IANA-PRINTER-MIB DEFINITIONS ::= BEGIN -- http://www.iana.org/assignments/ianaprinter-mib IMPORTS MODULE-IDENTITY, mib-2 FROM SNMPv2-SMI -- [RFC2578] TEXTUAL-CONVENTION FROM SNMPv2-TC; -- [RFC2579] ianaPrinterMIB MODULE-IDENTITY LAST-UPDATED "201907080000Z" -- July 8, 2019 ORGANIZATION "IANA" CONTACT-INFO "Internet Assigned Numbers Authority Postal: ICANN 12025 Waterfront Drive, Suite 300 Los Angeles, CA 90094-2536 Tel: +1 310-301-5800 E-Mail: iana&iana.org" DESCRIPTION "This MIB module defines a set of printing-related TEXTUAL-CONVENTIONs for use in Printer MIB (RFC 3805), Finisher MIB (RFC 3806), and other MIBs which need to specify printing mechanism details. Any additions or changes to the contents of this MIB module require either publication of an RFC, or Designated Expert Review as defined in RFC 2434, Guidelines for Writing an IANA Considerations Section in RFCs. The Designated Expert will be selected by the IESG Area Director(s) of the Applications Area. Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3805. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html" REVISION "201907080000Z" -- July 8, 2019 DESCRIPTION "Updated PrtAlertGroupTC and PrtAlertCodeTC to cover groups and codes defined in Sections 5.1, 5.2, and 5.3 of PWG MFD Alerts [PWG5107.3-2019]." REVISION "201609140000Z" -- September 14, 2016 DESCRIPTION "Replaced references to RFC 2911 with references to RFC8011." REVISION "201608170000Z" -- August 17, 2016 DESCRIPTION "Replaced references to RFC 2910 with references to RFC 8010." REVISION "201405220000Z" -- May 22, 2014 DESCRIPTION "Updated contact info." REVISION "201309230000Z" -- September 23, 2013 DESCRIPTION "Added 8 in PrtInputTypeTC." REVISION "201207190000Z" -- July 19, 2012 DESCRIPTION "Added 84-85 in PrtInterpreterLangFamilyTC." REVISION "201111040000Z" -- November 4, 2011 DESCRIPTION "Added 35-36 in PrtMarkerSuppliesTypeTC." REVISION "201005170000Z" -- May 17, 2010 DESCRIPTION "Added 72-83 in PrtInterpreterLangFamilyTC, 600+ lines from 30203-31838 in PrtAlertCodeTC." REVISION "201004070000Z" -- April 7, 2010 DESCRIPTION "Added langJDF(68), langJMF(69), langPPML(70), and langXHTMLPrint(71)." REVISION "200911230000Z" -- November 23, 2009 DESCRIPTION "Added langXPS(66) and langOpenXPS(67)." REVISION "200910140000Z" -- October 14, 2009 DESCRIPTION "Added references for langPCLXL(47), langART(48), and langTIPSI(49)." REVISION "200902060000Z" -- February 6, 2009 DESCRIPTION "Added chWSPrint(46) 'Channel Type' for Web Services based printing." REVISION "200509140000Z" -- September 14, 2005 DESCRIPTION "Updates to include missing 'unknown' values for PrtCoverStatusTC, PrtChannelTypeTC, PrtAlertGroupTC and removal of comment for for PrtAlertGroupTC." REVISION "200406020000Z" -- June 2, 2004 DESCRIPTION "Original version, published in coordination with Printer MIB (RFC 3805)." ::= { mib-2 109 } -- -- Generic TEXTUAL-CONVENTIONs -- PrtCoverStatusTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtCoverStatus in RFC 1759. STATUS current DESCRIPTION "Values for encoding the state of a particular cover or access panel on the printer case or enclosure." SYNTAX INTEGER { other(1), unknown(2), coverOpen(3), coverClosed(4), interlockOpen(5), interlockClosed(6) } -- -- General Group TEXTUAL-CONVENTIONs -- PrtGeneralResetTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtGeneralReset in RFC 1759. STATUS current DESCRIPTION "Values for reading and writing the prtGeneralReset object. If a device does not have NVRAM, the device shall none the less respond to a SET with the value resetToNVRAM(5) with a sort of warm reset that resets the device to implementation- defined state that is preferably under control of the system administrator by some means outside the scope of the Printer MIB specification." SYNTAX INTEGER { notResetting(3), powerCycleReset(4), -- Cold Start resetToNVRAM(5), -- Warm Start resetToFactoryDefaults(6) -- Reset contents of -- NVRAM to factory -- defaults } -- -- Channel Group TEXTUAL-CONVENTIONs -- PrtChannelTypeTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtChannelType in RFC 1759. STATUS current DESCRIPTION "This enumeration indicates the type of channel that is receiving jobs." SYNTAX INTEGER { other(1), unknown(2), chSerialPort(3), chParallelPort(4), chIEEE1284Port(5), chSCSIPort(6), chAppleTalkPAP(7), -- AppleTalk Printer -- Access Protocol (PAP) -- -- prtChannelInformation entry: -- -- Printer Name -- Keyword: Name -- Syntax: Name -- Status: Optional -- Multiplicity: Single -- Description: The name of the printer -- within the AppleTalk naming scope chLPDServer(8), -- prtChannelInformation entry: -- -- Printer queue name -- Keyword: Queue -- Syntax: Name -- Status: Mandatory -- Multiplicity: Single -- Description: queue name as -- defined in [RFC1179]. chNetwareRPrinter(9), -- Novell, Inc. -- For each entry of this type, the -- prtChannelInformation must have a pair of -- keywords. For Netware 3.x channels this must -- be a (PServer, Printer) pair. For Netware -- 4.x channels and for IntranetWare channels -- this must be a (NDSTree, NDSPrinter) pair. -- -- prtChannelInformation entries: -- Print Server Name -- Keyword: PServer -- Syntax: Name -- Status: Mandatory -- Multiplicity: Single -- Description: The Pserver's SAP name -- -- Printer Number -- Keyword: Printer -- Syntax: Integer -- Status: Mandatory -- Multiplicity: Single -- Description: The printer number -- -- NDSTree -- Keyword: NDSTree -- Syntax: Name -- Multiplicity: Single -- Description: The tree's SAP name -- -- NDS Printer object -- Keyword: NDSPrinter -- Syntax: Text (Unicode) -- Status: Mandatory -- Multiplicity: Single -- Description: The fully qualified -- name of the Printer -- -- In the Netware 3.x environment, the -- client checks the Bindery object -- representing the named PServer. The -- client then checks for queues which -- are associated with the numbered -- printer. In the 4.x and IntraNetware -- environment, the client looks up the -- queues which are associated with the -- NDS Printer Object in the named Tree. -- Depending on client access rights to -- those queues, the client submits jobs -- to the appropriate queue. chNetwarePServer(10), -- Novell,Inc. -- For each entry of this type, the -- prtChannelInformation must have a pair -- of keywords. For Netware 3.x channels -- this must be a (Server, PServer) pair. -- For Netware 4.x and IntranetWare -- channels, this must be a -- (NDSTree, NDSPServer) pair. -- -- prtChannelInformation entries: -- -- Server Name -- Keyword: Server -- Syntax: Name -- Status: Mandatory -- Multiplicity: Single -- Description: The SAP name of the -- server for which the PServer is defined. -- -- PServer -- Keyword: PServer -- Syntax: Name -- Status: Mandatory -- Multiplicity: Single -- Description: The bindery name of -- the PServer -- -- NDS Tree -- Keyword: NDSTree -- Syntax: Name -- Status: Mandatory -- Multiplicity: Single -- Description: The NDS Tree name -- -- PServer -- Keyword: NDSPServer -- Syntax: Text (Unicode) -- Status: Mandatory -- Multiplicity: Single -- Description: The fully qualified -- name of the PServer object in the tree. -- -- In the 3.x environment, the client -- checks the bindery object -- representing the named PServer on the -- named Server. In the 4.x and -- IntranetWare environment, -- the client checks the NDS object -- representing the named PServer in the -- named Tree. In either case, the -- client then checks for all queues -- associated with the Pserver object. -- Depending on client access rights -- to those queues, the client submits -- jobs to the appropriate queue. chPort9100(11), -- DEPRECATED -- (see chPortTCP - 37; chBidirPortTCP - 38) chAppSocket(12), -- A bi-directional, LPD-like, protocol using -- 9101 for control and 9100 for data. -- Adobe Systems, Inc. chFTP(13), -- [RFC959] chTFTP(14), -- [RFC1350] chDLCLLCPort(15), chIBM3270(16), -- IBM Coax chIBM5250(17), -- IBM Twinax chFax(18), chIEEE1394(19), chTransport1(20), -- TCP port 35, for reserved TCP port list see -- [RFC3232]. This RFC should also be -- referenced for other channel -- enumerations utilizing TCP port -- numbers 0 through 1024. chCPAP(21), -- TCP port 170 -- Digital Equipment Corp. chDCERemoteProcCall(22), -- OSF -- DEPRECATED chONCRemoteProcCall(23), -- SUN Microsystems -- DEPRECATED chOLE(24), -- Microsoft -- DEPRECATED chNamedPipe(25), chPCPrint(26), -- Banyan chServerMessageBlock(27), -- File/Print sharing protocol used by -- various network operating systems -- from IBM 3Com, Microsoft and others -- -- prtChannelInformation entry: -- -- Service Name -- Keyword: Name -- Syntax: Name -- Status: Optional -- Multiplicity: Single -- Description: The service name of -- the printer chDPMF(28), -- IBM Infoprint chDLLAPI(29), -- Microsoft -- DEPRECATED chVxDAPI(30), -- Microsoft -- DEPRECATED chSystemObjectManager(31), -- IBM chDECLAT(32), -- Digital Equipment Corp. -- -- prtChannelInformation entries: -- -- Port Name -- Keyword: Port -- Syntax: Name -- Status: Conditionally -- Mandatory -- (see note below) -- Multiplicity: Single -- Description: LAT port name -- -- Service Name -- Keyword: Service -- Syntax: Name -- Status: Conditionally -- Mandatory -- Multiplicity: Single -- Description: LAT service name -- -- The LAT channel may be -- identified by either a port or -- service, so either a -- Port or Service entry must be -- specified, but not both. chNPAP(33), chUSB(34), -- Not in RFC 1759 -- Universal Serial Bus chIRDA(35), -- Not in RFC 1759 -- Infrared Data Assoc. Prot. chPrintXChange(36), -- Not in RFC 1759 -- PrintXChange Protocol chPortTCP(37), -- Not in RFC 1759 -- A unidirectional "raw" TCP -- channel that uses an administratively -- assigned TCP port address. -- -- prtChannelInformation entry: -- -- Port Number -- Keyword: Port -- Syntax: decimal number -- Status: Mandatory -- Multiplicity: Single -- Description: TCP port number chBidirPortTCP(38), -- Not in RFC 1759 -- A bi-directional version of chPortTCP -- -- prtChannelInformation entries: -- (See chPortTCP) chUNPP(39), -- Not in RFC 1759 -- Universal Network Printing -- Protocol(UNPP). A bi-directional, -- multiport network printing -- application protocol available on -- multiple transport protocols. -- Underscore, Inc. -- Contact: info&underscore.com chAppleTalkADSP(40), -- Not in RFC 1759 -- AppleTalk Data Stream Protocol. -- ADSP is part of the AppleTalk -- suite of protocols. -- It is a symmetric, connection- -- oriented protocol that makes -- possible the establishment -- and maintenance of full-duplex -- streams of data bytes between -- two sockets in an AppleTalk -- internet. -- See [APPLEMAC]. chPortSPX(41), -- Not in RFC 1759 -- Sequenced Packet Exchange (SPX) -- socket. -- Novell, Inc. Similar to TCP, a -- bi-directional data pipe using -- Novell SPX as a transport. -- -- prtChannelInformation entries: -- -- Network Number -- Keyword: Net -- Syntax: HexString -- Status: Mandatory -- Multiplicity: Single -- Description: The network number -- -- Node Number -- Keyword: Node -- Syntax: HexString -- Status: Mandatory -- Multiplicity: Single -- Description: The node number -- -- Socket Number -- Keyword: Socket -- Syntax: HexString -- Status: Mandatory -- Multiplicity: Single -- Description: The SPX socket number -- -- There must be exactly one "Net" and -- one "Node" and one "Socket" entry. A -- HexString is a binary value -- represented as a string of -- ASCII characters using hexadecimal -- notation. chPortHTTP(42), -- Not in RFC 1759 -- Hypertext Transfer Protocol. See [RFC1945] -- and [RFC2616]. chNDPS(43), -- Not in RFC 1759 -- Novell, Inc. -- -- prtChannelInformation entry: -- -- Printer Agent Name -- Keyword: PA -- Syntax: Name -- Status: Mandatory -- Multiplicity: Single -- Description: The NDPS Printer -- Agent Name chIPP(44), -- Not in RFC 1759 -- Internet Printing Protocol (IPP), -- (IPP/1.1 - see [RFC 8010] and -- [RFC8011]) -- also applies to all future versions of IPP. -- -- IPP Printer URI -- Keyword: URI -- Syntax: URI (Unicode UTF-8 per -- [RFC2396]) -- Status: Mandatory -- Multiplicity: Single -- Default: not applicable -- Description: URI of this IPP Printer -- within Internet naming scope. Unicode -- UTF-8 [RFC3629] string with -- hexadecimal escapes for any non-ASCII -- characters (per [RFC2396]). -- Conformance: An IPP Printer shall list all -- IPP URI it supports (one per IPP Channel -- entry). If a URI contains the 'http:' -- scheme it must have an explicit port. -- See: [RFC3629], [RFC2396], -- [RFC 8010], -- [RFC8011]. -- -- IPP Printer Client Authentication -- Keyword: Auth -- Syntax: Keyword -- Status: Optional -- Multiplicity: Single -- Default: 'none' -- Description: A client authentication -- mechanism supported for this IPP Printer -- URI: -- 'none' -- no client authentication mechanism -- 'requesting-user-name' -- authenticated user in 'requesting- -- user-name' -- 'basic' -- authenticated user via HTTP Basic -- mechanism -- 'digest' -- authenticated user via HTTP Digest -- mechanism -- 'certificate' -- authenticated user via certificate -- mechanism -- Conformance: An IPP Printer should list -- all IPP client authentication mechanisms -- it supports (one per IPP Channel entry). -- See: [RFC 8011] and -- [RFC 8010]. -- -- IPP Printer Security -- Keyword: Security -- Syntax: Keyword -- Status: Optional -- Multiplicity: Single -- Default: 'none' -- Description: A security mechanism -- supported for this IPP Printer URI: -- 'none' -- no security mechanism -- 'ssl3' -- SSL3 secure communications channel -- protocol -- 'tls' -- TLS secure communications channel -- protocol -- Conformance: An IPP Printer should list -- all IPP security mechanisms it supports -- (one per IPP Channel entry). -- See: [RFC2246], [RFC8011]. -- -- IPP Printer Protocol Version -- Keyword: Version -- Syntax: Keyword -- Status: Optional -- Multiplicity: Multiple -- Default: '1.1' -- Description: All of the IPP protocol -- versions (major.minor) supported for -- this IPP Printer URI: -- '1.0' -- IPP/1.0 conforming Printer -- '1.1' -- IPP/1.1 conforming Printer -- Conformance: An IPP Printer should list -- all IPP versions it supports (all listed -- in each IPP Channel entry). An IPP -- Client should select the highest -- numbered version the IPP Client supports -- for use in all IPP Requests (for optimum -- interworking). -- See: [RFC8011]. chSMTP(45), -- Print Job submission via Simple Mail -- Transfer Protocol (SMTP) - see [RFC2821] -- -- prtChannelInformation entry: -- -- Keyword: Mailto -- Syntax: Name -- Status: Mandatory -- Multiplicity: Single -- Default: not applicable -- Description: The SMTP URL of the printer. chWSPrint(46) -- Not in RFC 3805 -- Web Services on Devices Printer (WS-Print), -- (WS-Print 1.0 - see [WS-Print]) -- -- WS-Print Service URL -- Keyword: ServiceURL -- Syntax: URI (Unicode UTF-8 per -- [RFC3986]) -- Status: Mandatory -- Multiplicity: Multiple -- Default: not applicable -- Description: URL of this WS-Print Printer -- within Internet naming scope. Unicode -- UTF-8 [RFC3629] string with -- hexadecimal escapes for any non-ASCII -- characters (per [RFC3986]). -- Conformance: A WS-Print Printer shall list -- all URLs it -- -- WS-Print Web Services Target Namespace -- Keyword: Namespace -- Syntax: 'URI (Unicode UTF-8 per RFC 3986) -- Status: Optional -- Multiplicity: Multiple -- Default: http://schemas.microsoft.com/windows/2006/08/wdp/print -- Description: XML Namespace for the Service -- and associated print service model. Unicode -- UTF-8 [RFC3629] string with -- hexadecimal escapes for any non-ASCII -- characters (per [RFC3986]). -- Conformance: A WS-Print Printer shall list -- all interoperable WS-Print namespaces it -- supports. } -- -- Interpreter Group TEXTUAL-CONVENTIONs -- PrtInterpreterLangFamilyTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtInterpreterLangFamily in RFC 1759. STATUS current DESCRIPTION "This enumeration indicates the type of interpreter that is receiving jobs." SYNTAX INTEGER { other(1), unknown(2), -- Not in RFC 1759 langPCL(3), -- PCL. Starting with PCL version 5, -- HP-GL/2 is included as part of the -- PCL language. -- PCL and HP-GL/2 are registered -- trademarks of Hewlett-Packard -- Company. langHPGL(4), -- Hewlett-Packard Graphics Language. -- HP-GL is a registered trademark of -- Hewlett-Packard Company. langPJL(5), -- Peripheral Job Language. Appears in -- the data stream between data intended -- for a page description language. -- Hewlett-Packard Co. langPS(6), -- PostScript (tm) Language -- Postscript - a trademark of Adobe -- Systems Incorporated which may be -- registered in certain jurisdictions langIPDS(7), -- Intelligent Printer Data Stream -- Bi-directional print data stream for -- documents consisting of data objects -- (text, image, graphics, bar codes), -- resources (fonts, overlays) and page, -- form and finishing instructions. -- Facilitates system level device -- control, document tracking and error -- recovery throughout the print -- process. -- IBM Corporation. langPPDS(8), -- IBM Personal Printer Data Stream. -- Originally called IBM ASCII, the name -- was changed to PPDS when the Laser -- Printer was introduced in 1989. -- Lexmark International, Inc. langEscapeP(9), -- Epson Corp. langEpson(10), langDDIF(11), -- Digital Document Interchange Format -- Digital Equipment Corp., Maynard MA langInterpress(12), -- Xerox Corp. langISO6429(13), -- ISO 6429. Control functions for -- Coded Character Sets (has ASCII -- control characters, plus additional -- controls for -- character imaging devices.) langLineData(14), -- line-data: Lines of data as -- separate ASCII or EBCDIC records -- and containing no control functions -- (no CR, LF, HT, FF, etc.) -- For use with traditional line -- printers. May use CR and/or LF to -- delimit lines, instead of records. -- See ISO 10175 Document Printing -- Application (DPA) [ISO10175]. langMODCA(15), -- Mixed Object Document Content -- Architecture -- Definitions that allow the -- composition, interchange, and -- presentation of final form -- documents as a collection of data -- objects (text, image, graphics, bar -- codes), resources (fonts, overlays) -- and page, form and finishing -- instructions. -- IBM Corporation. langREGIS(16), -- Remote Graphics Instruction Set, -- Digital Equipment Corp., Maynard MA langSCS(17), -- SNA Character String -- Bi-directional print data stream for -- SNA LU-1 mode of communication. -- IBM langSPDL(18), -- ISO 10180 Standard Page Description -- Language -- ISO Standard langTEK4014(19), -- Tektronix Corp. langPDS(20), langIGP(21), -- Printronix Corp. langCodeV(22), -- Magnum Code-V, Image and printer -- control language used to control -- impact/dot-matrix printers. -- QMS, Inc., Mobile AL langDSCDSE(23), -- DSC-DSE: Data Stream Compatible and -- Emulation Bi-directional print data -- stream for non-SNA (DSC) and SNA LU-3 -- 3270 controller (DSE) communications -- IBM langWPS(24), -- Windows Printing System, Resource -- based command/data stream used by -- Microsoft At Work Peripherals. -- Developed by the Microsoft -- Corporation. langLN03(25), -- Early DEC-PPL3, Digital Equipment -- Corp. langCCITT(26), langQUIC(27), -- QUIC (Quality Information Code), Page -- Description Language for laser -- printers. Included graphics, printer -- control capability and emulation of -- other well-known printer. -- QMS, Inc. langCPAP(28), -- Common Printer Access Protocol -- Digital Equipment Corp. langDecPPL(29), -- Digital ANSI-Compliant Printing -- Protocol -- (DEC-PPL) -- Digital Equipment Corp. langSimpleText(30), -- simple-text: character coded data, -- including NUL, CR , LF, HT, and FF -- control characters. See ISO 10175 -- Document Printing Application (DPA) -- [ISO10175]. langNPAP(31), -- Network Printer Alliance Protocol -- (NPAP). This protocol has been -- superseded by the IEEE 1284.1 TIPSI -- Std (ref. LangTIPSI(49)). langDOC(32), -- Document Option Commands, Appears in -- the data stream between data -- intended for a page description. -- QMS, Inc. langimPress(33), -- imPRESS, Page description language -- originally developed for the -- ImageServer product line. A binary -- language providing representations -- of text, simple graphics, and some -- large forms (simple -- bit-map and CCITT group 3/4 -- encoded).The -- language was intended to be sent over -- an 8-bit channel and supported early -- document preparation languages (e.g., -- TeX and TROFF). -- QMS, Inc. langPinwriter(34), -- 24 wire dot matrix printer for -- USA, Europe, and Asia except -- Japan. -- More widely used in Germany, and -- some Asian countries than in US. -- NEC langNPDL(35), -- Page printer for Japanese market. -- NEC langNEC201PL(36), -- Serial printer language used in -- the Japanese market. -- NEC langAutomatic(37), -- Automatic PDL sensing. Automatic -- sensing of the interpreter -- language family by the printer -- examining the document content. -- Which actual interpreter language -- families are sensed depends on -- the printer implementation. langPages(38), -- Page printer Advanced Graphic -- Escape Set -- IBM Japan langLIPS(39), -- LBP Image Processing System langTIFF(40), -- Tagged Image File Format (Aldus) langDiagnostic(41), -- A hex dump of the input to the -- interpreter langPSPrinter(42), -- The PostScript Language used for -- control (with any PDLs) -- Adobe Systems Incorporated langCaPSL(43), -- Canon Print Systems Language langEXCL(44), -- Extended Command Language -- Talaris Systems Inc. langLCDS(45), -- Line Conditioned Data Stream -- Xerox Corporation langXES(46), -- Xerox Escape Sequences -- Xerox Corporation langPCLXL(47), -- Not in RFC 1759 -- Printer Control Language. Extended -- language features for printing, and -- printer control. -- Tammy Ferguson (HP) -- and Binnur Al-Kazily (HP) -- Technical reference manual: None -- Hewlett-Packard Co. langART(48), -- Not in RFC 1759 -- Advanced Rendering Tools (ART). -- Page Description language -- originally developed for the Laser -- Press printers. -- Norio Iwamoto (Fuji Xerox) -- and Tom Hastings (Xerox) -- Technical reference manual: "ART IV -- Reference Manual", No F33M. -- Fuji Xerox Co., Ltd. langTIPSI(49), -- Not in RFC 1759 -- Transport Independent Printer -- System Interface -- Don Wright (Lexmark) -- Technical reference manual: "IEEE -- 1284.1" langPrescribe(50), -- Not in RFC 1759 -- Page description and printer -- control language. It can be -- described with ordinary ASCII -- Technical reference manual: -- "PRESCRIBE II Programming Manual" langLinePrinter(51), -- Not in RFC 1759 -- A simple-text character stream which -- supports the control codes LF, VT, -- FF, and plus Centronics or -- Dataproducts Vertical Format Unit -- (VFU) language is commonly used on -- many older model line and matrix -- printers. langIDP(52), -- Not in RFC 1759 -- Imaging Device Protocol -- Apple Computer. langXJCL(53), -- Not in RFC 1759 -- Xerox Job Control Language (JCL). -- A Job Control language originally -- developed for the LaserPress printers -- and is capable of switching PDLs. -- Technical reference manual: -- "ART IV Reference Manual", No F33M. -- Fuji Xerox Co., Ltd. langPDF(54), -- Not in RFC 1759 -- Adobe Portable Document Format -- Adobe Systems, Inc. langRPDL(55), -- Not in RFC 1759 -- Ricoh Page Description Language for -- printers. -- Technical manual "RPDL command -- reference" No.307029 -- RICOH, Co. LTD langIntermecIPL(56), -- Not in RFC 1759 -- Intermec Printer Language for label -- printers. -- Technical Manual: "IPL Programmers -- Reference Manual" -- Intermec Corporation langUBIFingerprint(57), -- Not in RFC 1759 -- An intelligent basic-like programming -- language for label printers. -- Reference Manual: "UBI Fingerprint -- 7.1", No. 1-960434-00 -- United Barcode Industries langUBIDirectProtocol(58), -- Not in RFC 1759 -- An intelligent control language for -- label printers. -- Programmers guide: " UBI Direct -- Protocol", No. 1-960419-00 -- United Barcode Industries langFujitsu(59), -- Not in RFC 1759 -- Fujitsu Printer Language -- Reference Manual: -- "FM Printer Sequence" No. 80HP-0770 -- FUJITSU LIMITED langCGM(60), -- Not in RFC 1759 -- Computer Graphics Metafile -- MIME type 'image/cgm' langJPEG(61), -- Not in RFC 1759 -- Joint Photographic Experts Group -- MIME type 'image/jpeg' langCALS1(62), -- Not in RFC 1759 -- US DOD CALS1 (see MIL-STD-1840) -- MIME type 'application/cals-1840' langCALS2(63), -- Not in RFC 1759 -- US DOD CALS2 (see MIL-STD-1840) -- MIME type 'application/cals-1840' langNIRS(64), -- Not in RFC 1759 -- US DOD NIRS (see MIL-STD-1840) -- MIME type 'application/cals-1840' langC4(65), -- Not in RFC 1759 -- US DOD C4 (see MIL-STD-1840) -- MIME type 'application/cals-1840' langXPS(66), -- Not in RFC 3805 -- Microsoft XML Paper Specification -- http://www.microsoft.com/whdc/xps/xpsspec langOpenXPS(67), -- Not in RFC 3805 -- ECMA OpenXPS -- http://www.ecma-international.org/ -- publications/standards/Ecma-388.htm langJDF(68), -- Not in RFC 3805 -- CIP4 Job Definition Format -- http://www.cip4.org/documents/ -- jdf_specifications/JDF1.4a.pdf langJMF(69), -- Not in RFC 3805 -- CIP4 Job Messaging Format -- also defined in CIP4 JDF specification -- http://www.cip4.org/documents/ -- jdf_specifications/JDF1.4a.pdf langPPML(70), -- Not in RFC 3805 -- PODI Personalized Print Markup Language -- http://ppml.podi.org/ppml-docs/ -- ppml-specifications.php langXHTMLPrint(71), -- Not in RFC 3805 -- W3C XHTML-Print -- http://www.w3.org/TR/xhtml-print/ langPDFis(72), -- Not in RFC 3805 -- PWG PDF Image-Streamable (PWG 5102.3) -- ftp://pwg.org/pub/pwg/candidates/ -- cs-ifxpdfis10-20040315-5102.3.pdf -- See also 'langPDF' langPDF13(73), -- Not in RFC 3805 -- Adobe Portable Document Format v1.3 -- http://www.adobe.com/devnet/ -- pdf/pdfs/PDFReference13.pdf -- See also 'langPDF' langPDF14(74), -- Not in RFC 3805 -- Adobe Portable Document Format v1.4 -- http://www.adobe.com/devnet/ -- pdf/pdfs/PDFReference.pdf -- See also 'langPDF' langPDF15(75), -- Not in RFC 3805 -- Adobe Portable Document Format v1.5 -- http://www.adobe.com/devnet/ -- pdf/pdfs/PDFReference15_v5.pdf -- See also 'langPDF' langPDF16(76), -- Not in RFC 3805 -- Adobe Portable Document Format v1.6 -- http://www.adobe.com/devnet/ -- pdf/pdfs/PDFReference16.pdf -- See also 'langPDF' langPDF17(77), -- Not in RFC 3805 -- Adobe Portable Document Format v1.7 -- http://www.adobe.com/devnet/ -- acrobat/pdfs/pdf_reference_1-7.pdf -- Equivalent to ISO 32000-1:2008 -- See also 'langPDF' langPS2(78), -- Not in RFC 3805 -- Adobe PostScript Second Edition -- http://partners.adobe.com/public/ -- developer/en/ps/psrefman.pdf -- See also 'langPS' langPS3(79), -- Not in RFC 3805 -- Adobe PostScript Third Edition -- http://www.adobe.com/products/ -- postscript/pdfs/PLRM.pdf -- See also 'langPS' langPCL3(80), -- Not in RFC 3805 -- HP Printer Command Language 3 -- No technical reference manual online -- See also 'langPCL' langPCL3GUI(81), -- Not in RFC 3805 -- HP Printer Command Language 3 GUI -- No technical reference manual online -- See also 'langPCL' langPCL5e(82), -- Not in RFC 3805 -- HP Printer Command Language 5 Enhanced -- http://h20000.www2.hp.com/bc/docs/ -- support/SupportManual/bpl13210/ -- bpl13210.pdf -- See also 'langPCL' langPCL5c(83), -- Not in RFC 3805 -- HP Printer Command Language 5 Color -- http://h20000.www2.hp.com/bc/docs/ -- support/SupportManual/bpl13212/ -- bpl13212.pdf -- See also 'langPCL' langPWGRaster(84), -- Not in RFC 1759 -- PWG 5102.4: PWG Raster Format -- ftp://ftp.pwg.org/pub/pwg/candidates/ -- cs-ippraster10-20120420-5102.4.pdf -- MIME type "image/pwg-raster" langAppleRaster(85) -- Not in RFC 1759 -- Apple raster format for printing -- No public specifications available at this time. } -- -- Input/Output Group TEXTUAL-CONVENTIONs -- PrtInputTypeTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtInputType in RFC 1759. STATUS current DESCRIPTION "The type of technology (discriminated primarily according to feeder mechanism type) employed by a specific component or components." SYNTAX INTEGER { other(1), unknown(2), sheetFeedAutoRemovableTray(3), sheetFeedAutoNonRemovableTray(4), sheetFeedManual(5), continuousRoll(6), continuousFanFold(7), sheetFeedPull(8) } PrtOutputTypeTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtOutputType in RFC 1759. STATUS current DESCRIPTION "The Type of technology supported by this output subunit." SYNTAX INTEGER { other(1), unknown(2), removableBin(3), unRemovableBin(4), continuousRollDevice(5), mailBox(6), continuousFanFold(7) } -- -- Marker Group TEXTUAL-CONVENTIONs -- PrtMarkerMarkTechTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtMarkerMarkTech in RFC 1759. STATUS current DESCRIPTION "The type of marking technology used for this marking subunit." SYNTAX INTEGER { other(1), unknown(2), electrophotographicLED(3), electrophotographicLaser(4), electrophotographicOther(5), impactMovingHeadDotMatrix9pin(6), impactMovingHeadDotMatrix24pin(7), impactMovingHeadDotMatrixOther(8), impactMovingHeadFullyFormed(9), impactBand(10), impactOther(11), inkjetAqueous(12), inkjetSolid(13), inkjetOther(14), pen(15), thermalTransfer(16), thermalSensitive(17), thermalDiffusion(18), thermalOther(19), electroerosion(20), electrostatic(21), photographicMicrofiche(22), photographicImagesetter(23), photographicOther(24), ionDeposition(25), eBeam(26), typesetter(27) } PrtMarkerSuppliesTypeTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtMarkerSuppliesType in RFC 1759. STATUS current DESCRIPTION "The type of this supply." SYNTAX INTEGER { other(1), unknown(2), -- Values for Printer MIB toner(3), wasteToner(4), ink(5), inkCartridge(6), inkRibbon(7), wasteInk(8), opc(9), -- photo conductor developer(10), fuserOil(11), solidWax(12), ribbonWax(13), wasteWax(14), fuser(15), -- Not in RFC 1759 coronaWire(16), -- Not in RFC 1759 fuserOilWick(17), -- Not in RFC 1759 cleanerUnit(18), -- Not in RFC 1759 fuserCleaningPad(19), -- Not in RFC 1759 transferUnit(20), -- Not in RFC 1759 tonerCartridge(21), -- Not in RFC 1759 fuserOiler(22), -- Not in RFC 1759 -- End of values for Printer MIB -- Values for Finisher MIB water(23), -- Not in RFC 1759 wasteWater(24), -- Not in RFC 1759 glueWaterAdditive(25),-- Not in RFC 1759 wastePaper(26), -- Not in RFC 1759 bindingSupply(27), -- Not in RFC 1759 bandingSupply(28), -- Not in RFC 1759 stitchingWire(29), -- Not in RFC 1759 shrinkWrap(30), -- Not in RFC 1759 paperWrap(31), -- Not in RFC 1759 staples(32), -- Not in RFC 1759 inserts(33), -- Not in RFC 1759 covers(34), -- Not in RFC 1759 matteToner(35), -- Not in RFC 3805 matteInk(36) -- Not in RFC 3805 -- End of values for Finisher MIB } -- -- Media Path TEXTUAL-CONVENTIONs -- PrtMediaPathTypeTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtMediaPathType in RFC 1759. STATUS current DESCRIPTION "The type of the media path for this media path." SYNTAX INTEGER { other(1), unknown(2), longEdgeBindingDuplex(3), shortEdgeBindingDuplex(4), simplex(5) } -- -- Console Group TEXTUAL-CONVENTIONs -- PrtConsoleColorTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtConsoleColor in RFC 1759. STATUS current DESCRIPTION "The color of this light." SYNTAX INTEGER { other(1), unknown(2), white(3), red(4), green(5), blue(6), cyan(7), magenta(8), yellow(9), orange(10) -- Not in RFC 1759 } PrtConsoleDisableTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtConsoleDisable in RFC 1759. STATUS current DESCRIPTION "This value indicates whether or not input is accepted from the operator console. A value of 'enabled' indicates that input is accepted from the console, and a value of 'disabled' indicates that input is not accepted from the console. " SYNTAX INTEGER { enabled(3), disabled(4) } -- -- Alert Group TEXTUAL-CONVENTIONs -- PrtAlertTrainingLevelTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtAlertTrainingLevel in RFC 1759. STATUS current DESCRIPTION "The level of training required to handle this alert, if human intervention is required. The noInterventionRequired value should be used if the event does not require any human intervention. The training level is an enumeration that is determined and assigned by the printer manufacturer based on the information or training required to handle this alert. The printer will break alerts into these different training levels. It is the responsibility of a management application in the system to determine how a particular alert is handled and how and to whom that alert is routed. The following are the four training levels of alerts: Field Service - Alerts that typically require advanced training and technical knowledge of the printer and its subunits. An example of a technical person would be a manufacturer's Field Service representative, or other person formally trained by the manufacturer or similar representative. Trained - Alerts that require an intermediate or moderate knowledge of the printer and its subunits. A typical example of such an alert is replacing a toner cartridge. Untrained - Alerts that can be fixed without prior training either because the action to correct the alert is obvious or the printer can help the untrained person fix the problem. A typical example of such an alert is reloading paper trays or emptying output bins on a low end printer. Management - Alerts that have to do with overall operation of and configuration of the printer. Examples of such management events are configuration change of subunits." SYNTAX INTEGER { other(1), unknown(2), untrained(3), trained(4), fieldService(5), management(6), noInterventionRequired(7) -- Not in RFC 1759 } PrtAlertGroupTC ::= TEXTUAL-CONVENTION -- Values in the range 1 to 29 must not be IANA-assigned without -- re-publishing Printer MIB. -- Values of 30 and greater are for use in MIBs that augment -- the Printer MIB, such as the Finisher MIB. -- This TC extracted from prtAlertGroup in RFC 1759. STATUS current DESCRIPTION "The type of subunit within the printer model that this alert is related. Input, output, and markers are examples of printer model groups, i.e., examples of types of subunits. Wherever possible, the enumerations match the sub-identifier that identifies the relevant table in the Printer MIB. NOTE: Alert type codes have been added for the Host Resources MIB storage table and device table. These additional types are for situations in which the printer's storage and device objects must generate alerts (and possibly traps for critical alerts)." SYNTAX INTEGER { other(1), unknown(2), -- Values for Host Resources MIB hostResourcesMIBStorageTable(3), hostResourcesMIBDeviceTable(4), -- Values for Printer MIB generalPrinter(5), cover(6), localization(7), input(8), output(9), marker(10), markerSupplies(11), markerColorant(12), mediaPath(13), channel(14), interpreter(15), consoleDisplayBuffer(16), consoleLights(17), alert(18), -- Not in RFC 1759 -- Values (5) to (29) reserved for Printer MIB -- Values for Finisher MIB finDevice(30), -- Not in RFC 1759 finSupply(31), -- Not in RFC 1759 finSupplyMediaInput(32), -- Not in RFC 1759 finAttribute(33), -- Not in RFC 1759 -- Values (30) to (39) reserved for Finisher MIB -- Values for the ScanDevice scanDevice(50), -- MFD Extension scanner(51), -- MFD Extension scanMediaPath(52), -- MFD Extension -- Values (50) to (59) reserved for the ScanDevice -- Values for the FaxDevice faxDevice(60), -- MFD Extension faxModem(61), -- MFD Extension -- Values (60) to (69) reserved for the FaxDevice -- Values for other common subunits outputChannel(70) -- MFD Extension -- Values (70) to (79) reserved for common subunits } PrtAlertCodeTC ::= TEXTUAL-CONVENTION -- This TC was extracted from prtAlertCode in RFC 1759. STATUS current DESCRIPTION "The code that describes the type of alert for this entry in the table. Binary change event alerts describe states of the subunit while unary change event alerts describe a single event. The same alert code can be used for a binary change event or a unary change event, depending on implementation. Also, the same alert code can be used to indicate a critical or non-critical (warning) alert, depending on implementation. The value of prtAlertSeverityLevel specifies binary vs. unary and critical vs. non-critical for each event for the implementation. While there are some specific codes for many subunits, the generic codes should be used for most subunit alerts. The network management station can then query the subunit specified by prtAlertGroup to determine further subunit status and other subunit information. An agent shall not add two entries to the alert table for the same event, one containing a generic event code and the other containing a specific event code; the agent shall add only one entry in the alert table for each event; either generic (preferred) or specific, not both. Implementation of the unary change event alertRemovalOfBinaryChangeEntry(1801) is optional. When implemented, this alert code shall indicate to network management stations that the trailing edge of a binary change event has occurred and the corresponding alert entry has been removed from the alert table. As with all events, the alertRemovalOfBinaryChangeEntry(1801) alert shall be placed at the end of the alert table. Such an alert table entry shall specify the following information: prtAlertSeverityLevel warningUnaryChangeEvent(4) prtAlertTrainingLevel noInterventionRequired(7) prtAlertGroup alert(18) prtAlertGroupIndex the index of the row in the alert table of the binary change event that this event has removed. prtAlertLocation unknown (-2) prtAlertCode alertRemovalOfBinaryChangeEntry(1801) prtAlertDescription prtAlertTime the value of sysUpTime at the time of the removal of the binary change event from the alert table. Optionally, the agent may generate a trap coincident with removing the binary change event and placing the unary change event alertRemovalOfBinaryChangeEntry(1801) in the alert table. For such a trap, the prtAlertIndex sent with the above trap parameters shall be the index of the alertRemovalOfBinaryChangeEvent row that was added to the prtAlertTable; not the index of the row that was removed from the prtAlertTable." SYNTAX INTEGER { other(1), -- an event that is not represented -- by one of the alert codes -- specified below. unknown(2), -- The following generic codes are common to -- multiple groups. The NMS may examine the -- prtAlertGroup object to determine what group -- to query for further information. coverOpen(3), coverClosed(4), interlockOpen(5), interlockClosed(6), configurationChange(7), jam(8), subunitMissing(9), -- Not in RFC 1759 -- The subunit tray, bin, etc. -- has been removed. subunitLifeAlmostOver(10), -- Not in RFC 1759 subunitLifeOver(11), -- Not in RFC 1759 subunitAlmostEmpty(12), -- Not in RFC 1759 subunitEmpty(13), -- Not in RFC 1759 subunitAlmostFull(14), -- Not in RFC 1759 subunitFull(15), -- Not in RFC 1759 subunitNearLimit(16), -- Not in RFC 1759 subunitAtLimit(17), -- Not in RFC 1759 subunitOpened(18), -- Not in RFC 1759 subunitClosed(19), -- Not in RFC 1759 subunitTurnedOn(20), -- Not in RFC 1759 subunitTurnedOff(21), -- Not in RFC 1759 subunitOffline(22), -- Not in RFC 1759 subunitPowerSaver(23), -- Not in RFC 1759 subunitWarmingUp(24), -- Not in RFC 1759 subunitAdded(25), -- Not in RFC 1759 subunitRemoved(26), -- Not in RFC 1759 subunitResourceAdded(27), -- Not in RFC 1759 subunitResourceRemoved(28), -- Not in RFC 1759 subunitRecoverableFailure(29), -- Not in RFC 1759 subunitUnrecoverableFailure(30), -- Not in RFC 1759 subunitRecoverableStorageError(31), -- Not in RFC 1759 subunitUnrecoverableStorageError(32), -- Not in RFC 1759 subunitMotorFailure(33), -- Not in RFC 1759 subunitMemoryExhausted(34), -- Not in RFC 1759 subunitUnderTemperature(35), -- Not in RFC 1759 subunitOverTemperature(36), -- Not in RFC 1759 subunitTimingFailure(37), -- Not in RFC 1759 subunitThermistorFailure(38), -- Not in RFC 1759 -- General Printer group doorOpen(501), -- DEPRECATED -- Use coverOpened(3) doorClosed(502), -- DEPRECATED -- Use coverClosed(4) powerUp(503), powerDown(504), printerNMSReset(505), -- Not in RFC 1759 -- The printer has been reset by some -- network management station(NMS) -- writing into 'prtGeneralReset'. printerManualReset(506), -- Not in RFC 1759 -- The printer has been reset manually. printerReadyToPrint(507), -- Not in RFC 1759 -- The printer is ready to print. (i.e., -- not warming up, not in power save -- state, not adjusting print quality, -- etc.). -- Input Group inputMediaTrayMissing(801), inputMediaSizeChange(802), inputMediaWeightChange(803), inputMediaTypeChange(804), inputMediaColorChange(805), inputMediaFormPartsChange(806), inputMediaSupplyLow(807), inputMediaSupplyEmpty(808), inputMediaChangeRequest(809), -- Not in RFC 1759 -- An interpreter has detected that a -- different medium is need in this input -- tray subunit. The prtAlertDescription may -- be used to convey a human readable -- description of the medium required to -- satisfy the request. inputManualInputRequest(810), -- Not in RFC 1759 -- An interpreter has detected that manual -- input is required in this subunit. The -- prtAlertDescription may be used to convey -- a human readable description of the medium -- required to satisfy the request. inputTrayPositionFailure(811), -- Not in RFC 1759 -- The input tray failed to position correctly. inputTrayElevationFailure(812), -- Not in RFC 1759 inputCannotFeedSizeSelected(813), -- Not in RFC 1759 inputMediaTrayFeedError(814), inputMediaTrayJam(815), inputMediaTrayFailure(816), inputMediaTrayPickRollerLifeWarn(817), inputMediaTrayPickRollerLifeOver(818), inputMediaTrayPickRollerFailure(819), inputMediaTrayPickRollerMissing(820), -- Output Group outputMediaTrayMissing(901), outputMediaTrayAlmostFull(902), outputMediaTrayFull(903), outputMailboxSelectFailure(904), -- Not in RFC 1759 outputMediaTrayFeedError(905), outputMediaTrayJam(906), outputMediaTrayFailure(907), -- Marker group markerFuserUnderTemperature(1001), markerFuserOverTemperature(1002), markerFuserTimingFailure(1003), -- Not in RFC 1759 markerFuserThermistorFailure(1004), -- Not in RFC 1759 markerAdjustingPrintQuality(1005), -- Not in RFC 1759 -- Marker Supplies group markerTonerEmpty(1101), markerInkEmpty(1102), markerPrintRibbonEmpty(1103), markerTonerAlmostEmpty(1104), markerInkAlmostEmpty(1105), markerPrintRibbonAlmostEmpty(1106), markerWasteTonerReceptacleAlmostFull(1107), markerWasteInkReceptacleAlmostFull(1108), markerWasteTonerReceptacleFull(1109), markerWasteInkReceptacleFull(1110), markerOpcLifeAlmostOver(1111), markerOpcLifeOver(1112), markerDeveloperAlmostEmpty(1113), markerDeveloperEmpty(1114), markerTonerCartridgeMissing(1115), -- Not in RFC 1759 markerCleanerMissing(1116), markerDeveloperMissing(1117), markerFuserMissing(1118), markerInkMissing(1119), markerOpcMissing(1120), markerPrintRibbonMissing(1121), markerSupplyAlmostEmpty(1122), markerSupplyEmpty(1123), markerSupplyMissing(1124), markerWasteAlmostFull(1125), markerWasteFull(1126), markerWasteMissing(1127), markerWasteInkReceptacleMissing(1128), markerWasteTonerReceptacleMissing(1129), markerTonerMissing(1130), -- Media Path Device Group mediaPathMediaTrayMissing(1301), mediaPathMediaTrayAlmostFull(1302), mediaPathMediaTrayFull(1303), mediaPathCannotDuplexMediaSelected(1304), -- Not in RFC 1759 mediaPathFailure(1305), mediaPathJam(1306), mediaPathInputRequest(1310), mediaPathInputFeedError(1311), mediaPathInputJam(1312), mediaPathOutputFeedError(1321), mediaPathOutputJam(1322), mediaPathOutputFull(1323), mediaPathPickRollerLifeWarn(1331), mediaPathPickRollerLifeOver(1332), mediaPathPickRollerFailure(1333), mediaPathPickRollerMissing(1334), -- Interpreter Group interpreterMemoryIncrease(1501), interpreterMemoryDecrease(1502), interpreterCartridgeAdded(1503), interpreterCartridgeDeleted(1504), interpreterResourceAdded(1505), interpreterResourceDeleted(1506), interpreterResourceUnavailable(1507), interpreterComplexPageEncountered(1509), -- Not in RFC 1759 -- The interpreter has encountered a page -- that is too complex for the resources that -- are available. -- Scanner Group scannerLightLifeAlmostOver(5101), scannerLightLifeOver(5102), scannerLightFailure(5103), scannerLightMissing(5104), scannerSensorLifeAlmostOver(5111), scannerSensorLifeOver(5112), scannerSensorFailure(5113), scannerSensorMissing(5114), -- Scan Media Path Group scanMediaPathTrayMissing(5201), scanMediaPathTrayAlmostFull(5202), scanMediaPathTrayFull(5203), scanMediaPathFailure(5205), scanMediaPathJam(5206), scanMediaPathInputRequest(5210), scanMediaPathInputFeedError(5211), scanMediaPathInputJam(5212), scanMediaPathOutputFeedError(5221), scanMediaPathOutputJam(5222), scanMediaPathOutputFull(5223), scanMediaPathPickRollerLifeWarn(5231), scanMediaPathPickRollerLifeOver(5232), scanMediaPathPickRollerFailure(5233), scanMediaPathPickRollerMissing(5234), -- Fax Modem Group faxModemMissing(6101), faxModemLifeAlmostOver(6102), faxModemLifeOver(6103), faxModemTurnedOn(6104), faxModemTurnedOff(6105), faxModemInactivityTimeout(6110), -- DEPRECATED faxModemProtocolAlert(6111), -- DEPRECATED faxModemEquipmentFailure(6112), -- DEPRECATED faxModemNoDialTone(6113), -- DEPRECATED faxModemLineBusy(6114), -- DEPRECATED faxModemNoAnswer(6115), -- DEPRECATED faxModemVoiceDetected(6116), -- DEPRECATED faxModemCarrierLost(6117), -- DEPRECATED faxModemTrainingFailure(6118), -- DEPRECATED -- Alert Group alertRemovalOfBinaryChangeEntry(1801), -- Not in RFC 1759 -- A binary change event entry has been -- removed from the alert table. This unary -- change alert table entry is added to the -- end of the alert table. -- FinDeviceTypeTC = stitcher(3) -> stapler -- FinStitchingTypeTC = staple... (4,5,6,7, or 10) staplerCoverOpen(30203), staplerCoverClosed(30204), staplerInterlockOpen(30205), staplerInterlockClosed(30206), staplerConfigurationChange(30207), staplerJam(30208), staplerMissing(30209), staplerLifeAlmostOver(30210), staplerLifeOver(30211), staplerAlmostEmpty(30212), staplerEmpty(30213), staplerAlmostFull(30214), staplerFull(30215), staplerNearLimit(30216), staplerAtLimit(30217), staplerOpened(30218), staplerClosed(30219), staplerTurnedOn(30220), staplerTurnedOff(30221), staplerOffline(30222), staplerPowerSaver(30223), staplerWarmingUp(30224), staplerAdded(30225), staplerRemoved(30226), staplerResourceAdded(30227), staplerResourceRemoved(30228), staplerRecoverableFailure(30229), staplerUnrecoverableFailure(30230), staplerRecoverableStorageError(30231), staplerUnrecoverableStorageError(30232), staplerMotorFailure(30233), staplerMemoryExhausted(30234), staplerUnderTemperature(30235), staplerOverTemperature(30236), staplerTimingFailure(30237), staplerThermistorFailure(30238), -- FinDeviceTypeTC = stitcher(3) -> stitcher -- FinStitchingTypeTC = saddleStitch(8) or edgeStitch(9) stitcherCoverOpen(30303), stitcherCoverClosed(30304), stitcherInterlockOpen(30305), stitcherInterlockClosed(30306), stitcherConfigurationChange(30307), stitcherJam(30308), stitcherMissing(30309), stitcherLifeAlmostOver(30310), stitcherLifeOver(30311), stitcherAlmostEmpty(30312), stitcherEmpty(30313), stitcherAlmostFull(30314), stitcherFull(30315), stitcherNearLimit(30316), stitcherAtLimit(30317), stitcherOpened(30318), stitcherClosed(30319), stitcherTurnedOn(30320), stitcherTurnedOff(30321), stitcherOffline(30322), stitcherPowerSaver(30323), stitcherWarmingUp(30324), stitcherAdded(30325), stitcherRemoved(30326), stitcherResourceAdded(30327), stitcherResourceRemoved(30328), stitcherRecoverableFailure(30329), stitcherUnrecoverableFailure(30330), stitcherRecoverableStorageError(30331), stitcherUnrecoverableStorageError(30332), stitcherMotorFailure(30333), stitcherMemoryExhausted(30334), stitcherUnderTemperature(30335), stitcherOverTemperature(30336), stitcherTimingFailure(30337), stitcherThermistorFailure(30338), -- FinDeviceTypeTC = folder(4) folderCoverOpen(30403), folderCoverClosed(30404), folderInterlockOpen(30405), folderInterlockClosed(30406), folderConfigurationChange(30407), folderJam(30408), folderMissing(30409), folderLifeAlmostOver(30410), folderLifeOver(30411), folderAlmostEmpty(30412), folderEmpty(30413), folderAlmostFull(30414), folderFull(30415), folderNearLimit(30416), folderAtLimit(30417), folderOpened(30418), folderClosed(30419), folderTurnedOn(30420), folderTurnedOff(30421), folderOffline(30422), folderPowerSaver(30423), folderWarmingUp(30424), folderAdded(30425), folderRemoved(30426), folderResourceAdded(30427), folderResourceRemoved(30428), folderRecoverableFailure(30429), folderUnrecoverableFailure(30430), folderRecoverableStorageError(30431), folderUnrecoverableStorageError(30432), folderMotorFailure(30433), folderMemoryExhausted(30434), folderUnderTemperature(30435), folderOverTemperature(30436), folderTimingFailure(30437), folderThermistorFailure(30438), -- FinDeviceTypeTC = binder(5) binderCoverOpen(30503), binderCoverClosed(30504), binderInterlockOpen(30505), binderInterlockClosed(30506), binderConfigurationChange(30507), binderJam(30508), binderMissing(30509), binderLifeAlmostOver(30510), binderLifeOver(30511), binderAlmostEmpty(30512), binderEmpty(30513), binderAlmostFull(30514), binderFull(30515), binderNearLimit(30516), binderAtLimit(30517), binderOpened(30518), binderClosed(30519), binderTurnedOn(30520), binderTurnedOff(30521), binderOffline(30522), binderPowerSaver(30523), binderWarmingUp(30524), binderAdded(30525), binderRemoved(30526), binderResourceAdded(30527), binderResourceRemoved(30528), binderRecoverableFailure(30529), binderUnrecoverableFailure(30530), binderRecoverableStorageError(30531), binderUnrecoverableStorageError(30532), binderMotorFailure(30533), binderMemoryExhausted(30534), binderUnderTemperature(30535), binderOverTemperature(30536), binderTimingFailure(30537), binderThermistorFailure(30538), -- FinDeviceTypeTC = trimmer(6) trimmerCoverOpen(30603), trimmerCoverClosed(30604), trimmerInterlockOpen(30605), trimmerInterlockClosed(30606), trimmerConfigurationChange(30607), trimmerJam(30608), trimmerMissing(30609), trimmerLifeAlmostOver(30610), trimmerLifeOver(30611), trimmerAlmostEmpty(30612), trimmerEmpty(30613), trimmerAlmostFull(30614), trimmerFull(30615), trimmerNearLimit(30616), trimmerAtLimit(30617), trimmerOpened(30618), trimmerClosed(30619), trimmerTurnedOn(30620), trimmerTurnedOff(30621), trimmerOffline(30622), trimmerPowerSaver(30623), trimmerWarmingUp(30624), trimmerAdded(30625), trimmerRemoved(30626), trimmerResourceAdded(30627), trimmerResourceRemoved(30628), trimmerRecoverableFailure(30629), trimmerUnrecoverableFailure(30630), trimmerRecoverableStorageError(30631), trimmerUnrecoverableStorageError(30632), trimmerMotorFailure(30633), trimmerMemoryExhausted(30634), trimmerUnderTemperature(30635), trimmerOverTemperature(30636), trimmerTimingFailure(30637), trimmerThermistorFailure(30638), -- FinDeviceTypeTC = dieCutter(7) dieCutterCoverOpen(30703), dieCutterCoverClosed(30704), dieCutterInterlockOpen(30705), dieCutterInterlockClosed(30706), dieCutterConfigurationChange(30707), dieCutterJam(30708), dieCutterMissing(30709), dieCutterLifeAlmostOver(30710), dieCutterLifeOver(30711), dieCutterAlmostEmpty(30712), dieCutterEmpty(30713), dieCutterAlmostFull(30714), dieCutterFull(30715), dieCutterNearLimit(30716), dieCutterAtLimit(30717), dieCutterOpened(30718), dieCutterClosed(30719), dieCutterTurnedOn(30720), dieCutterTurnedOff(30721), dieCutterOffline(30722), dieCutterPowerSaver(30723), dieCutterWarmingUp(30724), dieCutterAdded(30725), dieCutterRemoved(30726), dieCutterResourceAdded(30727), dieCutterResourceRemoved(30728), dieCutterRecoverableFailure(30729), dieCutterUnrecoverableFailure(30730), dieCutterRecoverableStorageError(30731), dieCutterUnrecoverableStorageError(30732), dieCutterMotorFailure(30733), dieCutterMemoryExhausted(30734), dieCutterUnderTemperature(30735), dieCutterOverTemperature(30736), dieCutterTimingFailure(30737), dieCutterThermistorFailure(30738), -- FinDeviceTypeTC = puncher(8) puncherCoverOpen(30803), puncherCoverClosed(30804), puncherInterlockOpen(30805), puncherInterlockClosed(30806), puncherConfigurationChange(30807), puncherJam(30808), puncherMissing(30809), puncherLifeAlmostOver(30810), puncherLifeOver(30811), puncherAlmostEmpty(30812), puncherEmpty(30813), puncherAlmostFull(30814), puncherFull(30815), puncherNearLimit(30816), puncherAtLimit(30817), puncherOpened(30818), puncherClosed(30819), puncherTurnedOn(30820), puncherTurnedOff(30821), puncherOffline(30822), puncherPowerSaver(30823), puncherWarmingUp(30824), puncherAdded(30825), puncherRemoved(30826), puncherResourceAdded(30827), puncherResourceRemoved(30828), puncherRecoverableFailure(30829), puncherUnrecoverableFailure(30830), puncherRecoverableStorageError(30831), puncherUnrecoverableStorageError(30832), puncherMotorFailure(30833), puncherMemoryExhausted(30834), puncherUnderTemperature(30835), puncherOverTemperature(30836), puncherTimingFailure(30837), puncherThermistorFailure(30838), -- FinDeviceTypeTC = perforater(9) perforaterCoverOpen(30903), perforaterCoverClosed(30904), perforaterInterlockOpen(30905), perforaterInterlockClosed(30906), perforaterConfigurationChange(30907), perforaterJam(30908), perforaterMissing(30909), perforaterLifeAlmostOver(30910), perforaterLifeOver(30911), perforaterAlmostEmpty(30912), perforaterEmpty(30913), perforaterAlmostFull(30914), perforaterFull(30915), perforaterNearLimit(30916), perforaterAtLimit(30917), perforaterOpened(30918), perforaterClosed(30919), perforaterTurnedOn(30920), perforaterTurnedOff(30921), perforaterOffline(30922), perforaterPowerSaver(30923), perforaterWarmingUp(30924), perforaterAdded(30925), perforaterRemoved(30926), perforaterResourceAdded(30927), perforaterResourceRemoved(30928), perforaterRecoverableFailure(30929), perforaterUnrecoverableFailure(30930), perforaterRecoverableStorageError(30931), perforaterUnrecoverableStorageError(30932), perforaterMotorFailure(30933), perforaterMemoryExhausted(30934), perforaterUnderTemperature(30935), perforaterOverTemperature(30936), perforaterTimingFailure(30937), perforaterThermistorFailure(30938), -- FinDeviceTypeTC = slitter(10) slitterCoverOpen(31003), slitterCoverClosed(31004), slitterInterlockOpen(31005), slitterInterlockClosed(31006), slitterConfigurationChange(31007), slitterJam(31008), slitterMissing(31009), slitterLifeAlmostOver(31010), slitterLifeOver(31011), slitterAlmostEmpty(31012), slitterEmpty(31013), slitterAlmostFull(31014), slitterFull(31015), slitterNearLimit(31016), slitterAtLimit(31017), slitterOpened(31018), slitterClosed(31019), slitterTurnedOn(31020), slitterTurnedOff(31021), slitterOffline(31022), slitterPowerSaver(31023), slitterWarmingUp(31024), slitterAdded(31025), slitterRemoved(31026), slitterResourceAdded(31027), slitterResourceRemoved(31028), slitterRecoverableFailure(31029), slitterUnrecoverableFailure(31030), slitterRecoverableStorageError(31031), slitterUnrecoverableStorageError(31032), slitterMotorFailure(31033), slitterMemoryExhausted(31034), slitterUnderTemperature(31035), slitterOverTemperature(31036), slitterTimingFailure(31037), slitterThermistorFailure(31038), -- FinDeviceTypeTC = separationCutter(11) separationCutterCoverOpen(31103), separationCutterCoverClosed(31104), separationCutterInterlockOpen(31105), separationCutterInterlockClosed(31106), separationCutterConfigurationChange(31107), separationCutterJam(31108), separationCutterMissing(31109), separationCutterLifeAlmostOver(31110), separationCutterLifeOver(31111), separationCutterAlmostEmpty(31112), separationCutterEmpty(31113), separationCutterAlmostFull(31114), separationCutterFull(31115), separationCutterNearLimit(31116), separationCutterAtLimit(31117), separationCutterOpened(31118), separationCutterClosed(31119), separationCutterTurnedOn(31120), separationCutterTurnedOff(31121), separationCutterOffline(31122), separationCutterPowerSaver(31123), separationCutterWarmingUp(31124), separationCutterAdded(31125), separationCutterRemoved(31126), separationCutterResourceAdded(31127), separationCutterResourceRemoved(31128), separationCutterRecoverableFailure(31129), separationCutterUnrecoverableFailure(31130), separationCutterRecoverableStorageError(31131), separationCutterUnrecoverableStorageError(31132), separationCutterMotorFailure(31133), separationCutterMemoryExhausted(31134), separationCutterUnderTemperature(31135), separationCutterOverTemperature(31136), separationCutterTimingFailure(31137), separationCutterThermistorFailure(31138), -- FinDeviceTypeTC = imprinter(12) imprinterCoverOpen(31203), imprinterCoverClosed(31204), imprinterInterlockOpen(31205), imprinterInterlockClosed(31206), imprinterConfigurationChange(31207), imprinterJam(31208), imprinterMissing(31209), imprinterLifeAlmostOver(31210), imprinterLifeOver(31211), imprinterAlmostEmpty(31212), imprinterEmpty(31213), imprinterAlmostFull(31214), imprinterFull(31215), imprinterNearLimit(31216), imprinterAtLimit(31217), imprinterOpened(31218), imprinterClosed(31219), imprinterTurnedOn(31220), imprinterTurnedOff(31221), imprinterOffline(31222), imprinterPowerSaver(31223), imprinterWarmingUp(31224), imprinterAdded(31225), imprinterRemoved(31226), imprinterResourceAdded(31227), imprinterResourceRemoved(31228), imprinterRecoverableFailure(31229), imprinterUnrecoverableFailure(31230), imprinterRecoverableStorageError(31231), imprinterUnrecoverableStorageError(31232), imprinterMotorFailure(31233), imprinterMemoryExhausted(31234), imprinterUnderTemperature(31235), imprinterOverTemperature(31236), imprinterTimingFailure(31237), imprinterThermistorFailure(31238), -- FinDeviceTypeTC = wrapper(13) wrapperCoverOpen(31303), wrapperCoverClosed(31304), wrapperInterlockOpen(31305), wrapperInterlockClosed(31306), wrapperConfigurationChange(31307), wrapperJam(31308), wrapperMissing(31309), wrapperLifeAlmostOver(31310), wrapperLifeOver(31311), wrapperAlmostEmpty(31312), wrapperEmpty(31313), wrapperAlmostFull(31314), wrapperFull(31315), wrapperNearLimit(31316), wrapperAtLimit(31317), wrapperOpened(31318), wrapperClosed(31319), wrapperTurnedOn(31320), wrapperTurnedOff(31321), wrapperOffline(31322), wrapperPowerSaver(31323), wrapperWarmingUp(31324), wrapperAdded(31325), wrapperRemoved(31326), wrapperResourceAdded(31327), wrapperResourceRemoved(31328), wrapperRecoverableFailure(31329), wrapperUnrecoverableFailure(31330), wrapperRecoverableStorageError(31331), wrapperUnrecoverableStorageError(31332), wrapperMotorFailure(31333), wrapperMemoryExhausted(31334), wrapperUnderTemperature(31335), wrapperOverTemperature(31336), wrapperTimingFailure(31337), wrapperThermistorFailure(31338), -- FinDeviceTypeTC = bander(14) banderCoverOpen(31403), banderCoverClosed(31404), banderInterlockOpen(31405), banderInterlockClosed(31406), banderConfigurationChange(31407), banderJam(31408), banderMissing(31409), banderLifeAlmostOver(31410), banderLifeOver(31411), banderAlmostEmpty(31412), banderEmpty(31413), banderAlmostFull(31414), banderFull(31415), banderNearLimit(31416), banderAtLimit(31417), banderOpened(31418), banderClosed(31419), banderTurnedOn(31420), banderTurnedOff(31421), banderOffline(31422), banderPowerSaver(31423), banderWarmingUp(31424), banderAdded(31425), banderRemoved(31426), banderResourceAdded(31427), banderResourceRemoved(31428), banderRecoverableFailure(31429), banderUnrecoverableFailure(31430), banderRecoverableStorageError(31431), banderUnrecoverableStorageError(31432), banderMotorFailure(31433), banderMemoryExhausted(31434), banderUnderTemperature(31435), banderOverTemperature(31436), banderTimingFailure(31437), banderThermistorFailure(31438), -- FinDeviceTypeTC = makeEnvelope(15) makeEnvelopeCoverOpen(31503), makeEnvelopeCoverClosed(31504), makeEnvelopeInterlockOpen(31505), makeEnvelopeInterlockClosed(31506), makeEnvelopeConfigurationChange(31507), makeEnvelopeJam(31508), makeEnvelopeMissing(31509), makeEnvelopeLifeAlmostOver(31510), makeEnvelopeLifeOver(31511), makeEnvelopeAlmostEmpty(31512), makeEnvelopeEmpty(31513), makeEnvelopeAlmostFull(31514), makeEnvelopeFull(31515), makeEnvelopeNearLimit(31516), makeEnvelopeAtLimit(31517), makeEnvelopeOpened(31518), makeEnvelopeClosed(31519), makeEnvelopeTurnedOn(31520), makeEnvelopeTurnedOff(31521), makeEnvelopeOffline(31522), makeEnvelopePowerSaver(31523), makeEnvelopeWarmingUp(31524), makeEnvelopeAdded(31525), makeEnvelopeRemoved(31526), makeEnvelopeResourceAdded(31527), makeEnvelopeResourceRemoved(31528), makeEnvelopeRecoverableFailure(31529), makeEnvelopeUnrecoverableFailure(31530), makeEnvelopeRecoverableStorageError(31531), makeEnvelopeUnrecoverableStorageError(31532), makeEnvelopeMotorFailure(31533), makeEnvelopeMemoryExhausted(31534), makeEnvelopeUnderTemperature(31535), makeEnvelopeOverTemperature(31536), makeEnvelopeTimingFailure(31537), makeEnvelopeThermistorFailure(31538), -- FinDeviceTypeTC = stacker(16) stackerCoverOpen(31603), stackerCoverClosed(31604), stackerInterlockOpen(31605), stackerInterlockClosed(31606), stackerConfigurationChange(31607), stackerJam(31608), stackerMissing(31609), stackerLifeAlmostOver(31610), stackerLifeOver(31611), stackerAlmostEmpty(31612), stackerEmpty(31613), stackerAlmostFull(31614), stackerFull(31615), stackerNearLimit(31616), stackerAtLimit(31617), stackerOpened(31618), stackerClosed(31619), stackerTurnedOn(31620), stackerTurnedOff(31621), stackerOffline(31622), stackerPowerSaver(31623), stackerWarmingUp(31624), stackerAdded(31625), stackerRemoved(31626), stackerResourceAdded(31627), stackerResourceRemoved(31628), stackerRecoverableFailure(31629), stackerUnrecoverableFailure(31630), stackerRecoverableStorageError(31631), stackerUnrecoverableStorageError(31632), stackerMotorFailure(31633), stackerMemoryExhausted(31634), stackerUnderTemperature(31635), stackerOverTemperature(31636), stackerTimingFailure(31637), stackerThermistorFailure(31638), -- FinDeviceTypeTC = sheetRotator(17) sheetRotatorCoverOpen(31703), sheetRotatorCoverClosed(31704), sheetRotatorInterlockOpen(31705), sheetRotatorInterlockClosed(31706), sheetRotatorConfigurationChange(31707), sheetRotatorJam(31708), sheetRotatorMissing(31709), sheetRotatorLifeAlmostOver(31710), sheetRotatorLifeOver(31711), sheetRotatorAlmostEmpty(31712), sheetRotatorEmpty(31713), sheetRotatorAlmostFull(31714), sheetRotatorFull(31715), sheetRotatorNearLimit(31716), sheetRotatorAtLimit(31717), sheetRotatorOpened(31718), sheetRotatorClosed(31719), sheetRotatorTurnedOn(31720), sheetRotatorTurnedOff(31721), sheetRotatorOffline(31722), sheetRotatorPowerSaver(31723), sheetRotatorWarmingUp(31724), sheetRotatorAdded(31725), sheetRotatorRemoved(31726), sheetRotatorResourceAdded(31727), sheetRotatorResourceRemoved(31728), sheetRotatorRecoverableFailure(31729), sheetRotatorUnrecoverableFailure(31730), sheetRotatorRecoverableStorageError(31731), sheetRotatorUnrecoverableStorageError(31732), sheetRotatorMotorFailure(31733), sheetRotatorMemoryExhausted(31734), sheetRotatorUnderTemperature(31735), sheetRotatorOverTemperature(31736), sheetRotatorTimingFailure(31737), sheetRotatorThermistorFailure(31738), -- FinDeviceTypeTC = inserter(18) inserterCoverOpen(31803), inserterCoverClosed(31804), inserterInterlockOpen(31805), inserterInterlockClosed(31806), inserterConfigurationChange(31807), inserterJam(31808), inserterMissing(31809), inserterLifeAlmostOver(31810), inserterLifeOver(31811), inserterAlmostEmpty(31812), inserterEmpty(31813), inserterAlmostFull(31814), inserterFull(31815), inserterNearLimit(31816), inserterAtLimit(31817), inserterOpened(31818), inserterClosed(31819), inserterTurnedOn(31820), inserterTurnedOff(31821), inserterOffline(31822), inserterPowerSaver(31823), inserterWarmingUp(31824), inserterAdded(31825), inserterRemoved(31826), inserterResourceAdded(31827), inserterResourceRemoved(31828), inserterRecoverableFailure(31829), inserterUnrecoverableFailure(31830), inserterRecoverableStorageError(31831), inserterUnrecoverableStorageError(31832), inserterMotorFailure(31833), inserterMemoryExhausted(31834), inserterUnderTemperature(31835), inserterOverTemperature(31836), inserterTimingFailure(31837), inserterThermistorFailure(31838) } END