at -- least 4 completed 15 minute interval. -- The default value is 32 intervals. sonetLineIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetLineIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Line Interval table." ::= { sonetLine 2 } sonetLineIntervalEntry OBJECT-TYPE SYNTAX SonetLineIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Line Interval table." INDEX { ifIndex, sonetLineIntervalNumber } ::= { sonetLineIntervalTable 1 } SonetLineIntervalEntry ::= SEQUENCE { sonetLineIntervalNumber Integer32, sonetLineIntervalESs PerfIntervalCount, sonetLineIntervalSESs PerfIntervalCount, sonetLineIntervalCVs PerfIntervalCount, sonetLineIntervalUASs PerfIntervalCount, sonetLineIntervalValidData TruthValue } sonetLineIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { sonetLineIntervalEntry 1 } sonetLineIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours." ::= { sonetLineIntervalEntry 2 } sonetLineIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours." ::= { sonetLineIntervalEntry 3 } sonetLineIntervalCVs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Coding Violations encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours." ::= { sonetLineIntervalEntry 4 } sonetLineIntervalUASs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours." ::= { sonetLineIntervalEntry 5 } sonetLineIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { sonetLineIntervalEntry 6 } -- The SONET/SDH Far End Line group. -- This group may only be implemented by SONET/SDH (LTEs) -- systems that provide for a far end block error (FEBE) -- information at the SONET/SDH Line Layer. -- This group consists of two tables: -- SONET/SDH Far End Line Current Table -- SONET/SDH Far End Line Interval Table -- The SONET/SDH Far End Line Current Table -- The SONET/SDH Far End Line Current table contains -- various statistics being -- collected for the current 15 minute interval. -- The statistics are collected from the far end -- block error code (FEBE) -- within the third Z2 byte of the Line Overhead -- in Broadband ISDN applications. -- The definitions are the same as described for -- the near-end information. sonetFarEndLineCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetFarEndLineCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Far End Line Current table." ::= { sonetFarEndLine 1 } sonetFarEndLineCurrentEntry OBJECT-TYPE SYNTAX SonetFarEndLineCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Far End Line Current table." INDEX { ifIndex } ::= { sonetFarEndLineCurrentTable 1 } SonetFarEndLineCurrentEntry ::= SEQUENCE { sonetFarEndLineCurrentESs PerfCurrentCount, sonetFarEndLineCurrentSESs PerfCurrentCount, sonetFarEndLineCurrentCVs PerfCurrentCount, sonetFarEndLineCurrentUASs PerfCurrentCount } sonetFarEndLineCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH interface in the current 15 minute interval." ::= { sonetFarEndLineCurrentEntry 1 } sonetFarEndLineCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Medium/Section/Line interface in the current 15 minute interval." ::= { sonetFarEndLineCurrentEntry 2 } sonetFarEndLineCurrentCVs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Medium/Section/Line interface in the current 15 minute interval." ::= { sonetFarEndLineCurrentEntry 3 } sonetFarEndLineCurrentUASs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Medium/Section/Line interface in the current 15 minute interval." ::= { sonetFarEndLineCurrentEntry 4 } -- The SONET/SDH Far End Line Interval Table -- The SONET/SDH Far End Line Interval Table -- contains various statistics -- collected by each system over a maximum -- of the previous 24 hours of -- operation. The past 24 hours may be broken into 96 -- completed 15 minute intervals. -- A system is required to store at -- least 4 completed 15 minute interval. -- The default value is 32 intervals. sonetFarEndLineIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetFarEndLineIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Far End Line Interval table." ::= { sonetFarEndLine 2 } sonetFarEndLineIntervalEntry OBJECT-TYPE SYNTAX SonetFarEndLineIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Far End Line Interval table." INDEX { ifIndex, sonetFarEndLineIntervalNumber } ::= { sonetFarEndLineIntervalTable 1 } SonetFarEndLineIntervalEntry ::= SEQUENCE { sonetFarEndLineIntervalNumber Integer32, sonetFarEndLineIntervalESs PerfIntervalCount, sonetFarEndLineIntervalSESs PerfIntervalCount, sonetFarEndLineIntervalCVs PerfIntervalCount, sonetFarEndLineIntervalUASs PerfIntervalCount, sonetFarEndLineIntervalValidData TruthValue } sonetFarEndLineIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { sonetFarEndLineIntervalEntry 1 } sonetFarEndLineIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndLineIntervalEntry 2 } sonetFarEndLineIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndLineIntervalEntry 3 } sonetFarEndLineIntervalCVs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndLineIntervalEntry 4 } sonetFarEndLineIntervalUASs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndLineIntervalEntry 5 } sonetFarEndLineIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { sonetFarEndLineIntervalEntry 6 } -- the SONET/SDH Path group -- this group consists of 2 tables: -- - the SONET/SDH Path Current Table -- - the SONET/SDH Path Interval Table -- the SONET/SDH Path Current Table -- The SONET/SDH Path -- current table contains various statistics -- being collected for the current 15 minute interval. sonetPathCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetPathCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Path Current table." ::= { sonetPath 1 } sonetPathCurrentEntry OBJECT-TYPE SYNTAX SonetPathCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Path Current table." INDEX { ifIndex } ::= { sonetPathCurrentTable 1 } SonetPathCurrentEntry ::= SEQUENCE { sonetPathCurrentWidth INTEGER, sonetPathCurrentStatus Integer32, sonetPathCurrentESs PerfCurrentCount, sonetPathCurrentSESs PerfCurrentCount, sonetPathCurrentCVs PerfCurrentCount, sonetPathCurrentUASs PerfCurrentCount } sonetPathCurrentWidth OBJECT-TYPE SYNTAX INTEGER { sts1(1), sts3cSTM1(2), sts12cSTM4(3), sts24c(4), sts48cSTM16(5), sts192cSTM64(6), sts768cSTM256(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "A value that indicates the type of the SONET/SDH Path. For SONET, the assigned types are the STS-Nc SPEs, where N = 1, 3, 12, 24, 48, 192 and 768. STS-1 is equal to 51.84 Mbps. For SDH, the assigned types are the STM-Nc VCs, where N = 1, 4, 16, 64 and 256." ::= { sonetPathCurrentEntry 1 } sonetPathCurrentStatus OBJECT-TYPE SYNTAX Integer32 (1..62) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the status of the interface. The sonetPathCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetPathNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetPathNoDefect 2 sonetPathSTSLOP 4 sonetPathSTSAIS 8 sonetPathSTSRDI 16 sonetPathUnequipped 32 sonetPathSignalLabelMismatch" ::= { sonetPathCurrentEntry 2 } sonetPathCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered by a SONET/SDH Path in the current 15 minute interval." ::= { sonetPathCurrentEntry 3 } sonetPathCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Path in the current 15 minute interval." ::= { sonetPathCurrentEntry 4 } sonetPathCurrentCVs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Coding Violations encountered by a SONET/SDH Path in the current 15 minute interval." ::= { sonetPathCurrentEntry 5 } sonetPathCurrentUASs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered by a Path in the current 15 minute interval." ::= { sonetPathCurrentEntry 6 } -- the SONET/SDH Path Interval Table -- The SONET/SDH Path Interval Table -- contains various statistics -- collected by each system over a maximum -- of the previous 24 hours of -- operation. The past 24 hours may be broken into 96 -- completed 15 minute intervals. -- A system is required to store at -- least 4 completed 15 minute interval. -- The default value is 32 intervals. sonetPathIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetPathIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Path Interval table." ::= { sonetPath 2 } sonetPathIntervalEntry OBJECT-TYPE SYNTAX SonetPathIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Path Interval table." INDEX { ifIndex, sonetPathIntervalNumber } ::= { sonetPathIntervalTable 1 } SonetPathIntervalEntry ::= SEQUENCE { sonetPathIntervalNumber Integer32, sonetPathIntervalESs PerfIntervalCount, sonetPathIntervalSESs PerfIntervalCount, sonetPathIntervalCVs PerfIntervalCount, sonetPathIntervalUASs PerfIntervalCount, sonetPathIntervalValidData TruthValue } sonetPathIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { sonetPathIntervalEntry 1 } sonetPathIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours." ::= { sonetPathIntervalEntry 2 } sonetPathIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours." ::= { sonetPathIntervalEntry 3 } sonetPathIntervalCVs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Coding Violations encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours." ::= { sonetPathIntervalEntry 4 } sonetPathIntervalUASs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered by a Path in a particular 15-minute interval in the past 24 hours." ::= { sonetPathIntervalEntry 5 } sonetPathIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { sonetPathIntervalEntry 6 } -- The SONET/SDH Far End Path group -- This group consists of two tables: -- - SONET/SDH Far End Path Current Table -- - SONET/SDH Far End Path Interval Table -- The SONET/SDH Far End Path Current Table -- The SONET/SDH Far End Path Current table -- contains various statistics -- being collected for the current 15 minute interval. -- The statistics are collected from -- the far end block error code -- (FEBE) within the G1 byte of the Path Overhead. -- The definitions are the same as described for -- the near-end information. sonetFarEndPathCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetFarEndPathCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Far End Path Current table." ::= { sonetFarEndPath 1 } sonetFarEndPathCurrentEntry OBJECT-TYPE SYNTAX SonetFarEndPathCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Far End Path Current table." INDEX { ifIndex } ::= { sonetFarEndPathCurrentTable 1 } SonetFarEndPathCurrentEntry ::= SEQUENCE { sonetFarEndPathCurrentESs PerfCurrentCount, sonetFarEndPathCurrentSESs PerfCurrentCount, sonetFarEndPathCurrentCVs PerfCurrentCount, sonetFarEndPathCurrentUASs PerfCurrentCount } sonetFarEndPathCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH interface in the current 15 minute interval." ::= { sonetFarEndPathCurrentEntry 1 } sonetFarEndPathCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Path interface in the current 15 minute interval." ::= { sonetFarEndPathCurrentEntry 2 } sonetFarEndPathCurrentCVs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Path interface in the current 15 minute interval." ::= { sonetFarEndPathCurrentEntry 3 } sonetFarEndPathCurrentUASs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Path interface in the current 15 minute interval." ::= { sonetFarEndPathCurrentEntry 4 } -- The SONET/SDH Far End Path Interval Table -- The SONET/SDH Far End Path Interval Table -- contains various statistics -- collected by each system over a maximum -- of the previous 24 hours of -- operation. The past 24 hours may be broken into 96 -- completed 15 minute intervals. -- A system is required to store at -- least 4 completed 15 minute interval. -- The default value is 32 intervals. sonetFarEndPathIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetFarEndPathIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Far End Path Interval table." ::= { sonetFarEndPath 2 } sonetFarEndPathIntervalEntry OBJECT-TYPE SYNTAX SonetFarEndPathIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Far End Path Interval table." INDEX { ifIndex, sonetFarEndPathIntervalNumber } ::= { sonetFarEndPathIntervalTable 1 } SonetFarEndPathIntervalEntry ::= SEQUENCE { sonetFarEndPathIntervalNumber Integer32, sonetFarEndPathIntervalESs PerfIntervalCount, sonetFarEndPathIntervalSESs PerfIntervalCount, sonetFarEndPathIntervalCVs PerfIntervalCount, sonetFarEndPathIntervalUASs PerfIntervalCount, sonetFarEndPathIntervalValidData TruthValue } sonetFarEndPathIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { sonetFarEndPathIntervalEntry 1 } sonetFarEndPathIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndPathIntervalEntry 2 } sonetFarEndPathIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndPathIntervalEntry 3 } sonetFarEndPathIntervalCVs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndPathIntervalEntry 4 } sonetFarEndPathIntervalUASs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndPathIntervalEntry 5 } sonetFarEndPathIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { sonetFarEndPathIntervalEntry 6 } -- the SONET/SDH Virtual Tributary group -- this group consists of 2 tables: -- - the SONET/SDH VT Current Table -- - the SONET/SDH VT Interval Table -- Corresponding SDH signals for SONET VTs are -- as follows: -- A VT1.5 = TU11 -- A VT2 = TU12 -- A VT3 = none -- none = TU3 -- A VT6 = TU2 -- the SONET/SDH VT Current Table -- The SONET/SDH VT current table -- contains various statistics -- being collected for the -- current 15 minute interval. sonetVTCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetVTCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH VT Current table." ::= { sonetVT 1 } sonetVTCurrentEntry OBJECT-TYPE SYNTAX SonetVTCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH VT Current table." INDEX { ifIndex } ::= { sonetVTCurrentTable 1 } SonetVTCurrentEntry ::= SEQUENCE { sonetVTCurrentWidth INTEGER, sonetVTCurrentStatus Integer32, sonetVTCurrentESs PerfCurrentCount, sonetVTCurrentSESs PerfCurrentCount, sonetVTCurrentCVs PerfCurrentCount, sonetVTCurrentUASs PerfCurrentCount } sonetVTCurrentWidth OBJECT-TYPE SYNTAX INTEGER { vtWidth15VC11(1), vtWidth2VC12(2), vtWidth3(3), vtWidth6VC2(4), vtWidth6c(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "A value that indicates the type of the SONET VT and SDH VC. Assigned widths are VT1.5/VC11, VT2/VC12, VT3, VT6/VC2, and VT6c." ::= { sonetVTCurrentEntry 1 } sonetVTCurrentStatus OBJECT-TYPE SYNTAX Integer32 (1..126) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the status of the interface. The sonetVTCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects and failures simultaneously. The sonetVTNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetVTNoDefect 2 sonetVTLOP 4 sonetVTPathAIS 8 sonetVTPathRDI 16 sonetVTPathRFI 32 sonetVTUnequipped 64 sonetVTSignalLabelMismatch" ::= { sonetVTCurrentEntry 2 } sonetVTCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered by a SONET/SDH VT in the current 15 minute interval." ::= { sonetVTCurrentEntry 3 } sonetVTCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH VT in the current 15 minute interval." ::= { sonetVTCurrentEntry 4 } sonetVTCurrentCVs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Coding Violations encountered by a SONET/SDH VT in the current 15 minute interval." ::= { sonetVTCurrentEntry 5 } sonetVTCurrentUASs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered by a VT in the current 15 minute interval." ::= { sonetVTCurrentEntry 6 } -- the SONET/SDH VT Interval Table -- The SONET/SDH VT Interval Table -- contains various statistics -- collected by each system over a maximum -- of the previous 24 hours of -- operation. The past 24 hours may be broken into 96 -- completed 15 minute intervals. -- A system is required to store at -- least 4 completed 15 minute interval. -- The default value is 32 intervals. sonetVTIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetVTIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH VT Interval table." ::= { sonetVT 2 } sonetVTIntervalEntry OBJECT-TYPE SYNTAX SonetVTIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH VT Interval table." INDEX { ifIndex, sonetVTIntervalNumber } ::= { sonetVTIntervalTable 1 } SonetVTIntervalEntry ::= SEQUENCE { sonetVTIntervalNumber Integer32, sonetVTIntervalESs PerfIntervalCount, sonetVTIntervalSESs PerfIntervalCount, sonetVTIntervalCVs PerfIntervalCount, sonetVTIntervalUASs PerfIntervalCount, sonetVTIntervalValidData TruthValue } sonetVTIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { sonetVTIntervalEntry 1 } sonetVTIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered by a SONET/SDH VT in a particular 15-minute interval in the past 24 hours." ::= { sonetVTIntervalEntry 2 } sonetVTIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH VT in a particular 15-minute interval in the past 24 hours." ::= { sonetVTIntervalEntry 3 } sonetVTIntervalCVs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Coding Violations encountered by a SONET/SDH VT in a particular 15-minute interval in the past 24 hours." ::= { sonetVTIntervalEntry 4 } sonetVTIntervalUASs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered by a VT in a particular 15-minute interval in the past 24 hours." ::= { sonetVTIntervalEntry 5 } sonetVTIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { sonetVTIntervalEntry 6 } -- The SONET/SDH Far End VT group -- This group consists of two tables: -- SONET/SDH Far End VT Current Table -- SONET/SDH Far End VT Interval Table -- The SONET/SDH Far End VT Current -- The SONET/SDH Far End VT Current table -- contains various statistics -- being collected for the current 15 minute interval. -- The statistics are collected from -- the far end block error code -- (FEBE) within the G1 byte of the VT Overhead. -- The definitions are the same as described for -- the near-end information. sonetFarEndVTCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetFarEndVTCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Far End VT Current table." ::= { sonetFarEndVT 1 } sonetFarEndVTCurrentEntry OBJECT-TYPE SYNTAX SonetFarEndVTCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Far End VT Current table." INDEX { ifIndex } ::= { sonetFarEndVTCurrentTable 1 } SonetFarEndVTCurrentEntry ::= SEQUENCE { sonetFarEndVTCurrentESs PerfCurrentCount, sonetFarEndVTCurrentSESs PerfCurrentCount, sonetFarEndVTCurrentCVs PerfCurrentCount, sonetFarEndVTCurrentUASs PerfCurrentCount } sonetFarEndVTCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH interface in the current 15 minute interval." ::= { sonetFarEndVTCurrentEntry 1 } sonetFarEndVTCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH VT interface in the current 15 minute interval." ::= { sonetFarEndVTCurrentEntry 2 } sonetFarEndVTCurrentCVs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH VT interface in the current 15 minute interval." ::= { sonetFarEndVTCurrentEntry 3 } sonetFarEndVTCurrentUASs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH VT interface in the current 15 minute interval." ::= { sonetFarEndVTCurrentEntry 4 } -- The SONET/SDH Far End VT Interval Table -- The SONET/SDH Far End VT Interval Table -- contains various statistics -- collected by each system over a maximum -- of the previous 24 hours of -- operation. The past 24 hours may be broken into 96 -- completed 15 minute intervals. -- A system is required to store at -- least 4 completed 15 minute interval. -- The default value is 32 intervals. sonetFarEndVTIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetFarEndVTIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET/SDH Far End VT Interval table." ::= { sonetFarEndVT 2 } sonetFarEndVTIntervalEntry OBJECT-TYPE SYNTAX SonetFarEndVTIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET/SDH Far End VT Interval table." INDEX { ifIndex, sonetFarEndVTIntervalNumber } ::= { sonetFarEndVTIntervalTable 1 } SonetFarEndVTIntervalEntry ::= SEQUENCE { sonetFarEndVTIntervalNumber Integer32, sonetFarEndVTIntervalESs PerfIntervalCount, sonetFarEndVTIntervalSESs PerfIntervalCount, sonetFarEndVTIntervalCVs PerfIntervalCount, sonetFarEndVTIntervalUASs PerfIntervalCount, sonetFarEndVTIntervalValidData TruthValue } sonetFarEndVTIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { sonetFarEndVTIntervalEntry 1 } sonetFarEndVTIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH VT interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndVTIntervalEntry 2 } sonetFarEndVTIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH VT interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndVTIntervalEntry 3 } sonetFarEndVTIntervalCVs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH VT interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndVTIntervalEntry 4 } sonetFarEndVTIntervalUASs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH VT interface in a particular 15-minute interval in the past 24 hours." ::= { sonetFarEndVTIntervalEntry 5 } sonetFarEndVTIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { sonetFarEndVTIntervalEntry 6 } -- conformance information sonetConformance OBJECT IDENTIFIER ::= { sonetMIB 4 } sonetGroups OBJECT IDENTIFIER ::= { sonetConformance 1 } sonetCompliances OBJECT IDENTIFIER ::= { sonetConformance 2 } -- deprecated compliance statement sonetCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SONET/SDH interfaces." MODULE -- this module MANDATORY-GROUPS { sonetMediumStuff, sonetSectionStuff } GROUP sonetLineStuff DESCRIPTION "Implementation of this group is mandatory for all SONET/SDH systems that terminate SONET/SDH Lines, Paths or Virtual Tributaries." GROUP sonetFarEndLineStuff DESCRIPTION "Implementation of this group is optional for all SONET/SDH systems that terminate SONET/SDH Lines, Paths or Virtual Tributaries, and that provide for a far end block error (FEBE) information at the SONET/SDH Line Layer." GROUP sonetPathStuff DESCRIPTION "Implementation of this group is mandatory for all SONET/SDH systems that terminate SONET/SDH Paths or Virtual Tributaries." OBJECT sonetPathCurrentWidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP sonetFarEndPathStuff DESCRIPTION "Implementation of this group is optional for all SONET/SDH systems that terminate SONET/SDH Paths or Virtual Tributaries, and that process Far End information." GROUP sonetVTStuff DESCRIPTION "Implementation of this group is mandatory for all SONET/SDH systems that terminate SONET/SDH Virtual Tributaries." OBJECT sonetVTCurrentWidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP sonetFarEndVTStuff DESCRIPTION "Implementation of this group is optional for all SONET/SDH systems that terminate the SONET/SDH floating Virtual Tributaries, and that process Far End information." ::= { sonetCompliances 1 } -- current compliance statements sonetCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SONET/SDH interfaces." MODULE -- this module MANDATORY-GROUPS { sonetMediumStuff2, sonetSectionStuff2 } OBJECT sonetMediumType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT sonetMediumLineCoding MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT sonetMediumLineType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT sonetMediumCircuitIdentifier MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT sonetMediumLoopbackConfig MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT sonetSESthresholdSet MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the enumerated values need be supported." GROUP sonetLineStuff2 DESCRIPTION "Implementation of this group is mandatory for all SONET/SDH systems that terminate SONET/SDH Lines, Paths or Virtual Tributaries." GROUP sonetFarEndLineStuff2 DESCRIPTION "Implementation of this group is optional for all SONET/SDH systems that terminate SONET/SDH Lines, Paths or Virtual Tributaries, and that provide for a far end block error (FEBE) information at the SONET/SDH Line Layer." GROUP sonetPathStuff2 DESCRIPTION "Implementation of this group is mandatory for all SONET/SDH systems that terminate SONET/SDH Paths or Virtual Tributaries." OBJECT sonetPathCurrentWidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP sonetFarEndPathStuff2 DESCRIPTION "Implementation of this group is optional for all SONET/SDH systems that terminate SONET/SDH Paths or Virtual Tributaries, and that process Far End information." GROUP sonetVTStuff2 DESCRIPTION "Implementation of this group is mandatory for all SONET/SDH systems that terminate SONET/SDH Virtual Tributaries." OBJECT sonetVTCurrentWidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP sonetFarEndVTStuff2 DESCRIPTION "Implementation of this group is optional for all SONET/SDH systems that terminate the SONET/SDH floating Virtual Tributaries, and that process Far End information." ::= { sonetCompliances 2 } -- units of conformance -- deprecated groups sonetMediumStuff OBJECT-GROUP OBJECTS { sonetMediumType, sonetMediumTimeElapsed, sonetMediumValidIntervals, sonetMediumLineCoding, sonetMediumLineType, sonetMediumCircuitIdentifier } STATUS deprecated DESCRIPTION "A collection of objects providing configuration information applicable to all SONET/SDH interfaces." ::= { sonetGroups 1 } sonetSectionStuff OBJECT-GROUP OBJECTS { sonetSectionCurrentStatus, sonetSectionCurrentESs, sonetSectionCurrentSESs, sonetSectionCurrentSEFSs, sonetSectionCurrentCVs, sonetSectionIntervalESs, sonetSectionIntervalSESs, sonetSectionIntervalSEFSs, sonetSectionIntervalCVs } STATUS deprecated DESCRIPTION "A collection of objects providing information specific to SONET/SDH Section interfaces." ::= { sonetGroups 2 } sonetLineStuff OBJECT-GROUP OBJECTS { sonetLineCurrentStatus, sonetLineCurrentESs, sonetLineCurrentSESs, sonetLineCurrentCVs, sonetLineCurrentUASs, sonetLineIntervalESs, sonetLineIntervalSESs, sonetLineIntervalCVs, sonetLineIntervalUASs } STATUS deprecated DESCRIPTION "A collection of objects providing information specific to SONET/SDH Line interfaces." ::= { sonetGroups 3 } sonetFarEndLineStuff OBJECT-GROUP OBJECTS { sonetFarEndLineCurrentESs, sonetFarEndLineCurrentSESs, sonetFarEndLineCurrentCVs, sonetFarEndLineCurrentUASs, sonetFarEndLineIntervalESs, sonetFarEndLineIntervalSESs, sonetFarEndLineIntervalCVs, sonetFarEndLineIntervalUASs } STATUS deprecated DESCRIPTION "A collection of objects providing information specific to SONET/SDH Line interfaces, and maintaining Line Far End information." ::= { sonetGroups 4 } sonetPathStuff OBJECT-GROUP OBJECTS { sonetPathCurrentWidth, sonetPathCurrentStatus, sonetPathCurrentESs, sonetPathCurrentSESs, sonetPathCurrentCVs, sonetPathCurrentUASs, sonetPathIntervalESs, sonetPathIntervalSESs, sonetPathIntervalCVs, sonetPathIntervalUASs } STATUS deprecated DESCRIPTION "A collection of objects providing information specific to SONET/SDH Path interfaces." ::= { sonetGroups 5 } sonetFarEndPathStuff OBJECT-GROUP OBJECTS { sonetFarEndPathCurrentESs, sonetFarEndPathCurrentSESs, sonetFarEndPathCurrentCVs, sonetFarEndPathCurrentUASs, sonetFarEndPathIntervalESs, sonetFarEndPathIntervalSESs, sonetFarEndPathIntervalCVs, sonetFarEndPathIntervalUASs } STATUS deprecated DESCRIPTION "A collection of objects providing information specific to SONET/SDH Path interfaces, and maintaining Path Far End information." ::= { sonetGroups 6 } sonetVTStuff OBJECT-GROUP OBJECTS { sonetVTCurrentWidth, sonetVTCurrentStatus, sonetVTCurrentESs, sonetVTCurrentSESs, sonetVTCurrentCVs, sonetVTCurrentUASs, sonetVTIntervalESs, sonetVTIntervalSESs, sonetVTIntervalCVs, sonetVTIntervalUASs } STATUS deprecated DESCRIPTION "A collection of objects providing information specific to SONET/SDH VT interfaces." ::= { sonetGroups 7 } sonetFarEndVTStuff OBJECT-GROUP OBJECTS { sonetFarEndVTCurrentESs, sonetFarEndVTCurrentSESs, sonetFarEndVTCurrentCVs, sonetFarEndVTCurrentUASs, sonetFarEndVTIntervalESs, sonetFarEndVTIntervalSESs, sonetFarEndVTIntervalCVs, sonetFarEndVTIntervalUASs } STATUS deprecated DESCRIPTION "A collection of objects providing information specific to SONET/SDH VT interfaces, and maintaining VT Far End information." ::= { sonetGroups 8 } -- current groups sonetMediumStuff2 OBJECT-GROUP OBJECTS { sonetMediumType, sonetMediumTimeElapsed, sonetMediumValidIntervals, sonetMediumLineCoding, sonetMediumLineType, sonetMediumCircuitIdentifier, sonetMediumInvalidIntervals, sonetMediumLoopbackConfig, sonetSESthresholdSet } STATUS current DESCRIPTION "A collection of objects providing configuration information applicable to all SONET/SDH interfaces." ::= { sonetGroups 9 } sonetSectionStuff2 OBJECT-GROUP OBJECTS { sonetSectionCurrentStatus, sonetSectionCurrentESs, sonetSectionCurrentSESs, sonetSectionCurrentSEFSs, sonetSectionCurrentCVs, sonetSectionIntervalESs, sonetSectionIntervalSESs, sonetSectionIntervalSEFSs, sonetSectionIntervalCVs, sonetSectionIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing information specific to SONET/SDH Section interfaces." ::= { sonetGroups 10 } sonetLineStuff2 OBJECT-GROUP OBJECTS { sonetLineCurrentStatus, sonetLineCurrentESs, sonetLineCurrentSESs, sonetLineCurrentCVs, sonetLineCurrentUASs, sonetLineIntervalESs, sonetLineIntervalSESs, sonetLineIntervalCVs, sonetLineIntervalUASs, sonetLineIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing information specific to SONET/SDH Line interfaces." ::= { sonetGroups 11 } sonetPathStuff2 OBJECT-GROUP OBJECTS { sonetPathCurrentWidth, sonetPathCurrentStatus, sonetPathCurrentESs, sonetPathCurrentSESs, sonetPathCurrentCVs, sonetPathCurrentUASs, sonetPathIntervalESs, sonetPathIntervalSESs, sonetPathIntervalCVs, sonetPathIntervalUASs, sonetPathIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing information specific to SONET/SDH Path interfaces." ::= { sonetGroups 12 } sonetVTStuff2 OBJECT-GROUP OBJECTS { sonetVTCurrentWidth, sonetVTCurrentStatus, sonetVTCurrentESs, sonetVTCurrentSESs, sonetVTCurrentCVs, sonetVTCurrentUASs, sonetVTIntervalESs, sonetVTIntervalSESs, sonetVTIntervalCVs, sonetVTIntervalUASs, sonetVTIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing information specific to SONET/SDH VT interfaces." ::= { sonetGroups 13 } sonetFarEndLineStuff2 OBJECT-GROUP OBJECTS { sonetFarEndLineCurrentESs, sonetFarEndLineCurrentSESs, sonetFarEndLineCurrentCVs, sonetFarEndLineCurrentUASs, sonetFarEndLineIntervalESs, sonetFarEndLineIntervalSESs, sonetFarEndLineIntervalCVs, sonetFarEndLineIntervalUASs, sonetFarEndLineIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing information specific to SONET/SDH Line interfaces, and maintaining Line Far End information." ::= { sonetGroups 14 } sonetFarEndPathStuff2 OBJECT-GROUP OBJECTS { sonetFarEndPathCurrentESs, sonetFarEndPathCurrentSESs, sonetFarEndPathCurrentCVs, sonetFarEndPathCurrentUASs, sonetFarEndPathIntervalESs, sonetFarEndPathIntervalSESs, sonetFarEndPathIntervalCVs, sonetFarEndPathIntervalUASs, sonetFarEndPathIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing information specific to SONET/SDH Path interfaces, and maintaining Path Far End information." ::= { sonetGroups 15 } sonetFarEndVTStuff2 OBJECT-GROUP OBJECTS { sonetFarEndVTCurrentESs, sonetFarEndVTCurrentSESs, sonetFarEndVTCurrentCVs, sonetFarEndVTCurrentUASs, sonetFarEndVTIntervalESs, sonetFarEndVTIntervalSESs, sonetFarEndVTIntervalCVs, sonetFarEndVTIntervalUASs, sonetFarEndVTIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing information specific to SONET/SDH VT interfaces, and maintaining VT Far End information." ::= { sonetGroups 16 } END