4.38 Debugging and Tracing Programs

This section is a reference to the debugger interaction predicates. A more use-oriented overview of the debugger is in section 2.9.

If you have installed XPCE, you can use the graphical front-end of the tracer. This front-end is installed using the predicate guitracer/0.

trace

Start the tracer. trace/0 itself cannot be seen in the tracer. Note that the Prolog top-level treats trace/0 special; it means `trace the next goal'.

tracing

True if the tracer is currently switched on. tracing/0 itself can not be seen in the tracer.

notrace

Stop the tracer. notrace/0 itself cannot be seen in the tracer.

guitracer

Installs hooks (see prolog_trace_interception/4) into the system that redirects tracing information to a GUI front-end providing structured access to variable-bindings, graphical overview of the stack and highlighting of relevant source-code.

noguitracer

Reverts back to the textual tracer.

trace(+Pred)

Equivalent to trace(Pred, +all).

trace(+Pred, +Ports)

Put a trace-point on all predicates satisfying the predicate specification Pred. Ports is a list of port names (call, redo, exit, fail). The atom all refers to all ports. If the port is preceded by a - sign the trace-point is cleared for the port. If it is preceded by a + the trace-point is set.

The predicate trace/2 activates debug mode (see debug/0). Each time a port (of the 4-port model) is passed that has a trace-point set the goal is printed as with trace/0. Unlike trace/0 however, the execution is continued without asking for further information. Examples:

?- trace(hello).	Trace all ports of hello with any arity in any module.
?- trace(foo/2, +fail).	Trace failures of foo/2 in any module.
?- trace(bar/1, -all).	Stop tracing bar/1.

The predicate debugging/0 shows all currently defined trace-points.

notrace(+Goal)

Call Goal, but suspend the debugger while Goal is executing. The current implementation cuts the choice-points of Goal after successful completion. See once/1. Later implementations may have the same semantics as call/1.

debug

Start debugger. In debug mode, Prolog stops at spy- and trace-points, disables tail-recursion optimisation and aggressive destruction of choice-points to make debugging information accessible. Implemented by the Prolog flag debug.

nodebug

Stop debugger. Implemented by the prolog flag debug. See also debug/0.

debugging

Print debug status and spy points on current output stream. See also the prolog flag debug.

spy(+Pred)

Put a spy point on all predicates meeting the predicate specification Pred. See section 4.4.

nospy(+Pred)

Remove spy point from all predicates meeting the predicate specification Pred.

nospyall

Remove all spy points from the entire program.

leash(?Ports)

Set/query leashing (ports which allow for user interaction). Ports is one of +Name, -Name, ?Name or a list of these. +Name enables leashing on that port, -Name disables it and ?Name succeeds or fails according to the current setting. Recognised ports are: call, redo, exit, fail and unify. The special shorthand all refers to all ports, full refers to all ports except for the unify port (default). half refers to the call, redo and fail port.

visible(+Ports)

Set the ports shown by the debugger. See leash/1 for a description of the port specification. Default is full.

unknown(-Old, +New)

Edinburgh-prolog compatibility predicate, interfacing to the ISO prolog flag unknown. Values are trace (meaning error) and fail. If the unknown flag is set to warning, unknown/2 reports the value as trace.

style_check(+Spec)

Set style checking options. Spec is either +<option>, -<option>, ?(<option>)^{61In older versions `?' was a prefix operator. Inversions after 5.5.13, explicit brackets are needed.} or a list of such options. +<option> sets a style checking option, -<option> clears it and ?(<option>) succeeds or fails according to the current setting. consult/1 and derivatives resets the style checking options to their value before loading the file. If---for example---a file containing long atoms should be loaded the user can start the file with:

:- style_check(-atom).

Currently available options are:

Name	Default	Description
singleton	on	read_clause/1 (used by consult/1) warns on variables only appearing once in a term (clause) which have a name not starting with an underscore.
atom	on	read/1 and derivatives will produce an error message on quoted atoms or strings longer than 5 lines.
dollar	off	Accept dollar as a lower case character, thus avoiding the need for quoting atoms with dollar signs. System maintenance use only.
discontiguous	on	Warn if the clauses for a predicate are not together in the same source file.
string	off	Backward compatibility. See the prolog-flag double_quotes (current_prolog_flag/2).
charset	off	Warn on atoms and variables holding non-ASCII characters that are not quoted. See also section 2.15.1.1.